Transceiver Test
-
Product
Transceiver Testing
-
Family of RF test systems designed for transceiver testing. Designed for radio-to-radio testing in a closed mesh network. Step attenuators allow you to dynamically fade up/down the RF signal between radios. These Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted remote commands.
-
Product
Benchtop Femtosecond/Picosecond Lasers and Amplifiers
-
The systems feature a portable design with user-friendly front panel control knobs for adjustment of output parameters, such as power, pulse width and repetition rate. With wavelength options of 780 nm, 850 nm, 1310 nm, and 1550 nm, pulse widths as low as < 0.3 ps, and GHz low-jitter synchronization signals, these systems provide ideal optical sources for high speed transceiver conformance testing and photodiode characterization.
-
Product
Transceiver Driver
S-112
-
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
Product
OSFP 800G
-
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
Product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
-
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
Product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785588-01
FlexRIO IF Transceiver
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785589-02
FlexRIO IF Transceiver
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Prototyping & Test Consulting Services Solutions
test
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
Product
Automotive Test Solutions
test
The testing and simulation systems from this division are used primarily in the automotive and automotive supplier industry. These are, for example, modular function-testing systems and diagnostic tools for automotive ECUs or bus communication systems for a wide variety of electronic components in automotive production. Electromechanical assemblies and entire car seats are also tested to ensure they function
-
Product
Gigabit Ethernet SFP Module
SFP-GSS-20KTX
Optical Transceiver
Hardened SFP/1250-ED, SSLX-SM/SC (1310XMT/1550RCV) 20km (also known as 808-38221) Industrial standard small form-factor pluggable (SFP) package, Provides digital diagnostics monitoring (DDM) functionality. Wide specifications and fiber types available, Comes with metal enclosure for EMI.
-
Product
LIN Transceiver Cable
783702-03
Transceiver Cable
The TRC-8546 is designed to provide flexibility in connecting a LIN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8546 to the port to support a LIN interface. The TRC-8546 is an isolated cable that includes the necessary transceiver for the bus type.
-
Product
Arbitrary Waveform Transceivers
Proteus Series
Waveform Transceivers
Tabor’s Proteus Arbitrary Waveform Transceiver enables you to transmit, receive and perform digital signal processing all in a single instrument. The Proteus AWT is a valuable tool for R&D labs in growing markets such as quantum physics, medicine, aerospace and defense, telecommunications and automotive. For synchronized, phase coherent, multi-channel applications such as quantum physics and radar applications the Proteus arbitrary waveform transceiver is an ideal, space efficient and cost effective solution.
-
Product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786856-01
Vector Signal Transceiver
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785585-01
FlexRIO IF Transceiver
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
BSD (Test Diagnostics)
test
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
LIN Transceiver Cable
783702-02
Transceiver Cable
The TRC-8546 is designed to provide flexibility in connecting a LIN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8546 to the port to support a LIN interface. The TRC-8546 is an isolated cable that includes the necessary transceiver for the bus type.
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
PXI Vector Transceivers
Vector Signal Transceiver
Get both signal generation and analysis in one PXIe module with real-time field-programmable gate array (FPGA)-accelerated measurements for faster throughput. The PXIe vector transceiver is perfect for manufacturing test of wireless devices, RF power amplifiers, and front-end modules.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.
-
Product
CAN HS/FD Transceiver Cable
783699-03
Transceiver Cable
The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
Product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786853-01
Vector Signal Transceiver
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
PXI FlexRIO IF Transceiver
FlexRIO IF Transceiver
The PXI FlexRIO IF Transceiver combines analog I/O and a user-programmable FPGA into a single, customizable instrument. The instrument enables direct RF acquisition up to 6 GHz. You can use the instrument in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXI FlexRIO IF Transceiver uses FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. Using this instrument with NI-TClk, you can synchronize modules in one or more PXI chassis at up to picosecond‐level accuracy for high‐channel‐count applications.
-
Product
PXIe-5830, 12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
787047-01
Vector Signal Transceiver
12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5830 supports validation and production test into mmWave frequency bands. This vector signal transceiver incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe-5830 helps you test a variety of cellular and wireless standards such as Wi-Fi 6. You can expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
EFT Module for Teststand
test
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
Product
NI Real-Time Test Cell Reference System
778820-35
test
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
VXT PXIe Vector Transceiver
M9421A
Vector Signal Transceiver
Purpose-built for rapid solution creation and faster throughput in manufacturing test of wireless components, power amplifiers, and RF front-end modules Increase test density and reduce your footprint with up to four VXT instruments in one 18-slot chassis Reduce development time with open-source test libraries and reference solutions Start closer to your finish line with built-in FPGA-accelerated measurements Optimize test routines using proven software for noise figure and standard-specific measurements
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
