Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
Advanced 8/4-axis Servo & Stepper Motion Controllers with Modular Design
PCIe-8158
-
The PCIe-8158 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8158 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
Product
PCI-6154, 4 AI (16-Bit, 250 kS/s/ch), 4 AO, 6 DI, 4 DO, PCI Multifunction I/O Device
779340-01
-
4 AI (16-Bit, 250 kS/s/ch), 4 AO, 6 DI, 4 DO, PCI Multifunction I/O Device - The PCI‑6154 is a simultaneous-sampling, channel-to-channel isolated DAQ device. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. You can combine the channel‑to‑channel isolated analog outputs to generate signals greater than ±10 V (up to ±40 V by combining all four channels). The PCI‑6154 is ideal for a variety of applications including automotive test, industrial monitoring and control, and high-speed continuous data logging. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Multimeters
METRAHIT Series
-
All multimeters measurevoltage, resistance, frequency, continuity and diode test.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
-
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Condition Monitoring Solutions
VibroLine
-
The VibroLine devices are stationary analysis modules for continuous condition monitoring on machines and systems. The VibroLine condition monitoring system can be used to monitor vibration acceleration, speed or displacement with freely adjustable frequency filtering for different applications. Permanent vibration monitoring of your machines not only brings competitive advantages through the increased efficiency of your systems, but also protects against unwanted machine failures. With the VibroLine devices, you can monitor not only the sum, order and storage characteristics, but also impact characteristics. This offers you enormous flexibility in terms of monitoring parameters for your condition monitoring.
-
Product
Liquid Level Gauges
-
Provides a continuous indication of the liquid level inside of a transformer's main tank, conservator tank or load tap changer compartment with integrated switches that allows limit and alarm functions.
-
Product
Mini Jumbo LCD Autoranging Multimeter
HH2202
-
High Accuracy (Basic Accuracy 1.0%). Jumbo LCD display 4000 count, 21mm figure height. Convenient Auto Ranging. Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 40MΩ. Diode test, audible continuity check
-
Product
Cable Continuity Tester, VGA/UL2919 Mini, Network, 21.01 mm, 35 mm, 45.01 mm
72-9205
-
Quickly test VGA / UL2919 cables No need to carry bulky, expensive cable testers to test only one or two cable types Mini cable tester fits easily in your pocket or tool box, and requires no external power Confirms conductor continuity with sequential LED's Save time and money by diagnosing connectivity issues All units are powered by a cross compatible 3xAA battery pack or USB cable (both included) Most units measure 2" x 2" x 1" or less!
-
Product
On-Board Systems
OBS-ONE series
-
HORIBA developed the OBS-ONE series on-board emission measurement system in response to new requirements for exhaust emissions measurement from vehicles being driven on public roads (Portable Emissions Measurement Systems - PEMS). This development has been made possible by reducing the dimensions and power consumption of laboratory grade analyzers and ensuring that the system components have excellent vibration resistance. The OBS-ONE series continuously measures not only the concentration of CO, CO2, THC and NOx, but also measures exhaust fl ow rate and A/F ratio to calculate mass emission and fuel economy.
-
Product
Controllers
-
Designed for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity in a general purpose industrial environment.
-
Product
Precision Continuous Flow Metering + Dispense System
Graco Dispense Analyzer
-
A whole new level of precision for drivetrain gasketing. Detect air bubbles and defects you couldn't see before. Track critical measurements, including entrapped air. Quickly and easily find a defect's root cause. Avoid expensive problems by responding sooner. Save millions: Contain warranty claims and recalls. The Graco PCF and Analyzer combination: Your ultimate system for accurate, reliable dispensing. The new Graco Dispense Analyzer is a monitoring system capable of detecting the tiniest air bubble or error during adhesive dispensing. Paired with the Graco Precision Continuous Flow (PCF) system, the Analyzer monitors your dispense in real time, detecting immediately if conditions are off and may potentially compromise your final product. With the ability to respond immediately, you can avoid defects that lead to costly recalls. The Analyzer stores the signature of each dispense, giving you the ability to replay the data, even months or years after the actual dispense. Seeing the data replayed as if in real time, you can more easily pinpoint the root cause of the defect and contain a recall or warranty claim to only those products that were affected.
-
Product
RFID Sensor Datenlogger (HF)
TELID®300
-
TELID® sensor data loggers are ideal for complex monitoring of quality assurance and maintenance, or while transporting foods, plants, pharmaceuticals or medical products. Temperature, humidity, pressure or shock-sensitive products can be monitored and traced, for example, during worldwide transportation. microsensys offers calibration services for the TELID®311, 311.ac and 314.ac. We carry out a factory (one- to three-point) calibration according to your temperature specifications, which are based on controlled operations and continuous monitoring, or ISO (one- to more point) calibration for temperature according to DAkkS specifications.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-03
-
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
PXI Dual 3-Channel 10A Solid State MUX
40-666-011
-
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
Product
Hand-held 3-Phase Meter Tester
3 Series
-
Powermetrix continues its industry leadership with the introduction of Powermetrix Remote Manager (PRM) for the PowerMaster® 3 Series. Powermetrix Remote Manager enables wireless control of essential and various metering site accuracy tests contained within PowerMaster® 3 Series from any Windows compliant system up to 100 feet in any environment, including high EMF environments! Customer load Meter Testing, CT/PT ratio testing, CT/PT burden measurement, meter register/demand testing, and wiring verification are all easily performed with this extremely portable, hand-held 3-phase power analyzer. In addition, with the new Model 335, phantom load meter testing and CT burden added testing are available to complete your field-testing needs.
-
Product
High Pressure Gas Conditioners
HPG
-
Bemco HPG, High Pressure Gas Conditioners are similar to the PTS Portable Temperature Conditioners except they are designed for continuous operation at up to two atmospheres (29.4 psia) of pressure. This higher base operating pressure doubles the gas density per cfm of circulating air or gaseous nitrogen allowing the use of smaller connecting tubes while also increasing thermal capability. .
-
Product
Dust Collector Timer Controller
DCT1000
-
Simplify your on-demand cleaning requirements with the Series DCT1000 Dust Collector Timer Controller. Relying on one timer board for on-demand and continuous cleaning applications, the DCT1000 eliminates external devices such as pressure switches, relays and timers.
-
Product
Bat Deterrent Systems
-
As White-Nose Syndrome continues to ravage the populations of many hibernating bat species, the wind industry remains committed to lessening its impact on wildlife, including contributing to bat fatalities. While it is well researched that wind turbines cause mortality to bats, successful minimization methods have been implemented. Presently, the most effective techniques involve curtailment, which requires a reduction in energy generation. NRG Systems understands that this is not an ideal option for wind plant operators, so we have set out to develop Bat Deterrent Systems that could significantly reduce bat take without curtailment, meaning operators can produce more renewable energy more of the time while keeping all bats out of harm’s way.
-
Product
Soil Moisture Sensor
Modbus RS485
-
This is a contact-less capacitive soil moisture sensor, a continuation of my I2C soil moisture sensor. This particular version of the sensor is suited for more professional installations where long cable runs is a requirement. It adds a local voltage regulator to mitigate the voltage drop and RS485 transceiver to accommodate long wires, also reverse polarity and an additional ESD protection level is added.
-
Product
IP-BiSerial-IO
-
The serial Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The programmable output rates and a user oscillator position allow for flexible frequency selection. The adaptable interface allows for bursted or continuous operation, and all kinds of data / handshake protocols.
-
Product
Power Quality Meter
PQMII
-
The PQM II is an ideal choice when continuous monitoring of a three phase system is required. It provides metering for current, voltage, real and reactive power, energy use, cost of power, power factor and frequency. Programmable setpoints and 4 assignable output relays allow control functions to be added for specific applications.
-
Product
Load Cabinet
DFX-20
-
• Working power: AC220V 50Hz • Normal load: Continuous adjustable from 0 to 280V • Electric current: 0～20A/Continuos adjustable cosφ: 0.3-0.96 under 16A; 0.6~0.96 more than 16A • Precision: 0.5 class, digital display • Counter: 0～999999 times, can be preset
-
Product
Power Clamp Meters
-
TES Electrical Electronic Corp.
Communication with PC. 4000 continuity point data logger, 25 point manual data logger. True power/ apparent Power/ Power Fractor Measurement. True RMS. V,A,W cap Ind, phase indicator.
-
Product
Speed Sensors Dust Ignition-Proof
ST420-LT / ST420-DI
-
The patented ST420-LT and ST420-DI detect passing magnets of a shaft-mounted pulser disc or wrap and output a smooth, continuous 4-20 mA analog signal in direct proportion to shaft rotation speed.
-
Product
Sky Quality Meter
SQM-LU
-
A USB SQM model for night-time sky brightness monitoring! An affordable meter for continual, connected measuring of sky brightness for astronomers! The "Sky Quality Meter - LU" measures the brightness of the night sky in magnitudes per square arcsecond.
-
Product
Continuous Gas Analyzer
CT5100
-
Emerson CT5000 series, providing the most comprehensive analysis available as it can detect down to sub ppm level for a range of components, while simplifying operation and significantly reducing costs. Unlike traditional continuous gas analyzers, the CT5100 can measure up to 12 critical component gases and potential pollutants simultaneously within a single system – meeting local, state, national, and international regulatory requirements.
-
Product
PXIe Vector Signal Analyzer: 6 GHz
M9391A
-
RF requirements keep growing while timelines keep shrinking. To help ease the technical and business pressures, the right test solution provides continuity in measurements and longevity in capability. In the evolution of modular RF test solutions, the Keysight PXI VSA is the next logical step in signal analysis. With raw hardware speed and X-Series measurement applications, it delivers proven results faster. From fully modular hardware to software leverage to worldwide support, the PXI VSA is the low-risk way to manage change and be ready for tomorrow today
-
Product
LED Lighting Panel Tester
igentic® 821t
-
Growing demand for light emitting diode (LED) products combined with increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. Sterner Automation, a leader in LED test technology, provides solutions that address these specialized requirements, including the versatile igentic® 821t panel testing system. The igentic® 821t automated process combines advanced vision technology with flexible positioning and power-up capabilities to detect inconsistencies in individual LEDs at the panel production level. The resulting detection capabilities ensure that the highest standards are met while maintaining the capacity associated with today's high speed automated lines.
-
Product
Stack Gas Analyzer
GI-700 series
-
Experience HORIBA, the Global Single Source Solutions Provider with over 50 years of technological advancements and unparalleled reliability, dependability and operability.The GI-700 stack gas analyzer is designed to continuously measure the concentrations of nitrogen oxides (NOx), sulfur dioxide (SO2), carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), and ammonia (NH3) in stack flue gas streams.
-
Product
FT-NIR for Process Analytics
QuasIR™ 2000E
-
Galaxy Scientific’s QuasIR™ 2000E is designed for continuous measurement of the chemical composition of material transported on a conveyor belt, through a pipe, or in a chute. Our unique external projection optics use high powered tungsten lamps to illuminate the sample from as far as 24 inches away and collect the scattered reflection off the sample through a fiber optic cable. The analysis spot size can be set as small as 0.5″ or as large as 8″ in diameter and can be custom tailored to applications needs.
