Solderability
-
Product
GPIB to Relay Minibox™
Model 4864
-
* Model 4864-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Optional terminal board and terminal strip for easy connections without soldering. See the GPIB Accessory page. * Model 4864-12 provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as listed for the 4864-11. * Model 4864-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as listed for the 4864-11.
-
Product
CyberOptics SE Series
SE Series
-
The CyberOptics SE Series offers the most accurate and repeatable, high speed 3D solder paste inspection in the market today. Utilizing the most advanced sensing technology, CyberOptics SPI products will provide manufacturers the reliability needed to compliment your overall screen print process improvement strategy.
-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Solder Cup Connector Kit
Y1139A
-
Used to build custom cables for 34921/23/25/31/32/33/37/38 –50-pin Dsub female – 125 V
-
Product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
-
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
Product
75 Ohm TNC Connectors
-
Pasternack 75 Ohm TNC connector category has several part numbers, most of which are RoHS and REACH compliant. 75 Ohm TNC connector series in this category will terminate to coax or terminal. Our 75 Ohm TNC connectors are built to precise microwave and RF industry specifications. TNC 75 Ohm connector products are available in male or female gender with 75 Ohm impedance. 75 Ohm TNC connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm TNC connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm TNC connector series is in-stock. Not just in stock, these TNC connectors in 75 Ohm impedance will also ship the same day as they are purchased.
-
Product
Fusion Bonded Cable Jumpers
Series 152FB
-
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
Product
Garmin LIDAR-Lite V4 LED
Distance Measurement Sensor (Qwiic)
-
The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic system really shines. The LIDAR sensor requires 5V to operate but runs on 3V3 logic. With a 5V boost circuit and an easy-to-use Qwiic connector you can power the sensor and get distance measurements over Qwiic all with a single piece of hardware.
-
Product
LEDs
-
Several applications need an optical indication to show a specific situation. Our LED array assortment covers the most demanding requirements on a cost-effective way. The robust and standardized design can be soldered easy and save to any standard PCB. From THT LED devices to innovative IP68 sealed light guides, Elma can provide a quick off-the-shelf solution or customize a product to fit your needs.
-
Product
SparkFun Cryptographic Co-Processor Breakout
ATECC508A (Qwiic)
-
The SparkFun ATECC508A Cryptographic Co-Processor Breakout allows you to easily add strong authentication security to your IoT node, edge device, or embedded system. It includes two Qwiic ports for plug and play functionality. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard. The ATECC508A chip is capable of many cryptographic processes, including, but not limited to:
-
Product
SCANNER BASED IN-LINE & DESKTOP AOI
SS15000-PAL & SS15000-IL
-
AOI Systems ScanSpection uses two basic algorithm groups to inspect component and soldering. The first algorithm checks the component related parameters at once, with these being entered to a Model training phase. The second algorithm group is for solder and lead inspection and offers the ability to use the optimum algorithm for the type of inspection to be carried out. In addition the solder inspection and lead inspection can be attached to a package type rather than component type to assist in programming.
-
Product
QMA Connectors
-
Pasternack QMA connector category contains dozens of part numbers, most of which are RoHS and REACH compliant. QMA connector series in this category will terminate to coax or PCB (printed circuit board). Our QMA connectors are built to precise microwave and RF industry specifications. QMA connector products are manufactured in male or female gender with 50 Ohm impedance. Connectors in the QMA category are available in straight or right angle versions, as well as, bulkhead or mountless options. These QMA connector designs include crimp/solder, solder or solder/solder attachment methods. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this QMA connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
-
Product
BNC Twinax Connectors
-
BNC Twinax connector category has several part numbers, the majority are RoHS and REACH compliant. BNC Twinax connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC Twinax connectors are built to precise industry specifications. Pasternack BNC twinax connector items are available in jack or plug gender with 78 Ohm impedance. Connectors in twinaxial BNC are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These BNC Twinaxial connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this twinax BNC connector series is in-stock. In addition to being in stock, these twinaxial BNC connectors will ship the same day as they are purchased.
-
Product
68-Pin Micro-D Male Solder Bucket With Backshell
40-962B-068-SB-M
SCSI Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
4-Pin Power D-Type Female Connector, 40A, With Backshell
40-960-004-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
Product
SMB Connectors
-
Pasternack SMB connector category has dozens of part numbers, most are RoHS and REACH compliant. SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB connectors are built to precise microwave and RF industry specifications. Connectors in the SMB series are manufactured in jack or plug gender with 50 Ohm impedance. SMB connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this SMB connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
-
Product
Ultrasonic Cleaner
Stencil Washer
-
Harnessing the Safe Power of Sound-Waves, StencilWasher Removes all Solder Paste and SMT Adhesive Types in Zero or Low Discharge Configurations
-
Product
9 Pin D-Type Connector, Male
92-960-009-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cleaner for Test Probe
EQOmat
-
We have developed EQOmat, a cleaner exclusively for test probes that removes dust such as flux and solder debris adhering to the tip of the test probe. The structure and thinness built with the user's convenience in mind are important items that have sufficient functionality and are indispensable for long-term use of the probe. * EQOmat is an abbreviation for Ecological Qualified Octopus Mat.
-
Product
15-Pin D-Type Connector, Male
92-960-015-M
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
BNC Connectors
-
Pasternack BNC connector category includes many part numbers, most are RoHS and REACH compliant. BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC connectors are built to precise industry specifications. BNC connector items are constructed in male or female gender in standard polarity or reverse polarity threads, with 50 Ohm impedance. Connectors in BNC series are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These BNC connector designs include clamp/solder, crimp/solder, field replaceable, solder or solder/solder attachment methods. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this BNC connector series is in-stock. Not only in stock, but these BNC connectors will ship the same-day as they are purchased.
-
Product
Universal ZIF (Zero-Insertion-Force) DIP Test Socket
Series X55X
-
Universal Zero Insertion Force DIP Test Socket. All pin count sockets go into PCB with either .300 or .600 [7.62 to 15.24] centers. Sockets can be soldered into PCBs or plugged into any socket. Socket fits into Aries or any competitive test socket receptacle.
-
Product
BGA SMT Adapters
Giga-snaP™
-
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
Product
Hot Air Rework Station
21-10125
-
The 21-10125 is a hot air Rework Station provides a wide range of temperature and temperature settings for flexibility in soldering and desoldering work of sensitive components. A closed-loop heat sensor provides accurate and consistent working temperature. It features an intelligent cooling system cools the hand-piece with continued air movement after power has been switched OFF.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Eurocard Plugbord
E160-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides.Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
Solder Joint Inspection System
-
DMC developed the software to inspect the solder joints of automotive power door lock switches.
-
Product
Odd Shape Assembly Cell
JOT
-
The reusability of the platform and feeders is close to 80%, allowing the platform to grow and adapt with future business needs. The same cell is easily expandable to automate over 20 different processes and configurable to versatile applications like screw insertion, soldering, laser marking, labeling and packaging.
-
Product
Circbord
8021
-
VECTOR Electronics and Technology, Inc.
Copper plated-thru holes with solder plating, peripheral ground plane.3U X 160mm Eurocard size will fit into 3U DIN Metric subrack..
-
Product
Eurocard Plugbord
E220-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
