Bare Printed Circuit Board Test
SMT and PCB check prior to being populated with components.
-
product
PCI Express A/d Board
AD14-500x4-IRIG
The AD14-500x4-IRIG is a high performance wideband 4-channel 14-bit data single PCIe Gen3 board, that can continuously digitize four wideband signals, with four high linearity A/Ds. A second board version AD14-500x4-K7US-IRIG-B has all of the above features and can additionally be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference, allowing simultaneous synchronized acquisition of data at multiple locations anywhere in the world.
-
product
Heavy Duty Circuit Tester / Jumper
32900
Heavy-duty circuit tester for checking low voltage up to 12 volts. By depressing the red button the tester becomes a jumper for powering electrical components or a ground. The probe, handle, cord and clamp are reinforced for durability. Comes with a strain relief spring on the cord.
-
product
Timing Board #2
TIO-10 #2
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. This board is similar to the Fiber Optic Interface to National Instruments TIO-10 Timing Board #1 only it has more channels connected to fiber optic transmitters and receivers.
-
product
THRU HOLE BARE AND LOADED BOARD TEST PROBES
SERIES 80
MAXIMUM CURRENT: 6 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver with 24 Kt goldplated ID and OD over nickelSPRING: (Standard) Beryllium copper,silver plated. (-1) Stainless steel,silver plated
-
product
3.5" Single Board Computers
Advantech's 3.5" embedded single board computers (SBC) measure 146 x 102 mm feature MIO extension, low-power Intel Atom™,and wide temperature support.
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
3U CPCI Multifunction I/O Board
75G5
NAI's latest generation 3U cPCI Multifunction I/O and Communication Board, the 75G5, can be configured with up to three smart function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
product
6U Processor Board
VP62105
LinkedHope Intelligent Technologies Co.,Ltd.
VP62105 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.VP62105 provides 4 Serial RapidIO (SRIO) x4 links for VPX Data Plane communication, 2 PCI express x8 channel for VPX Expansion Plane communication and 4 Gigabit Ethernet for VPX Control Plane communication. The rich data interchange options enable potential customers a much easier integration path for box level or system level solution designs.
-
product
PC/104 Single Board Computer
PCM-VDX-2
The PCM-VDX-2-512 is a 1GHz, fanless PC/104 single board computer based upon the ultra low power Vortex86DX processor with wired networking capability. This board requires about 6 Watts under full load while operating over an industrial temperature range of -40° to +85°C.
-
-
product
CIRCUIT ENERGIZER
TH852
*Can be used with most 12V mini jump starters with the standard EC5 port*Allows for more portability and freedom from long battery wires*Factory correct terminals means less of a need to back probe*Isolates component from the rest of the circuit which results in less damage to entire wiring/computer modules*No need to remove component for bench test
-
product
MIL-STD-1553 Eight-Channel VME Board
VME-8-1553
The V-Orchestra™ is an eight channel MIL-STD-1553B board which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 32K word of internal RAM.
-
product
110-460V AC/DC 4-way Circuit Tester
1962
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Bright neon AC/DC indicator.*Unique features with convenient pocket up.*Check voltage on 110V, 220V, 277V and 460V AC/DC.*Individual indicator for each voltage range assures reliability.*Reinforced casing and twin flexible test leads store in housing.
-
product
VPX Boards
VPX boards (VITA 46) are ideal for high-performance industrial, defense, scientific research, and telephony systems requiring high-speed I/O with serial fabric interconnect technologies. Carrier cards with PCI Express provide a simple and cost-effective solution for interfacing a PMC or XMC I/O modules to a VPX computer system. VPX FPGA modules offer great flexibility and performance for custom computing applications. Depending on your system’s operating environment, you can select air-cooled, conduction-cooled or Ruggedized Enhanced Design Implementation (REDI VITA 48) versions.
-
product
Fiber Optic Transmitter/Receiver & Repeater Board
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
product
PCI Express A/D Board
AD8-1800 Series - Dual 8 bit, 1.8 GS/s
The AD8-1800 series has one or two 1800 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
product
Circuit Breaker Finder
6504
Peaceful Thriving Enterprise Co Ltd
Circuit Breaker Finder is a multi-function circuit tracer/ identifier. Circuit Breaker Finder identifies circuit breakers without interrupting service.This device is formed by 1x Transmitter and 1x Receiver. There are 3 functions: (1) Socket Tester (Wire Mapping)(2) Circuit Tracing / Identifying(3) Non-Contact Voltage Detecting
-
product
3-28V Cordless Circuit Tester
1948
Peaceful Thriving Enterprise Co Ltd
With CE & UKCA Approvals. Detect voltage from 3V to 28V. No ground wire or clip required. Replaceable long-life alkaline batteries included.(Power supply: SUM5 1.5V X 2 pc). Safe with ECMs, sensors, transducers and air bags.
-
product
Board Drivers
9450-DRV
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
-
product
ARINC 818 Tester
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
RTAX/RTSX Adaptor Boards
Aldec and Microchip have joined together, offering a new, innovative, reprogrammable prototyping solution for Microchip RTAX-S/S and RTSX-SU space-flight system designs. Unlike the traditional OTP (One Time Programmable) anti-fuse space-qualified FPGAs, the Aldec prototype adaptor uses flash-based, Microchip ProASIC®3E FPGA technology, for design prototype re-programmability.
-
product
FMC-HPC ADC Board
FMC123
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Overhead Board
TTC OVH-380-1
Curtiss-Wright Defense Solutions
The TTC OVH-380 is the processor-based controller (overhead) board for the TTC AIM/HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers and terminates the IP stack for Ethernet support.
-
product
Heavy-Duty Circuit Tester With Grounding Adapters
30610
Heavy-duty circuit tester with multiple options for connecting to a ground source. Long, 12’ cord has a quick coupler to securely connect clamp or power outlet plug. Large, strong clamp connects securely. Power outlet plug can always be used to provide ground in the cabin. For testing circuits up to 12 volts.
-
product
Acroname MTM Power Development Board
HIGH POWER. HIGH CURRENT. The MTM Power Development Board allows high power and high current connections to quickly deploy MTM testers.
-
product
I/O Wiring Terminal Boards
ADAM-3900 & PCLD Series
ADAM-3000 series consists of cost-effective, configurable, isolated signal conditioning modules. They are able to operate in harsh environments.
-
product
Demonstration Board
SAMPULSE20x2
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
product
BMP-1-S Board Marker Probe
BMP-1-S
Current Rating (Amps): .05Voltage Rating (VDC): 15Recommended Duty Cycle: 1 sec. On (min.), 5 sec. OffTest Center (mil): 1,000Test Center (mm): 25.40Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Rec. Mounting Hole Size (mil): 468Rec. Mounting Hole Size (mm): 11.89Recommended Drill Size: 15/32 (in) or 11.90 mm
-
product
Signal Processor Board
MS 1532
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
product
3U VPX Single Board Computer
VP32002
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
