Fuel Cell Stack
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Cell Production Measuring Technology
-
More than 2000 halm systems are already installed in the field, all of which fully comply with the IEC60904-9 standard. In the latest standard (Edition 3.0), our current systems are even rated A+A+A+.
-
Product
Wireless Load Cells and Electronics
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Force Load Cells
-
TE Connectivity (TE) offers load cell assemblies for test and measurement applications that require high performance or unique packaging. Our broad range of packaged load cells feature foil strain gages enabling OEM's to measure force with low cost and high reliability. The gages produce a high level of output signal for a low operating stain using inorganic materials to offer long term stability. Load cells are gaged in a variety of materials from high strength stainless steel to special alloys.
-
Product
Load Cell Amplifier
-
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
Product
Laboratory Liquid Two-Electrode Battery Test Cell
LLB1
-
A reusable laboratory coin cell simulator designed for battery research, electrochemical experiments, and material evaluation with reliable sealing and repeatable testing performance.
-
Product
Cell Testing
-
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
Product
Fuel Injector Tester GM Multiport
FIT457
-
For GM domestic cars with large schrader adapters; light trucks, vans and sport utility vehicles with multi-port. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Basic Fuel Injection Pressure Tester
FIT448
-
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
Product
NI Real-Time Test Cell Reference System
780590-35
test
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Heavy Duty Shear Beam Load Cells
SBL SERIES
-
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
Product
Through Hole/ Donut Load Cell Compression Only
THA SERIES
-
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Solar Cell I-V Characterization System
VS6825
-
Industrial Vision Technology Pte Ltd.
The VS-6825A I-V test system is tailored for high-efficiency Solar cell production lines. It is able to eliminate the impact of HJT/IBC/TOPCON’s high capacitance characteristics on measurement results.
-
Product
Test Cell Vibration Monitoring System
-
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
Product
Voltammetry Cell
VC-4
-
Capable for measuring of 1 - 3 ml of sample volume using electrodes with 6 mm of the diameter. Furnished holder prevents the vial from spilling.
-
Product
Fuel Injection Pressure Tester w/2 Gages & Quick Couplers
53950
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
Product
PXI Mixed Configuration Relay Module - 6 Cells Populated
40-138-AA-BB-CC-DD (6 CELL)
Relay
The 40-138 2A Relay Module with 6 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Battery Cell Tester
-
This Centre zero instruments help to read the voltage irrespective of polarity.
-
Product
Load Cells
-
Applied Weighing International Limited
Range of tension load cells are suitable for smaller Silo, vessel and tank weighing applications. The load cell can be supplied as a fully welded stainless steel or tool steel. Capacities from 1000kg to 5000kg Fitting options available including threaded bar, rod end bearing and eyebolts. ATEX option available.
-
Product
PXI Mixed Configuration Relay Module - 8 Cells Populated
40-138-AA-BB-CC-DD (8 CELL)
Relay
The 40-138 2A Relay Module with 8 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Graphite CBrass Flow Battery Electrochemical Cell
GSF1
-
A laboratory square flow battery experimental kit designed for electrolyte circulation studies, redox flow battery research, and electrochemical testing with stable liquid flow and corrosion-resistant construction.
-
Product
SolarIV Series Solar Cell Current Voltage Measurement System
SlarIV
-
SolarIV IntroductionOne of the key measurements needed for photovoltaic devices in the measurement of their I-V characteristics. Through measuring the I-V curves the user can determine physical performances of devices such as photo-electric conversion efficiency, fill factors and so on. Such data is important for reliable work in research and quality inspection. ZOLIX supply the SolarIV system and the most perfect, professional technical support.
-
Product
8-Channel VME Strain Gauge/Load Cell Module
V385
-
The V385 is a VME/VXI compatible eight-channel strain-gauge signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the V380's single excitation supply.
-
-
Product
Load Cells
-
Whether you're selecting a replacement load cell or a specialized load cell for a custom application, Rice Lake can get it to you right away. Our knowledgeable customer service representatives are on hand to answer questions and help you select the best equipment for your needs.
-
Product
Low Profile Compression Only Load Column Load Cell with Mounting
CLC SERIES
-
Our CLC Series is our high capacity compression only load cell, featuring low profile compact size for a wide range of portable and dedicated applications. The loading diameter (D1) is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. All ranges are made from 17-4ph heat treated stainless steel and incorporate a stainless steel molded connector system designed to resist washdown and splash. The mating connector, sold separately, is available in three different cable lengths.
-
Product
Flow Cell Kit
QCMT
-
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
