Electromagnet
See Also: Electromagnetic
-
Product
Compact Range Reflectors
-
The company advances every aspect of reflector system development—from design and fabrication to surface characterization, transportation, installation, and electromagnetic evaluation.
-
Product
Impulse Current Test Systems
-
Fivestar HV Testing Equipment Co., Ltd.
Impulse current test systems are mainly used for testing transmission and distribution systems against the effects of direct or indirect lightning strokes or against electromagnetic interference effects. Primary application of impulse current test systems is the testing of surge arresters, nowadays mainly of the metal-oxide type (MOA) and surge protection devices (SPD). Now they are also widely used to test vehicles, aircrafts, and military applications.
-
Product
Magnetic Pole Indicator
-
identification of the field-direction of a magnet (north - south). It simply ascertains, fast and reliably the polarity of permanent magnets and electromagnets. This reliable device is simply to be served. It is indispensable for all industrial areas and fields of investigation which deal with magnetic applications.
-
Product
Vibration Testing
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood , a 23 years of professional Vibration Test System for Automotive parts, vibration table, vibration machine, Electromagnetic vibration table, Vibration Test Chamber manufacturers
-
Product
Electromagnetic Flowmeter for conductive liquids
Picomag
-
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
Product
Compact Accelerometer (Shock Meter)
AP2019
-
Can be used as shock sensors in equipment diagnostic systems; Combination of high axial sensibility, intrinsic frequency and shock resistance; Low sensitivity to electromagnetic fields; Low intrinsic noise level.
-
Product
Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCI-1564
-
32 bit, 33 MHz, PCI interfaceInput channels32 isolated digital input channels, 24 V, incl. 16 interruptible and 3 fast counter inputsInput channels organised in 4 groups of 8 channels, each group has its own ground lineVoltage reversal protectionAll inputs are filteredOutput channels32 isolated digital output channels, 10 to 36 VOutput current per channel 500 mAWatchdog for resetting the outputs to "0"After power/ON the outputs are reset to ì0îShort-circuit current for 16 outputs ~ 3 AShort-circuit current for 32 outputs ~ 6 AShort-circuit current per output ~1.5 AElectronic fuseOvertemperature and overvoltage protection24 V power outputs with protection diodes and filtersSpecial output capacitors minimise electromagnetic emissionsExternal 24 V supply screened through a protection circuitryShutdown logic when the external supply voltage drops unter 5 V
-
Product
Excimer Lasers
-
Powerful and versatile light sources in the UV range of the electromagnetic spectrum. Because of their cold ablation and short wavelength, excimer lasers are used for countless applications.
-
Product
Qwiic Spectral Sensor
AS7341
-
The AS7341 is an 11-channel spectral sensor from AMS that covers wavelengths between 350nm to 1000nm. It features eight channels that span the visible spectrum and there's a channel for Near IR, clear, and flicker detection up to 2kHz. Point a spectral sensor at an object and it measures the reflected or absorbed electromagnetic wavelengths.
-
Product
Electromagnetic Ammeters And Voltmeters Fb-1, AC Electric Current, AC Voltage
-
ELECTROMAGNETIC DEVICES FOR MEASUREMENT OF ACTIVE VOLTAGE AND ACTIVE CURRENT.
-
Product
TWTs - Traveling Wave Tubes
-
Travelling wave tubes remains a valuable type of amplifier for high output power in the microwave range. Its main advantages are of high output power, big bandwidth-duration and reliability. Insight Product Co. offers TWT packaged tubes providing output power from tens to several hundred watt in a continuous mode and to 1.5-2.0 kw in a pulse mode, and frequency bandwidth of 1.5 octaves. TWT applications include satelite communications (transponders) both on land and on satelite installations, radio relay communication lines, electromagnetic compatability (EMC) testing industry for immunity testing of electronic devices, and radars (maritime, weather, airplanes, land).
-
Product
Magnetic Resonance Instruments
-
Integrated Dynamics Engineering
MRI systems represent a significant investment. As magnetic resonance images can be distorted by electromagnetic fields, frequently the location is isolated by passive shielding to somewhat insulate the detectors from image distorting EMI. But for a fraction of the cost of the machine an active EMI compensation can fully protect the image from damaging fields generated by other electrical equipment, passing traffic, elevators or other nearby equipment.
-
Product
EMI/EMC Testing
-
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
Waveguide Twists
-
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
Electromagnetic Immunity Scanner
SmartScan 350
-
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
Product
Inductive Sensors
-
In general, inductive proximity switches consist of four basic elements: a coil, an oscillator, a threshold switch and an output stage with short-circuit protection.The oscillator generates a high frequency, electromagnetic alternating field which is emitted from the active face of the coil.Eddy currents are induced in a metal object that enters this field. These eddy currents draw energy from both the electromagnetic field and from the oscillator which is consequently attenuated.The more energy taken the closer the metal object moves towards the active face. The threshold switch switches on the output stage at a defined attenuation value.In proximity switches with a DC voltage supply, this switch is designed as an NPN transistor which switches the connected load to the negative pole or as a PNP transistor which switches the load to the positive pole. The output stage is a thyristor or a triac in AC voltage switches.
-
Product
Consulting Services
-
Standards and Regulatory Management. Standards Development. Regulatory (FCC, FDA, Access Board). Areas of Technical Excellence: Electromagnetic Compatibility, Disability Access, Wireless Requirements, RF Safety (EMF & SAR), Product Compliance, Quality & Conformity Systems, Measurement of Electromagnetic Fields. Training - We offer a variety of course in various areas of compliance and technology. We also provide custom training, tailored to your needs, in our areas of expertise.
-
Product
EN 50155 16-Port Ethernet Switches
EKI-9516 Series
-
a high-density, ruggedized networking device specifically certified for use in railway, onboard train, and harsh industrial environments. It features 16 physical ports to connect multiple devices (such as IP cameras, Wi-Fi access points, or passenger infotainment systems) and adheres to strict European standards for electromagnetic compatibility, temperature, shock, and vibration.
-
Product
Off-Air Testing Products
-
Understanding the challenges of the Electromagnetic Spectrum is paramount for Engineers that are charged with the design, characterization, validation of modern RF systems such as Communications Systems, RADAR Systems, and Electronic Warfare Systems.
-
Product
Hand-In Type Electromagnetic Anechoic Box (Shield Box)
MY3710HS
-
Higher shielding performance than MY371080dB. Suitable for weak electric field resistance test, out-of-service test or digital forensics for mobile phone, smart phone or tablet terminal! DUT can be operated directly with bare hands while placing it in the box and looking at the inside from the shield window.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
DIN-rail Embedded System
-
Axiomtek’s DIN-rail fanless embedded systems are suitable for intelligent computing and communication solutions in mission critical environments, such as power plant automation and facility monitoring systems. Axiomtek’s DIN-rail fanless embedded PCs are rugged and have passed heavy industrial EMI/EMS (Electro-Magnetic Susceptibility/ Electro-Magnetic Interference) tests for reliability in hazardous environments.
-
Product
Stripline Automotive 10KHz-30MHz 50 Ohm
STPL-30
-
The GTEMCELL STPL-30 Stripline is designed to produce high electric fields over a controlled bandwidth. It is used to perform EMC measurements according to automotive and aerospace standards in order totest the immunity of automotive and aircraft equipment to radiated electromagnetic fields.The STPL-30 uses a dual-sided tapered adjustable feed design into a tunable transmission line.
-
Product
ESD Event Detector
Novx MiniPulse
-
Simco-Ion's Novx MiniPulse ESD Event Detector is designed for tool and process monitoring. This affordable, small footprint embeddable monitor has been developed to warn of product damage risks at the point of electrostatic discharge. The MiniPulse uses time domain and threshold discrimination to detect pulse electromagnetic energy. Through the use of specific antenna configurations and placement, the MiniPulse can provide ESD event detection for well-defined small areas.
-
Product
FCC Part 15 Testing & Certification
-
FCC Part 15 is the section of Title 47 of the Code of Federal Regulations that sets limitations on the amount of electromagnetic interference allowed from digital and electronic devices. FCC Part 15 also covers technical specifications, administrative requirements and other conditions relating to the marketing of FCC Part 15 devices.
-
Product
Electromagnetic Environment Simulators
A2PATS® Products
-
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
Product
EMF/ RF Field Strength Meter
-
Designed for measuring and monitoring Radio–Frequency electromagnetic field strength.
-
Product
Emergency Conditions Testing
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
