-
Product
Transmission Performance/Endurance Test System
-
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
MEMS Testing System
BK3010V2
-
The BaKo BK3010V2 is our updated MEMS Tester, based on our C-Mic tester, the best selling BK3010. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is very easy and can be done in a few minutes. In addition, the new BK3010V2 can be connected to a computer so you can keep and view compiled data and track trends in variations in your C-Mics.
-
Product
MB-OFDM Protocol Test System
WiMedia Explorer 300
-
The WiMedia Explorer 300 is the world's first over-the-air MB-OFDM protocol test system for WiMedia Alliance's Ultrawideband common radio platform, Wireless USB protocol and Bluetooth.
-
Product
Coil Test System
CTS
-
International Electro-Magnetics, Inc.
The system is controlled by a PC using software written in Visual Basic. It offers visually oriented menus that allow easy coil configuration and test set up procedures.
-
Product
Integrated Systems
-
Innerspec’s Integrated Systems are designed to provide automated and semi-automated NDT inspections in factory environments. These systems can incorporate unique sensors, instrumentation, software, as well as customized mechanical devices to integrate the inspection system with other equipment and processes.
-
Product
Thermal Imaging System for Electronics Testing
ETS320
-
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
-
Product
Benchtop Test System
300 Series Benchtop ATE
-
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Automated Hipot Accessory Device
CX-K12
-
Shenzhen Chuangxin Instruments Co., Ltd.
Purpose, To test thin insulating materials for dielectric voltage withstand strength when connected to a hipot tester.
-
Product
Automation Tool for the CMW Platform
CMWrun
-
The R&S®CMW is the leading multistandard UE testing platform used by network operators, test houses, handset vendors and chipset manufacturers worldwide. R&S®CMWrun automation software meets all requirements for executing remote control test sequences on the R&S®CMW for wireless equipment in R&D, quality assurance, production and service. The intuitive graphical user interface of the R&S®CMWrun sequencer software allows easy and straightforward test sequence configuration. No programming and code compilation are needed. At the end of the test, an easy-to-read test report of the limits, test results and verdict is generated.
-
Product
Air Data Test Set System
B511
-
The BRAT Option B511 is an option to the BRAT Test System utilizing Commercial-Off-The-Shelf (COTS) equipment. The system is used to augment the existing BRAT capabilities to test rate of change of altitude or pressure.
-
Product
Stand-Alone Automated ESD Scanner
SmartScan 550
-
API's main hardware platform that most scan technologies can be integrated to this platform. 550 represents the four-axis robot arm size. It is a stand-alone model.:
-
Product
Automated Earthquake Processor
SMARTQuake®
-
Local/distant event discrimination. Event location andmagnitude determination. Moment Tensor Inversion. Source parameters determination. Email notification
-
Product
Automated Stand for Magnetic Luminescent Control of Railway Wheels
-
The amount of information processed and time constraints required the creation of a multi-level distributed image processing system based on National Instruments Compact Vision System controllers, industrial computers and workstations. During the control process, the wheel is watered with a magnetic-luminescent emulsion, magnetized and exposed to ultraviolet radiation. As a result, the emulsion deposited on the defects glows in the visible range (yellow-green light). Eleven FireWire (IEEE 1394) color cameras with a resolution of 1280 x 1024 are used to scan the wheel surface. In one iteration, they completely cover a 20-degree sector of the wheel.
-
Product
Medical System
Sentinel I
-
Chroma Systems Solutions, Inc.
The Sentinel I System provides fully automated Electrical Safety Testing to IEC/EN/UL/CSA 60601-1. This system is ideal for testing medical products with one or no patient connections or low volume production where operators can manually change leads between different patient connections. This is a 5 in one Hipot test system that can test Hipot, Ground Bond, Insulation Resistance, Patient Leakage, Earth Line Leakage, Enclosure Leakage and Patient Auxiliary Leakage.
-
Product
Assembly Systems
-
Easily add automation to your assembly process. Free operator hands and eliminate the need to manually handle screws. The A-50 units are modular...a simple rail change and readjustment are all that are necessary to use a variety of screw sizes.
-
Product
TOV Test System
-
Shanghai Guantu Technology Co., Ltd.
1. Safety protection: traffic light indication status, emergency stop and interlocking of the test product door2. Equipped with a computer, set the TOV power supply parameters through the software interface, and automatically test3. Equipped with alarm function, equipped with emergency brake switch, equipped with safety cover and door switch4. The computer interface displays real-time voltage and current data5. Automatically draw voltage and current waveforms, and can save the waveforms as BMP format pictures, which is convenient for editing experiment reports.6. Automatically record test time, test current, test voltage, etc., and save the recorded data to files7. Installation method: cabinet installation.
-
Product
Bus Management Test System
-
Solution to test redundant Architecture of BMUComprehensive test system performing tests of > 3000 I/O's Special test circuits using hybrid / ceramic components to operate in Thermovac chamber Tests various subsystem functionalities like, AOCS, Sensor Electronics, Telemetry, Tele-command with Self test and application test software
-
Product
AFDXEnd System
A664 Pro (PMC)
-
The AFDXEnd System A664 Pro board supports speeds up to 100 Mbit/s and is certifiable to civil aerospace standards. This PMC card supports rate-constrained traffic shaping to ensure bounded latency and jitter for Deterministic Ethernet networking, as described in the ARINC 664 part 7 standard. The network board can be used for production system integration and provides redundancy management as well as an IP/UDP profiled communication layer fully implemented in hardware.
-
Product
System Controller
T96
-
The T96 Controller is a universal controller supporting all the standard Linkam stage families, providing complete control of the system.The T96 can be controlled through the LINK software using the USB interface or the high resolution LinkPad, an ergonomic touch screen display, which enables the user to quickly enter experimental parameters for the hotstage.
-
Product
V4 Marine Communications System - V4 NAVTEX Test System
-
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
Product
Telemetering System
ZET 7172
-
ZET 7172 telemetering system is used to provide wireless access to the instrument line segment using radio channel.
-
Product
Lithography Systems
-
When it comes to shaping what a chip can do, lithography systems lead the way by transferring intricate circuit designs onto substrates with unmatched precision. From prototyping to high-volume manufacturing, these tools define the geometry of modern microchips, as well performance.
-
Product
25-Seven Systems
-
The resulting product—Audio Time Manager—became radio’s preeminent solution for real-time compression and time-shifting, and has been used at some of the biggest talk stations in the world. Always on the bleeding edge, 25-Seven then reinvented the profanity delay with Program Delay Manager, adding the unprecedented capability to capture objectionable live content for future review. Now, 25-Seven Systems specializes in audio technologies and products that address unique problems in the industry. Most recently, 25-Seven has produced one of the most disruptive technologies in broadcast history—the Voltair line of water-marking enhancement products, which became one of the hottest and most game-changing products in the industry
-
Product
PCIe 5.0 Test Platform
PXP-500A
Test Platform
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
Product
Measurement Systems
-
Systems used in the process of associating numbers with physical quantities and phenomena.
-
Product
Power Device Test Systems
-
Power semiconductors are devices that control electric power, and are used in automobiles and a wide range of electrical products. Our power semiconductor test systems, developed and provided by CREA, an Advantest Group company, specialize in testing power semiconductors that handle high voltages and large currents, and have special safety features for this purpose.
-
Product
Tracker for Testing CPV Module Systems
-
The tracking precision of our biaxial tracker is better than ±1° on each axis, with an option for ±0.1° precision. This makes the tracker ideal for testing concentrating PV modules. The software runs all required tests for angle-dependent testing of PV modules according to IEC 62108.
-
Product
Test Analysis for Land Seismic Systems
Testif-i Land
-
Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.
-
Product
Software & Systems
-
Through the use of the correct software and systems you are able to easily configure specific scanners to work at their peak performance in collecting data from codes determined to be found on the fast moving automated systems such as 1D and 2D codes including Data Matrix, QR and DPM (Direct Parts Marking) codes. Datalogic’s innovative supervisory software solutions monitor operational activities of stationary industrial scanners by a web browser-based interface. Data is collected from different scan points through an Ethernet TCP/IP network then displays the received information flow as a visual onscreen readout. The ability for real-time analysis and corrections results in increased throughput and decreased downtime on the line.
