Electromagnetic Interference
unintentional signal interference as a byproduct of normal operation, originating from within the system or circuit. Also known as: EMI
-
-
Product
ITA, 9050, 50 Module, Double Tier, EMI, with 8" Enclosure
410104580
ITA
This 9050 ITA comes with an 8" enclosure for ease of system integration. The ITA is designed to work with the 9050 EMI receiver.
-
Product
HDBaseT Transformers
-
Pulse HDBaseT transformers are designed to provide common mode noise reduction for improved EMI performance and support power over HDBaseT (PoH) applications of up to 100W. The HDBaseT technology enables 5Play feature set, which includes ultra high definition 4K video, audio, 100BASE-TX Ethernet, various control signals, and up to 100W of power, on a single 100m/328ft CAT5e/6 cable.
-
Product
EMC- EMI test Equipments
-
Our AFJ FFT 3100 & 3300 EMI Receivers cover the full frequency range from 9kHz to 3GHz.To allow a greater flexibility GTemCell can provide either a single or multiple solution of receivers to cover the most common standards and regulations such as CISPR, EN, IEC, FCC etc.
-
Product
DC Power Supply
PW-3032R
-
*Toroidal Transformer*Low EMI & High EMS*Very Low Ripple & Noise*30V/3A+5V/3A Dual output.*<0.3m Vrms Ripple & Noise(C.V.)*<2m Arms Ripple & Noise(C.C.)*Low EMI & High EMS.*Dual Display.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
EMI Test Receivers
-
EMI test receivers; extremely accurate instruments designed to detect electromagnetic emissions rigorously, to ensure all emissions conform to the Standard being tested to. Configured to set up running the required tests for parameters defined by the Standards as simply as possible, including automated test routines. R&S EMI test receivers can be much more too, with a full signal and spectrum analyzer in the same instrument.
-
Product
Handheld Power & Energy Meter
Nova 7Z01500
-
*Compatible with all standard Ophir Thermopile, Pyroelectric & Photodiode sensors.*Single shot energy measurement with thermal sensors.*Optional RS232 computer interface. Works with Ophir's StarCom32 application.*Power and energy logging with graphical display and statistics.*Laser Power Measurement averaging.*Easy to use soft keys, menu driven.*Screen graphics.*Backlight & rechargeable battery.*Analog output.*EMI rejection.*LabVIEW software included.
-
Product
RF Architectural Shielding Products
-
EMI (Electromagnetic Interference) is often used interchangeably with RFI (Radio Frequency Interference). However, EMI can be any frequency of electromagnetic noise, whereas RFI is a relatively narrow range of electromagnetic noise on the EM spectrum. EMI Shielding can be used to mitigate electric and magnetic radiation across various spaces. Radio Frequency (RF) Shielding can be used to mitigate RFI with specifically designed enclosures that can block RFI. As well, RF Shielding can include application of RF Shielding paints, fabrics, and other materials.
-
Product
ITA, i2 MX, EMI Backshell, with Cable Exit (Shell only, does not include front protective cover or modules)
410130114
ITA
ITA, i2 MX, EMI Backshell, with Cable Exit (Shell only, does not include front protective cover or modules)
-
Product
DC Power Supply
◎PW-4063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
RF Shielded Box
LTL B5001
-
LTL B5001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B5001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
Chassis
-
Infrastructure housing for instrument cards typically containing a power supply, cooling fans and emi shielding.
-
Product
EMF Measurements/EM Measurements/Electromagnetic Radiation
-
Holland Shielding Systems B.V.
Electromagnetic fields cause interference in electronic devices and may affect the health of people close to where the fields are generated. It is important to recognize this at an early stage in a construction process, for instance at a future construction location or while construction is already underway, so that budgets are not exceeded. By means of field-strength measurements one can chart the existing electromagnetic fields and radiation emitted by GSM, UMTS antennas and transformer spaces, to mention a few examples. These measurements can help determine the best location in the new building for rooms where sensitive measurements are to take place, e.g. in hospitals or nano laboratories. And last but not least, field-strength measurements can detect sources of interference and can be part of a scheduled check of existing screened spaces and Faraday cages.
-
Product
EMI Test System
EMI-9KA
-
EMI-9KA is an automatic EMI receiver. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KA is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KA fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
Product
Optically Isolated Measurement System
IsoVu
-
IsoVu offers complete galvanic isolation and is the industry’s first measurement solution capable of accurately resolving high bandwidth, low voltage differential signals in the presence of large common mode voltages. The stand out feature of IsoVu™ is its best in class common mode rejection across the entire bandwidth. Accurate differential measurements rely on a measurement system’s bandwidth, rise time, common mode voltage, common mode rejection capability, and the ability to connect to smaller test points to characterize devices that are shrinking in size and increasing in performance. Despite these requirements, advancements in test and measurement for power testing, EMI testing, ESD testing, and remote measurement capability have been minimal at best and have not kept pace with changing requirements. While differential voltage probes have had modest performance gains in regard to bandwidth, these probes have failed to make any substantial improvements in regard to common mode rejection, and connectivity. IsoVu is a leap forward in technology and is the only solution with the required combination of high bandwidth, high common mode voltage, and high common mode rejection to enable these differential measurements.
-
Product
CATV Measurement Receiver
VAROS 107
-
The VAROS 107 was specially designed for installation and maintenance of cable TV networks. The large high resolution TFT display, the backlit keyboard, the built-in DOCSIS 3.0 and EMI measurement all contribute to making work for the technician easier.
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Mission Processor
58U91-03
-
- +28 VDC input- 9 DC outputs at 600 Watts- Provides system EMI per MIL-STD-461- Continuous Background Built-In-Test (BIT)- Temperature monitoring- I2C communication
-
Product
Voltage Probes
-
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-4
-
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz*14-bit resolution*Output voltage: 0-10 V, ±10 V, (set through software)*Each output has its own ground line*Driver capacity: 5 mA/500 pF*Short-circuit protection: EMI filters*Data exchange through 16-bit I/O digital*4 digital inputs*and 4 digital outputs, 24 V , opto-isolated
-
Product
Chip Inductors-Multilayer
-
Bourns Miltilayer chip inductors offer high frequency, nickel barrier, monolithic construction for high reliability, and magnetically shielded construction providing low radiation. They are well-suited for DC-DC converters, and prevention of electromagnetic interference to signals on the secondary side of electronic equipment, among many applications.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
Antenna, Active Loop
EM-6876 | 9 KHz – 30 MHz
-
The Electro-Metrics EM-6876 Active Loop Antenna is used with EMI Receivers and Spectrum Analyzers with 50 ohm input and covers the frequency range of 9 kHz to 30 MHz.
-
Product
EMI Receiver
KH3935
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3935 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3935 receiver is from 9kHz to 30MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be performed. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing.
-
Product
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)
510181111
SIM Insert
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 410130116, ITA, i2 MX, 22 Slot VTAC/SIM Insert, EMI, and XL version 410130133Not loaded. Thermocouple patchcords need to be purchased separately.
-
Product
EMI Receiver
KH3939
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
Product
ITA, 9075, 75 Module, Triple Tier, for EMI
410104449
ITA
ITA, 9075, 75 Module, Triple Tier, for EMI
-
Product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers, EMI Gasket
310104429
Receiver
The 9050, 50-module receiver is rugged and designed to accommodate high I/O and suited for larger test and measurement systems. Both tiers are designed for discrete wiring and can accommodate individual 9025 ITAs. This 9050 also offers a gasket for EMI applications.
-
Product
Bench Power Supplies
Series ABC
-
Kepco¹s ABC bench power supply embodies the latest features: keyboard data entry, interactive digital display, integral GPIB support, software calibration, high frequency switch mode conversion, wide range input (85-264V a-c) and power factor correction. It meets the EN 61000-3-2 harmonic limits. A built-in EN 55022 Class B input EMI filter is provided. Integral External Trigger and RS 232 ports are now standard features.
