VXI Mainframes
-
Product
Interface Technology Style VXI Module Shield Kits
-
*Encloses Interface Technology style, slotted-edge, C-size PC boards All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. * All kits are available with customized front panels and side shields.
-
Product
13-slot VXI Chassis
-
The 13-slot VXI crate is designed for use in modular measurement information systems based on the VXI version of the standard. The 13-slot VXI crate is designed to accommodate the system module, in the first slot, and VXI instrumental modules placed in the remaining slots, to provide their power supply, as well as to provide information interconnection via the VXIbus bus between the modules and with the control computer. The chassis meets the requirements of GOST R 51884-2002 and the document System Specification VXI-1 Revision 1.4.
-
Product
VXI Register-based Interface Board
-
VXI Register Interface mates with user's PCB to form a B or C-size module.
-
Product
Blank Module, VXI Receiver, 2 Module Positions
510104178
Blank Module
Blank Modules are made from black anodized aluminum or black PEI thermoplastic and are for unused module slots. The Blank Shielding Module fills a module slot and shields signals between the modules. Blank Modules fit either ITA or Receiver positions.
-
Product
ITA, 9050, 50 Module, VXI And Discrete Wiring, VDATS
410104721
ITA
Customized VDATS 9050 VXI ITA frame with 3 bearings per side.
-
Product
VXI Register Interface Board
VXI-5524A-3
-
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
Product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
-
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
Standard VXI Module Shield Kits With Address Switch Opening
-
* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Clamshell design fits C-size modules with 96-pin connectors.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Address switch opening on component side shield.* Complimentary layout support includes PCB design template and CAD layout files.
-
Product
3-slot VXI Chassis
-
The 3-slot VXI compact crate is designed for use in modular VXI measurement information systems.
-
Product
VXI 11 Slot C-Size
-
High-Performance 11 Slot C Size VXI Monolithic Backplane with High Current Din Conncectors.
-
Product
VXI Backplanes
-
VXI is a prime example of the old saying, “if it isn’t broken, don’t fix it.” Since the late 1980’s, VXI has been a trusted standard in the world of testing solutions as a more compact and robust predecessor of the GPIB standard. Arising initially to soothe the need for a more compact and integral open testing standard, VXI is still as necessary and impactful as it was more than 30 years ago.
-
Product
VXI 11 Slot C-Size
-
High-Performance 11 Slot C Size VXI Monolithic Backplane with High Current Din Conncectors.
-
Product
Digitizer with two 125 MS/s, 14-Bit Channels, Recommended for VXI Systems
6084-2105
Digitizer
The Astronics 6084-2105 digitizer includes two 125MS/s, 14-bit digitizer channels and is recommended for VXI systems that need either improved accuracy or replacement of an obsolete instrument. Wide dynamic sampling, a powerful acquisition engine, and excellent AC/DC performance ensure an upgrade for your VXI system that will preserve your legacy investment for years to come.Key features include:Dual 14-bit digitizers for SE or DIFF operation at sample rates up to 125 MS/sDC accuracy of 0.15% ± 800 µV on low voltage rangesSFDR 80 dB at 1 MHz Wide input ranges from 0.25 Vpk to 256 VpkPerformance upgrade or replacement for existing VXI applications Pre- and post-triggering availableWaveform storage of 32 M samples per channel
-
Product
Instrument Mainframe
PI-11008
-
The PI-11008 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
VXI Prototyping Kits For RF Modules, Analog And Logic Circuits
-
• VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.
-
Product
Switch Mainframe
SW1001
-
Switch between voltmeter and battery tester while testing. 66 channels max. (2-wire) to 18 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
High Performance VXI Chassis for Military ATE Systems
1261B Series
Chassis
The 1261B high-performance VXI chassis serves as the standard for most military ATE systems. All 1261B chassis include full-power protection features such as overvoltage and overcurrent protection, and also incorporate a quick-check diagnostic connector to verify performance of power supply voltages, currents and specific VXI signals.
-
Product
VXI Digital Multimeters
Digital Multimeter
Maximize the use of your legacy test systems with our line of high-performance VXI digital multimeters.
-
Product
16 Channel Mainframe
Synergy CS
-
The Synergy CS mainframe further extends the available channel count supporting up to 16 input modules in a benchtop or rackmount configuration. The Synergy CS can be configured with or without internal display.
-
Product
6U Power Supply Mainframe. Accepts Two Programmable Power Modules
GX7400A
Power Module
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
Product
VXI IP Carrier Module
DP-VXI-5124
-
The Data Patterns DP-VXI-5124 is a VXI 'C' size Carrier Board, which occupies a single slot in the VXI system. The module is a register based device with A16/A24/A32 address space and has interrupter capability. The carrier board's VXI bus interface is used to program and monitor the carrier board registers for configuration and control of the board. The VXI bus interface is also used to communicate with and control the external devices that are connected to an IP modules field I/O signals.
-
Product
Enclosure, 9050, 50 Module, VXI Sloped
410114359
Enclosure
Enclosure, 9050, 50 Module, VXI Sloped
-
Product
Switch Mainframe
SW1002
-
Switch between voltmeter and battery tester while testing. 264 channels max. (2-wire) to 72 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
VXI Rev 4.0 Module Shield Kits
-
*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
-
Product
ITA, 9050, 50 Module, VXI and Discrete Wiring, Double Tier
410104538
ITA
The 50 module ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC front or rear mount enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration.
-
Product
ITA, 9075, 50 Module, VXI
410104276
ITA
ITA, 9075, 50 Module, VXIThis ITA is designed for the 9075, but only has 50 module slots and is designed for the bottom 2 tiers.
-
Product
9050, 50 Module, Receiver, VXI and Discrete Wiring, Double Tier
310104248
Receiver
This 50 module receiver is rugged and designed to accommodate high I/O. With high contact point availability, the 9050 receiver is suited for larger test and measurement systems. The top tier accommodates VXI instruments and accepts VPC's interconnect adapters with the bottom tier for discrete wiring.
-
-
Product
6-Slot C-Size VXI Chassis
1264 Series
Chassis
The Astronics 1264C is a low-cost, 6-slot, C-size VXI chassis, designed and built with ISO-9001 certified quality. This chassis includes performance features normally found only in high-end, 13-slot chassis.
