Solderability
-
product
Nanotek Brush
Nanotek Series
Nanotek Brush is fine stainless wire brush for removing solders or dirt stuck on the tip of spring probe. It has its range of wire diameter from 30µ to 50µ and its fine wire is effective for removing solder or dirt on complicated tip type. We also have Nanotek vacuum, which is nanotech brush combined with vacuum cleaner powered by your compressor or vacuum pump.
-
product
Circbord
106P180-4
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole & Overall Ground Plane both sides.Individual pads with plated-thru holes. 0.080” diameter isolated solder pad around each hole on both sides. Etched ground plane surrounds pads on both sides
-
product
SparkFun Qwiic Thermocouple Amplifier
MCP9600 (Screw Terminals)
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
product
Lock/Eject DIP Collet Socket with Surface Mount Pins
EJECT-A-DIP
Lock/Eject DIP Collet Sockets with Surface Mount Pins. Features: Aries Eject-A-Dip is a rugged, solderable socket with a unique ejector/latch for fast in-field board maintenance. The latch locks in the connector or device, making it ideal for high vibration environments. The latch, when used as an ejector, removes DIP packages without pin damage.
-
product
DDR4 MSO Probes
The DDR4 DIIM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR4 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR4 signals for convenient analog probing. The user can then easily observe both the digital and analog representation of the DDR4 Address, Command and Control bus. Solder down N5541A analog probes purchased separately from Keysight Technologies.
-
product
Hard Metric Eurocard Plugbord
8024
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. 3-Hole solder pads both sides. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
40-960-104-M
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell.
-
product
8 Pin Power D-Type Male Connector, 40A, Without Backshell
92-960-008-M
This connector is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
product
68-Pin SCSI Micro-D Female Solder Bucket
40-962-068-SB-F
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
9-Pin D-Type Connector, Female
40-960-009-F
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
Wave Soldering Machines
Shenzhen Leadsmt Technology Co.,Ltd
A bulk soldering process used for the manufacturing of printed circuit boards.
-
product
K-Type Temperature Probe
TP475
K-Type Temperature Probe for Calibration of Soldering Stations with Hollow Heaters
-
product
Solder Test Pallet
WaveRIDER® NL 2
The wave soldering process is one of the most challenging procedures to set up. The ECD WaveRIDER NL 2 greatly simplifies wave solder set up and ensures perfect repeatability, time after time. Board recipe preheat temperatures, conveyor speed, wave height, contact times and parallelism are all measured and monitored using the WaveRIDER NL 2 process pallet.
-
product
Ethernet Digital Interface OEM Board
8063
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
product
44-Pin D-Type Connector, Male
40-960-044-M
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
QFP-to-PGA Motorola 68340 144-Pin Adaptor
97-68340
144 Pin QFP to PGA Adapter for Motorola 68340. Convert surface mount QFP packages to a 15 x 15 PGA footprint. Reduce costs by using less expensive QFP packages to replace PGA footprints in existing designs. Pins are mechanically fastened and soldered to board using Aries patented process, creating a reliable electrical connection and rugged contact.
-
product
50-Pin D-Type Male with Backshell, HV
40-960-050-M-HV
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
26-Pin D-Type Connector, Male
40-960-026-M
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
Low Resistance Meter
MMR-640
The MMR-640 meter is designed to measure very low resistance of resistive objects. This product is made to be used in power plants, railways and maintenance companies to measure resistance of:*breakers, contacts,*earthing conductors, equipotential bondings,*welded and soldered connections,*bolted connections,*and other resistive objects.
-
product
MyoWare 2.0 Muscle Sensor
Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks... but what if we could take the buttons, levers and joysticks out of the equation and control it with our muscles? The MyoWare® 2.0 Muscle Sensor is an Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies that allows you to do just that! The MyoWare 2.0 Muscle Sensor has been redesigned from the ground up with a new easy-to-use, compact design and upgraded with the latest and greatest chipset improving sensor performance and reliability. The innovative snap connector system eliminates the need to solder connections for the MyoWare 2.0 ecosystem. It's that easy: stick on a few electrodes (not included), read the output voltage and flex some muscles!
-
product
SparkFun Qwiic Single Relay
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!
-
product
3-Pin Power D-Type Connector, 40A, Female Without Backshell
92-960-003-F
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a direct termination with soldered connections.
-
product
Plugbord
3677
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers. 3-Hole solder pads (0.28” x 0.080”) and buses forinterconnecting multiple component leads. No pattern on reverse side, edge contacts only Row and column legends provided.
-
product
6U Compact PCI® Single Board Computer
CP62001
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
product
Plugbord
3682
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience. Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
product
Breadboard to DAQ Converters
0001026-1 / -2
VI Control Systems has designed two converter boards that make it easy to connect data acquisition boards to breadboards and allow easy computer control and monitoring of prototyped electronic circuits. The converter boards are 0.8 x 3.5 inches and have silk-screened pin numbers for every pin on the board. The 68-pin SCSI converter can also be used to connect 68-pin SCSI cables to prototype solder boards that have 0.1 inch centers.
-
product
Full 3D Inline Metrological & Imaging AOI
Metrological Full 3D AOI is achieved by measuring all 3 dimensions (X, Y and Height) to detect every measurable solder and component defect pre-reflow and/or post reflow soldering.
-
product
Circuit Card Assembly
Teledyne Advanced Electronic Solutions assembles and tests a variety of complex circuit card assemblies (CCAs) using leading edge, advanced technology assembly automation. We specialize in low-volume, high-mix assembly of highly complex CCAs.- RF, analog, high-speed and digital circuits on rigid-flex and Cu core substrates- Typical lot sizes from 3 to 300 pieces- 4 high speed, flexible SMT lines- Production processes for components from 0201 chips to large grid-array components and connectors- 100% solder paste, automated optical, and x-ray inspection- Forced air convection reflow with inert atmosphere option- Special processes for RF assemblies (filters, shields, etc)- BGA underfill, conformal coating, etc.- Selective and wave solder pin-thru-hole processes- CCA and component bonding processes
-
product
68-Pin VHDCI Connector, Slimline - Male, Solder
C068VMR-6SB-6A
This slimline version of the VHDCI connector is designed to allow users to directly terminate a cable with soldered connections to the 68 Way VHDCI connector. It is difficult to terminate cable to the 68 pin VHDCI because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
Ultimus I-II Dispensers
High-precision benchtop fluid dispensing control for advanced applications of glues, oils, greases, epoxy, silicones, sealants, cyanoacrylates, solder pastes, and other assembly fluids dispensed with syringe barrels.
