-
product
Inmarsat-C Physical Layer Tester
CPLT
Square Peg Communications Inc.
Square Peg Communications Inc.’s Inmarsat-C Physical Layer Tester (CPLT) is a software application that runs on the generic high-rate Physical Layer Tester (PLTH) platform. The CPLT supports testing of the physical layer performance and protocol implementations of Inmarsat-C Mobile Earth Stations (MESs) and Land Earth Stations (LESs).
-
product
IEC60335-2-9 Clause 3 Figure 103 Vessel For Testing Hotplates
CX-GZ
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 103 Vessel for testing hotplatesParameter:1.Pot and lid material industrial aluminum2. Pot material thickness 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm;4. Pot body and lid surface should be smooth;5, size: 110, 145, 180, 220, 300mm each one
-
product
Regenerative Grid Simulators
Chroma Systems Solutions, Inc.
Rigorous testing to industry regulatons and standards for the safe operation of on-grid products.
-
product
Multi-site Module Testing System
TCIII-3200ST
TurboCATS introduces a new line of redesigned TCIII-3200ST DDR4 and DDR3 multi-site module testing system - compact, high-performance, and equiped with enhanced productivity features. The TurboCATS TCIII-3200ST module test system features an optional 8, 16 or 64 module testing, in parallel, for high throughput on your production floor.
-
product
Three-phase Fully Automatic Test System
TS41
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
product
EMI Testing
Independent Testing Laboratories
ITL offers compliance and qualification testing for virtually any type of electronic product or system.
-
product
Impulse Hammers/Impedance Heads
Impulse hammer excite from the smallest of structures to various civil engineering structures. The Dytran model 5800SL is an ultra miniature IEPE impulse hammer used to excite structures or machinery with a definable impulse force in modal and structural analysis of very light structures and impulse testing of very low mass, high resonant frequency components.
-
product
Smart Data Testing Solution
• Improve your data quality at speed• Dramatically increase data coverage• Detect data issues early in the delivery cycle• Leverage analytics to optimize your critical data
-
product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX3032T
350 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
Highly Accelerated Stress Test Chambers
HAST
Our HAST systems have a modern design that's easier to use: Automatic humidity filling; Automatic door lock; A more square workspace; allowing more product to be loaded;Convenient, hermetic power-pin system for bias testing. We are now able to offer a hermetic port system to allow special signal lines like coax or fiberoptics to be run into the chamber.
-
product
Infiniium V-Series Oscilloscope: 25 GHz, 4 Analog Channels
DSOV254A
25 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Industrial Cabinet Oven
Gruenberg designs and manufactures a complete line of standard and custom industrial cabinet ovens, sometimes called reach-in ovens, to accommodate a variety of thermal processing applications up to 1200°F, which are ideally suited for annealing, aging, core hardening, drying, preheating, curing, and component testing. With additional options, they can also be used for applications such as epoxy, plastic, and rubber curing; paint and varnish baking; textile drying; and sterilizing.
-
product
Current Generator
MIG12100
MIG12100 is a current generator with wave shape 8/20 ìs. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied. The generator can deliver up to 100kA impulse current supported by 12kV impulse voltage, making it ideal for testing big varistors with high hold-on voltage. Mechanically the MIG12100 consists of two large racks and a separate control console with high voltage output terminals protected by a glass acrylic test cabinet.
-
product
Power Analyzer
CWDM Power Analyzer provide very high productivity for power testing of high density fiber optic systems and devices for E-PON and CWDM PON system or local network system. CWDM Power Analyzer can be tested at up to 18 wavelengths in one operation, providing major operational savings. The real time display update in this mode is unique, and typically offers genuine time saving for users.
-
product
Product Safety Compliance Testing
We can accommodate any project scope. Whether you have the need for NRTL certification, European Low Voltage Directive (LVD) compliance, or to satisfy internal production control requirements, our Product Safety testing services can meet your needs.
-
product
Torque Testing
Torque testers measure properties such as torsional strength and stiffness and are used in quality control of various fields including medical devices, metals, and aerospace
-
product
Taber Type Linear Abraser
SG-P01TL
The tester is used for test either contoured or flat surfaces, making it ideal to evaluate finished products of all sizes. It can be used for both wet and dry testing.
-
product
Axle Damping Test Bench
C_MSD S 2.5 W220 | VP 215048
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
Torque Carts
AIMCO offers torque carts for "lineside" or "point of use" tool validation and calibration. Our torque carts allow testing of tools on repeatable joint simulators and "in process" use on production joints, allowing users to identify process capability. There are multiple torque cart options:
-
product
Relay Buddy Adapter Set
190-4
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
product
Accelerated Aging
The purpose of accelerated aging testing is to speed up the effects of time on a product. This is done to predict the long-term durability and to support shelf-life and expiration dating claims. This is often used in the medical device packaging industry. The relationship between temperature and product life is utilized to determine the test duration of accelerated aging.
-
product
RF and Vector Signal Analysis Software
SignalVu-PC
SignalVu-PC is the foundation of RF and vector signal analysis software that helps you easily validate RF designs. Whether your design validation needs include EMI/EMC pre-compliance testing, wideband radar, wireless LAN or frequency-hopping communications, the SignalVu-PC comprehensive suite of tools and application software can speed your time-to-insight by showing you the time-variant behavior of these signals.
-
product
Space Flight Components
A tec, Inc. specializes in the design, manufacture, and integration of complex test systems and quality critical components. Our production engineering expertise separates us from other manufacturing companies when both reliability and cost are important. Atec has the best in 5 to 9 Axis CNC machining, coordinate measuring machines (CMMs), 3D additive metal and plastic printers, 9-Axis capable waterjet, cryogenic liquid flow test benches and environmental test chambers. We can deliver to the tig...show more -
product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety sta...show more -
product
MPO/MTP MANDREL FREE IL/RL LOSS TEST STATION
Shanghai Fibretool Technology Co.,Ltd.
FBT-M24 mandrel free insertion loss test station is specially design for multi fiber testing. It realized mandrel free return loss measurement on the multi fiber, and without matching gel for the MM measurement. This test station also do the auto-testing on 12 core (24 core) for insertion loss and return loss, highly efficient multi-core fiber insertion and return loss measurement and make high precision on the measurement result with OTDR mandrel free technical adopting.
-
product
Engine Test Systems
Dynas3
Dynas3 Machines are specially suited for use in engine test stands. The AC machine, variable frequency drive with test stand controller and safety module are tuned to one another to form a system that has proven itself many times over. It can be used in any type of development and function test stand. The applications range from simple test stands for steady state operation up to sophisticated test stands for dynamic test cycles. Nearly every application in the field of engine testing can be performed on a test stand with DYNAS3.
-
product
Pulse & Delay Generators
Berkeley Nucleonics Corporation
Provides high frequency pulses, delays and bursts. It is an ideal testing and timing control instrument for electronics, lasers or camera setup.
-
product
Charged Plate Monitor
Model 157
Trek's Model 157 Charged-Plate Monitor offers greater accuracy, stability and bandwidth than conventional designs. This model combines Trek's patented precision charge measurement capability with features that drive down the cost of ionizer performance testing and maintenance. Model 157 is suitable for semiconductor, disk drive, LCD and many other manufacturing environments that are sensitive to static charge.
-
product
PXI 3A Power MUX BRIC, 8-Channel, 6-Pole
40-571-401
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Current Generator
MIG1260
MIG1260 is a current generator with wave shape 8/20 μs. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied. The generator can deliver up to 60kA impulse current supported by 12kV impulse voltage, making it ideal for testing big varistors with high hold-on voltage. Mechanically the MIG1260 consists of one large rack and a separate control console with high voltage output terminals protected by a glass acrylic test cabinet.