Earth Leakage Circuit Breaker Testers
test trip time and trip current values.
-
Product
Ground Bond Tester
264
-
Our 264 Model makes Ground Bond / High Continuity Testing simple with 40 Amps of current to satisfy your NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 264 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
Product
Protocol Conformance Tester
TS-PCT
-
The R&S®TS PCT is a compact full range protocol conformance test solution in line with GCF and PTCRB requirements. It supports the entire device certification process for protocol testing and can be extended to operator acceptance testing by adding software.
-
Product
Automatic Circuit Breaker Tester
GDGK-306
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Test standard: IEC622712) Closing and opening time measurement of 12 channels3) Max difference of closing or opening time measurement of three phases4) C-O and O-C time measurement5) Rated operation sequence test6) Bounce time and frequency measurement of breaker closing7) Circuit breaker closing and opening speed measurement8) Travel-time, Coil current-time curve of circuit breaker operation measurement9) Travel and clearance of circuit breaker measurement10) Variable DC circuit breaker operation power supply11) Closing arc resistance value and connected time measurement12) Closing time and opening time of graphite circuit breaker measurement13) Print test results by internal micro printers
-
Product
Pocket Conductivity Testers
-
Labodam pocket conductivity testers are equipped with platinum sensors and 1 point brush calibration system. These easy to use pocket conductivity meters come with waterproof design features for protection against harsh conditions. The conductivity meters can be used for measuring the conductivity of drinking water, waste water, brine water, and liquids with high, low conductivity.
-
Product
SART Tester
-
The International Marine Organization states that all GMDSS equipment (including SARTs) should be periodically maintained and verified to meet all the performance requirements. In case of test failure, ships may be detained in a port under SOLAS regulation IV/15.8.The 9GHz Search and rescue radar transponder (radar-SART) is indispensable safety device and it must be checked regularly or annually during radio inspection.The purpose of an annual testing is to determine that SART is operational as defined in appropriate performance standards for Survival Craft Radar Transponders for use in Search and Rescue Operations, IMO Resolution A.802 (19).
-
Product
3 Wire (Analogue) Earth Resistance Tester
2705 ER
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
Product
Portable Hardness Tester
PHT-1700
-
Loaded with features, this economically priced hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with the universal D impact device, calibrated test block and rugged carry case.
-
Product
Emission Testers
-
Maschinenbau Haldenwang GmbH & Co. KG.
A device that monitors the composition of the flue gas of a boiler heating unit to determine if the mixture of air and fuel is at the proper ratio for maximum heat output.
-
Product
Deadweight Testers & Gauges
-
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area.
-
Product
LD/LED ESD Tester
-
Hanwa Electronic Ind. Co.,Ltd.
Performs automatic destructive evaluation of Lazer-Power.
-
Product
Winding Resistance Tester
JYR20S/10S
-
DC winding resistance testing is regarded as another essential routine screening tool. It indicates problems such as loose, defective or incorrect connections, which cause enough transformer failures each year to be regarded as a failure category of its own.
-
Product
Battery Testers
-
When diagnosing a starting system issue, it is important to pinpoint the exact source of the problem to avoid warranty/replacement of the wrong part, reduce vehicle comebacks and maintain customer satisfaction. BA Series testers provide the detailed data needed to make the right call. Model Nos. BA5 and BA7 are economical enough to be used as triage testers at busy repair facilities. Put them in the hands of every tech in the shop and watch efficiency skyrocket.
-
Product
6-12V Heavy Duty Circuit Tester
1649
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. Quickly and safely tests high and low voltages on all vehicle voltages, including computerized engine.
-
Product
Circuit Breaker Analyzer
CBA 1000
-
CBA 1000 circuit breaker timing test equipment is a reliable and very accurate operating device for the maintenance and commissioning of circuit breakers in medium and high voltage substation. It can perform static and dynamic contact resistance measurement and it’s an accurate timing speed and motion analyzer.
-
Product
Infusion Pump Tester
IN-600
-
Measuring and testing device for checking infusion pumps according to IEC 60601-2-24.
-
Product
Insulation Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
Product
RRH/RRH Installation Tester
Integris 2000
-
Field installation teams for RRH s have a difficult task in validating the installation for proper cabling and RRH operation. This is because the BBU that connects to the RRH is not present during the RRH installation, making it impossible to truly know if the tower cabling and RRH have been installed properly.
-
Product
Cut Susceptibility Tester
-
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
Product
Teraohmmeter/IR Tester
98x
-
The new 981i and 983i Teraohmmeters are designed to tackle the toughest High Resistance measurement applications. Demanding applications that most other IR testers won’t measure up to. So when it’s time to test higher voltage IR values like today’s electric vehicle systems and higher voltage solar arrays — look to Vitrek to deliver the IR tester you need for your production line.
-
Product
Voltage Detectors & Testers
-
Non-contact AC voltage detector quickly checks for the presence of live voltage on wiring and electrical devices. Features a built-in flashlight for added convenience.
-
-
Product
Electrolytic Capacitor Leakage Current Meter
TH2686C
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test voltage: 0-200V, 0-500V ■ Voltage accuracy: 2% set value + 2 words ■ Measuring range: 0-30mA, 10 gears ■ Current accuracy: 2% of reading +0.5 grid
-
Product
Personal SerDes Testers
C Series
-
Everything you need to develop and verify your high-speed digital algorithms is contained in these ultra-portable test instruments. They will forever change the way you think about developing and verifying Gbps digital and mixed-signal algorithms, and they will allow you to measure signals in ways that were not possible in the past. Each personalized SerDes tester is equivalent to multiple hardware platforms, containing everything that you need to make high-performance measurements like bit error rate testing, signal generation, and signal measurement.
-
Product
Memory Tester
RAMCHECK
-
RAMCHECK is our most advanced memory tester and is the latest in our product line. Highly modular and user friendly, it redefines the capabilities of an affordable and portable ram checker.
-
Product
Air Data Tester
PS131bII
-
Aircraft Development Industries cc
The Model PS131bII is an advanced Air Data - Pitot Static Tester, which drastically simplifies the process of testing the aircraft's Pitot and Static system. The test altitudes, airspeeds and vertical speeds are achieved by simply typing in the values and the tester will automatically do the rest. The Model PS131bII is a completely digital, microprocessor-controlled device using all solid state transducers and components.
-
Product
B6-48V Digital Circuit Tester Kits
1675
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12, 24 and 48V systems. Kit packed in a deluxe blow mold case.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Flexible Printed Circuits (FPC)/Flat Flex Cables (FFC) Connectors
-
Panasonic Industrial Devices Sales Company of America
Connectors for flexible printed circuits (FPC) and flat flex cables (FFC). Height 0.9 to 1.8mm. Pitch between terminals 0.3/0.5mm. FPC / FFC is a one-piece type Connector that makes the connection with a directly-inserted FFC or FPC and locks it by means of a lever. This type of Connector can be used in a wide range of digital devices when a low profile or the horizontal insertion of flex is required.
-
Product
Hipot Testers
Hypot® Series
-
The Hypot Series sets the standard for safety and efficiency in production line Hipot Testing. Whether your application requires AC Withstand tests, DC Withstand tests, or Insulation Resistance tests, The Hypot Series provides innovations that will allow you to begin achieving best practices for safety and efficiency without the need for an expensive automated test system or connection to a PC. You can even connect the Hypot Series with the HYAMP Series to form a seamless safety compliance system for Hipot and Ground Bond Testing.
-
Product
Hot Tack Tester
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
GBPI Hot Tack Tester To test the sticking strength of packaging films after heat sealed with different temperature, pressure and time. It simulates the use of packaging bag and makes impact experiment on the part of hot tack.
