-
Product
Adjustable Clamshell Bed of Nails Testers
AdjustaBON Family
-
Designed for quick test development. This fixture can be configured to probe almost any circuit board in just a few hours. Once the perfect test is developed, move this light weight fixture out to the production floor to evaluate your production line test strategy prior to buying permanently drilled test fixtures, or while waiting for your drilled fixtures to be delivered. The AdjustaBON competes with the Flying Prober. There are many advantages over the flying prober. Setup is simple and intuitive and can be much quicker than programming a flying prober. Small size provides versatile bench top operation right where you need it. Maintenance costs are insignificant in comparison. The total cost of this fixture is in many cases less than the yearly maintenance cost of a flying prober. It would be possible to buy one of these fixtures every year for the price paid just to maintain one flying prober and it is about 1/20th the purchase price
-
Product
Hi Potential & Cable Continuity Test Fixture
310HIPOT
-
The most important features of this hipot tester fixture is its safety and ease of use intuitive control functions and durability in a production environment.
-
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
Signal Module
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
EBIRST 78-pin D-type Verification Fixture
93-006-101
Verification Fixture
The 93-006-101 78-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
Product
Materials Measurement Suite
N1500A
-
With Keysight N1500A materials measurement software suite, you can determine the intrinsic electromagnetic properties of many dielectric and magnetic materials. The complete system is based on a versatile Keysight network analyzer which measures the material’s response to RF or microwave energy. The N1500A software controls the network analyzer and calculates results. Depending on the Keysight network analyzer and sample holder or fixture used, frequencies can extend from a few hundred MHz into the low THz.
-
Product
Battery Research Tools
-
PotentioLab battery research tools support coin cell preparation, solid-state battery testing, electrode material evaluation and electrochemical laboratory workflows. Choose fixtures and accessories that improve consistency during sample preparation and cell testing.
-
Product
SoftTest Design Testing Services
-
We are a one-stop turn-key solution provider for the design, development, integration and support for Automated Test Systems. Our capabilities include Functional parametric and non-parametric test systems, intelligent go/no-go gauges, vision systems and a variety of fixtures and adaters to interface with the product under test the most efficient way possible. SofTest Designs can adapt the development architecture to meet the preferences or requirements of our customers in terms of instruments, interfaces and software. With our own in-house machine shop, our development and integration times are greatly reduced optimizing resources and transfering the benefits to our customer's applications.
-
Product
Thunderbolt™
-
SCHILLER AUTOMATION GmbH & Co. KG
Thunderbolt™ test adapters and test fixture kits facilitate Source and Sink compliance testing.
-
Product
Laser Diode Characterization Testing
-
The Yelo Laser Diode Characterization system performs automated characterization of a laser device. The system will allow the operator to load a single packaged Laser device into a TEC controlled fixture mount. Each test station (LIV, Spectrum, Far Field/Beam Divergence) will then automatically align with the Laser Device in a sequential order and perform the automated tests required of each station.
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
Resistivity Cell
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Analog Tensile Testing Machine
-
It can test materials like rubber, wood, plastic, rexins, teflon, cardboard, composites, ferrous metals, non-ferrous metals etc.Wide range of Grips, Attachments & Special fixtures are available to suit varieties of material and shapes. Continuous roll autographic Load Vs Elongation recorder.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Custom Test Fixtures
-
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
Terminal Block
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Test Port Cable, 1 Mm
11500K
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
External Controller
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
Product
Functional Fixtures
-
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
Product
Rotary Table Handler
6000 Series Rotary Handler
-
Rotary table handlers are an excellent choice for PCBA or product – level test, programming, part marking, automatic part rejecting, and vision inspection in order to satisfy manufacturing applications that require high throughput. Rotary table based systems used in production can also help reduce the impact of load and unload times for the operator, because the device-under-test (DUT) automatically moves to the next cell within the station as each DUT is loaded. Circuit Check’s 6000 series handlers are modular, scalable and flexible, supporting high-mix and high-volume production needs. A common application example is to configure a 6000 series as a rotary station to perform simultaneous PCBA bar code scanning, testing, programming and marking, in a pipe-line process which improves throughput requirements. The 6000 series handlers leverage Circuit Check’s unique quick-change fixture drop-in technologies to allow for station modularity and scalability. Production line flexibility is achieved because the 6000 series handler is software and hardware agnostic, enabling adaptability to a variety of applications, and is limited only by the number of stations.
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
Manual Fixture Kit
230354 – CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
Millimeter-Wave Automated Accelerated Reliability Test Systems
nm-Wave AARTS System
-
AARTS fully integrated, automated, turnkey system provides flexibility and accuracy in determining RF and DC performance degradation with aging to predict life expectancy for compound semiconductor devices. Our millimeter-wave Automated Accelerated Reliability Test Systems (AARTS) and fixture solutions are available in standard frequency ranges from 26.5 to 67 GHz.
