CT Test Set
-
Product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
-
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
Product
Air Data Test Sets
-
For calibrating altimeters, airspeed indicators, rate-of-climbindicators and other avionic instruments.
-
Product
Radar Altimeter Test Set
Core Technology
-
Eastern OptX core technology enables the conversion of microwave signals to optical signals (E/O), time delaying this signal then reconverting the light back to original microwave signal (O/E) with superior fidelity over traditional time delay methods. Products include Radar Target Simulation, Radar Altimeter Testing, Channel Simulation (Air Interface) and Multipath Creation.
-
-
Product
Optical Loss Test Set
OLTS
-
Tests for the total amount of light loss on a fiber optic link.
-
Product
Primary Injection Test Set
PI-6000
-
The PI-6000 is a rugged & durable primary injection test set capable of testing circuit breakers up to 6,000 amperes frame size. It incorporates an output transformer with dual primaries to facilitate its use on power sources of 480 VAC as well as 208-240 VAC. The unit also includes dual secondaries to provide optimal impedance matching to a wide range of circuit breaker sizes. An internal voltage sensor automatically configures the AC control power section to be energized only when properly configured for the applied voltage.
-
Product
In-Circuit Testing and Test Engineering
Teradyne Z1890
-
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
Product
RF & ECM Test Set
MS 1109
-
The RF Tester is a computer-controlled system used to test the RF Unit, Logic Unit (ECM) and its modules.
-
Product
Digital Transformer BDV Oil Test Set
-
We are engaged in manufacturing, supplying and trading an exhaustive range of High Voltage Oil Test Set, which is developed under the constant supervision of our team of experts. This equipment is acknowledged for its optimality in performance and quality.
-
Product
Digital Clamp Tester With 80mm X 74mm CT With BluetoothRMS, 40mmφCT, ACA
MCL-800DXR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Next-generation leakage current clamp meter with connection, via Bluetooth, to a smartphone which displays waveforms and data.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
Test Port Cable
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
Product
Universal Three-phase Protective Relay Test Set
Mentor-12
-
The Mentor 12 is the most advanced three-phase relay test set available for type and field testing of electromechanical and digital protections of any kind, in traditional or IEC-61850 based substations.
-
Product
Advanced Three Phase Automatic Relay Test Sets
MP 3000 Series
-
Advanced three phase automatic relay test set. PC control through user friendly MPWIN Relay Test Software. High accuracy and high power over wide range. Suitable for IEC61850 GOOSE simulation, subscription and sampled value publishing. CE, FCC.
-
Product
Relay Test Set
-
Relay testing equipment is a portable apparatus designed for checking the operating characteristics of protective relays on site. Rr Relay Testing Equipments are designed to facilitate routine test or periodic maintenance test of relays by simulating (as early as possible) fault conditions under which the protective relays are required to function. There are several approaches to the method of testing relays on site. The Relay Testing Equipments are secondary injection type and are intended to be used to test the relays after isolating them from live systems, either physically or electrically.
-
Product
Test Set
TS® 25D
-
This feature-rich test set is a necessity for a variety of installs. The TS25D Test Set features data lockout and lockout override, making you completely safe in talk or monitor mode. The DSL/POTS filtering technology allows you to safely draw dial tone without downing DSL.
-
Product
Module Retainer Block Set, For Discrete Wiring, 2 Positions
510109117
Mounting Kit
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules hinge down with the receiver to provide easy access to wiring.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Power Probe III Set
PP319FTC
-
Full functioning voltmeter measures in 1/10th of a volt increments from 1/10th of 1V up to 70V. Easy to read dual polarity indicators: red (+) symbol indicates positive green (-) symbol indicates negative. Circuit breaker protects the vehicles electrical system and your Power Probe. 20' extension lead gives you 40' total of lead. Great for RV'S, trucks and trailers.
-
Product
Flexible Cable Set, 2.4 Mm To 7 Mm
85135F
-
Achieve phase stability with these 62.9-cm cables when a DUT is connected between cable ends
-
Product
Test Automation System for Emission Testing
STARS VETS
-
STARS VETS is a Vehicle Emission Test System application available with the STARS Automation platform for chassis, engine and powertrain dynamometers. The application provides test cycle execution, emissions equipment control, results calculation and reporting in compliance with the different legislative standards throughout the global regions. Its flexible design offers a wide range a customization, and it addresses the various requirements for R&D, COP and certification testing.
-
Product
Replacement Solder tip lead set for D420/D620
Dx20-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
OPTICAL LOSS TEST SET (OLTS) MQJ KIT
4000-1025
-
The OLTS (Optical Loss Test Set) - MQJ Kit includes a soft, padded carrying case with strap that is provided to protect all of the components during transportation and/or storage.
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
Spring Clip Fixture
16092A
Test Fixture
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
Performance Testing
-
LOAD TESTINGEvaluates software behavior under a specific expected loadVOLUME TESTINGEvaluates software productivity under an increasing volume of stored and processed dataSTABILITY TESTINGDetermines the effect of configuration changes on the system's performance and behaviorSTRESS TESTINGIdentifies the upper limits of software capacitySCALABILITY TESTINGMeasures software capability under increased processing power and architecture changesCONFIGURATION TESTINGDetermines the effect of configuration changes on the system's performance and behavior
-
Product
Burn-In Test
-
C.C.P. Contact Probes Co., LTD.
Customized Burn-In Test Sockets for temperatures of up to 180°C.
-
Product
Performance Testing
-
All of Xena’s products can be used for performance testing. This typically includes measuring:*the volume of data successfully delivered between two points, usually measured in bits or packets per second*how long it takes data packets to travel between two points in a network or a device, also known as latency*variations in latency – also known as jitter – due to network congestion or other factors*how many data packets fail to reach their destination*if data packets are delivered in a different order from that in which they were sent
-
Product
Test Fixtures-Assemblies
-
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
