Salt Spray Chambers
splash a condensed salt water solution on surfaces testing their corrosion resistance.
See Also: Salt Spray, Chambers
-
Product
Dust Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sand Dust chamber provide an environment to test the exposure of automotive and electronic components to concentrated levels of dust in order to validate product seal integrity.
-
Product
Spray Equipment
-
Engineered for the most demanding automotive and industrial refinishing bodyshops through to the smallest independent workshop - whatever your spraying requirements, Sagola has the gun you need.
-
Product
IP X7, X8 - Waterproof Test Chamber
-
The IP X7 and IP X8 test equipment simulates the water immersion environment to test the water resistance and sealing of the samples during storage, transportation and usage. It is widely applied to electrical and electronic products, lamps and lanterns, electrical cabinet, electrical components, automobile, motorcycle and its spare parts and other products. It provides the basis to improve the performance of the products.
-
Product
Corrosion Test Chamber
CME SF-CCT
-
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
Product
Weather Meter For Spray Applications
3550AG
-
Avoid spray drift and maximize application results with this portable and connected handheld weather meter. Off-target pesticide drift can not only cause damage to nearby vulnerable crops but also pose a serious threat to people, livestock, wildlife, and the surrounding community.
-
Product
High Frequency Chambers
-
Specialized, shielded rooms designed to absorb electromagnetic reflections.
-
Product
Cyclic Corrosion Test Chambers
CCT
-
Cyclic Corrosion Test Chambers are used throughout the automotive, aerospace, fasteners, electronics, paints and coating industries.
-
Product
Walk-in Integral Chambers
FL-I
-
Bemco integral chambers include a heliarc welded, 300 Series stainless steel inner liner, fiberglass insulation, and a structural steel supported, carbon steel outer case finished in Bemco blue. Stainless steel and other exterior materials are also available. No asbestos is used in chamber construction.
-
Product
Solar Spectrum Test Chambers
-
Thermoregulation system Solar simulation chamber made of a metallic frame and insulation cover panels The test chamber can be easily opened with one hand The height of the sample carrier can also be varied to ensure optimal irradiation of the various samples Corrosion resistant Stainless steel construction Air-cooled refrigeration unit Micro-processor monitoring and control unit Aerosol-free humidification and dehumidification Psychrometric humidity measuring system
-
Product
Temperature Chambers & Humidity Chambers
-
Temperature and humidity test chambers are available as standard products in a variety of sizes to suit your needs. Our environmental test chambers are often used for steady-state stability testing, basic temperature cycling and accelerated stress testing.
-
Product
Walk-In Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Energy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions. The technology is based on Danish Danfoss' ETS series of electronic expansion valves, which can be used to smoothly adjust the cooling capacity for different cooling capacity requirements, that is, to achieve the compressor cooling capacity adjustment when different cooling rate requirements are met.
-
Product
Military-Grade 4-In-One Temp/Humidity/Vibration/Pressure Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Integral structure, the internal overall TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism. - The use of Chinese color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box independently developed special software, with automatic, intelligent, human control and other characteristics. - Control mode: constant operation mode, program operation mode. - TEST EQ patent "Cold and heat balance technology”, low temperature constant temperature season can be more than 30%. - Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions. - The humidification system adopts TEST EQ patented technology. - The lift structure through the lift (wireless remote control) up and down and left and right movement to match the shaking table horizontal or vertical table, comprehensive performance test. - Gantry structure: Through worm gear (wireless remote control), the studio box is lifted up and down and the gantry is moved around to match the horizontal or vertical table of the shaking table, and the comprehensive performance is tested. - The seal of temperature and humidity box and vibration table adopts TESTEQ patent technology low pressure flexible connection device. - Pressure mode: internal pressure type or external pressure type. - Vacuum system: the world famous brand ""Laibao"" or ""Jitis"". - Configure RJ45 communication interface, remote control system (open data transmission protocol support Modbus/OPC). - Surface electrostatic powder spraying; chamber color ""TESTEQ White "", controller panel color ""TESTEQ Blue "".- TESTEQ patent cold well adsorption anti-condensation function (optional).
-
Product
Climatic Test Chamber
-
HIACC Engineering & Services Pvt. Ltd.
Optimised heating & cooling system offers higher performance & energy efficiency. The test chamber can be customised suiting to different test standards. It comes with larger viewing window, ports for live specimen testing, visual alarm system, improved mobility and smaller footprint.
-
Product
Constant Climate Chamber
HPP
-
Temperature range up to +70 C 3 model sizes 110, 260, 750 1 model variant: TwinDISPLAY Digitally controlled active humidification and dehumidification up to 90% Double doors as standard: Prevention of contamination and drops or rises in temperature, and at the same time an optimal view of the sensitive load through wide-area interior glass doors
-
Product
UV Weather Resistance Test Chamber
-
This series is applicable for the sunlight resistant test of nonmetallic materials and aging test of artificial light source.
-
Product
TTC-1 Tracking Test Chamber
TTC-1
-
It is according to IEC60695 and IEC60112 (GB4207), the Tracking Test Chamber TTC-1 is intended for determining the degree of protection against formation of conducting paths in solid insulating materials, due to the electric stress and electrolytic contamination of the surface. This method simulates tracking currents on insulation material by providing drops between electrodes. During the process of normal use, insulating material may be exposed to moisture and dirt, if conductive, may cause stress and fire hazard.
-
Product
Antenna Test Systems and OTA Chambers
-
With our well-established experience in innovative solutions based on top-quality engineering, Rohde & Schwarz provides you with leading antenna test systems and OTA chambers.
-
Product
Custom Test Chambers
-
Test chambers for accurate and repeatable electroacoustic measurements
-
Product
Temperature Test Chambers & Humidity Test Chambers
-
Weiss Technik Temperature & Humidity test chambers offer many pre-engineered and custom sizes to fit your exact testing requirements. Available models include a wide range of temperature ramp rates, humidity levels, and many standard and optional features including temperature cycling, steady-state testing, and fast change rate.
-
Product
UL94 Combustion Chamber, IE60695vFlammability Tester
CX-S16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Horizontal Vertical Flame Tester is a comprehensive test instrument whick strickly designed according to Standard IEC60695, GB5169, UL94 and can meet the relative standard's requirements. It's mainly used to test the flammability of plastic and other nonmetalloid parts specimen to evaluate fire hazardous degree of accidental burning caused by the material.
-
Product
Swivel Sprays
1188
-
The Parker Conflow Code 1188 - swivel spray is an easily controllable, multi-directional spray unit used for dust suppression or cleaning of chutes in mining or quarrying applications
-
Product
Temperature and Humidity Chamber
GT-C52
-
Temperature and Humidity Chamber is for conditioning of samples prior to testing. It also can be used for a variety of material of high - low temperature alternating test. The test temperature, humidity, time can be programmed. Provides conditions of temperature from -40 degree to +150 degrees and of humidity 20% to 98%.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Double Function Tester with Shielded HF Test Chambers
End-of-line Tester UTP 9010 RF
-
The UTP Series 9010 is a scalable test series available in a variety of feature-rich variants and many designs. The UTP 9010 RF function tester shown here as an example is suitable for tests with a medium number of channels and complexity. It is designed for parallel testing of two or more test items. The measuring instruments used are used alternately for several test items. Due to its compact design and construction as a modular system, this powerful tester can easily be expanded to larger numbers of channels.The integrated HF test chamber UTP 5070 developed by NOFFZ allows an independent shielded test. It can be operated manually or fully automatically by a robot .The basic version of the UTP 9010 series is an ideal system for functional and end-of-line tests and is already preconfigured for this purpose. The RF tester presented in the example is used in particular to test infotainment and eCall modules in the vehicle as well as IoT products with wireless technologies.
-
Product
Walk-In Solar Spectrum Test Chamber
-
WEIBER walk in Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. It is also called Walk in Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Solar spectrum chamber also known as Walk in Solar Simulation Test Chamber
-
Product
Altitude Chamber
FA Series
-
Altitude Test Chambers combine temperature and altitude environments with optional humidity for simultaneous environmental testing. An Altitude Chamber allows users to control the test chamber temperature while subjecting the product under test to various levels of altitude 50,000 to 100,000 feet. This combination of elements allows precise simulation of real-life conditions a product might encounter at various altitude levels.
-
Product
Compact Range Chambers
-
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
Product
Double-deck High Temperature Aging Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High Temperature Aging Test Chamber is widely used to the aging test for electronic products, solar panel, plastic products, especially for battery temperature aging test.
-
Product
OTA Chamber for 5G NR mmWave Signals
ATS1800C
-
The R&S®ATS1800C CATR based 5G NR mmWave test chamber provides the ideal environment for testing 5G FR2 antennas, modules and devices over the air (OTA) from R&D to conformance. With its small footprint and wide frequency range, the R&S®ATS1800C offers great functionality and test coverage in a very small space. With its flexibility and broad range of extension options, the R&S®ATS1800C offers a solid and future-proof environment for your FR2 testing needs.
-
Product
Sulphur Dioxide Test Chambers
-
The Sulphur Dioxide Test Chambers from Weiber are Corrosion Test Chambers used for testing the corrosion resistance of metallic surfaces and outer protective layer of coatings. They are used to create a highly corrosive environment rich in corrosive gases and natural humid conditions to induce accelerated corrosion in protective coatings of machines and equipments, electrical items, electronic parts and components, mechanical constructions, automobile and aircraft parts and components etc. Since the corrosive action of Sulphur dioxide also depends on specific temperature and humidity conditions and the presence of other contaminants, the Weiber Sulphur Dioxide Test Chambers are designed to create optimal conditions of temperature and humidity and also make provisions for introducing impurities and contaminants. These equipments operate across a wide temperature range, creating variations in the working temperature to mimic a natural weathering environment.
