Prototyping Boards
-
Product
BMP-1-S Board Marker Probe
BMP-1-S
ICT/FCT Probe
Current Rating (Amps): .05Voltage Rating (VDC): 15Recommended Duty Cycle: 1 sec. On (min.), 5 sec. OffTest Center (mil): 1,000Test Center (mm): 25.40Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Rec. Mounting Hole Size (mil): 468Rec. Mounting Hole Size (mm): 11.89Recommended Drill Size: 15/32 (in) or 11.90 mm
-
Product
3U CPCI I/O & Comm Board
3U cPCI 75C5
Multifunction I/O
NAI’s 75C5 is a 3U cPCI Multifunction I/O and Communication Board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed Analog-to-Digital (A/D) channels and 28 Discrete I/O programmable channels, or with a reference power supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
3U OpenVPX Multichannel Discrete I/O Board
68DT1
Multifunction I/O
The 68DT1 is a 3U OpenVPX™ board featuring up to 96-Channels of Standard Functionality (SF) DT1 module-type or Enhanced Functionality (EF) DT4 module-type Discrete I/O functions [foptioned, factory configurable].48-Channels are dedicated as input (voltage or contact sensing with programmable, pull-up/pull-down current sources). An additional 24 or 48-Channels are programmable for either input or output (current source, sink, or push-pull) switching up to 500 mA per channel from an applied 3 – 60 V external VCC source (or sink to ISO-GND). The 68DT1 can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 EF are listed below. The 68DT1 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for pull-up resistors or mechanical jumpers.
-
Product
SparkFun MicroMod Machine Learning Carrier Board
-
The MicroMod Machine Learning Carrier Board combines some of the features of our SparkFun Edge Board and SparkFun Artemis boards, but allows you the freedom to explore with any processor in the MicroMod lineup without the need for a central computer or web connection. Voice recognition, always-on voice commands, gesture, or image recognition are possible with TensorFlow applications. The cloud is impressively powerful but all-the-time connection requires power and connectivity that may not be available. Edge computing handles discrete tasks such as determining if someone said "yes" and responds accordingly. The audio analysis is done on the MicroMod combination rather than on the web. This dramatically reduces costs and complexity while limiting potential data privacy leaks.
-
Product
Breakout Boards
-
Breakout your Raspberry Pis and Arduinos with this broad selection of versatile breakout boards! Engineered to help you realize your robotics, GPS and altitude sensing projects as well as servo and touch screen interfacing, you''ll find many uses for these high-quality boards, most of which are manufactured in house at Adafruit!
-
Product
Multiprotocol Serial Boards
104-COM-8SM-T
-
This is an eight-, four-, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports RS-232, RS-422 or RS-485 communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors. Common applications include POS, gaming systems, machine monitoring, military and high-density networking.Type 16780 UARTS are used as the asynchronous communication elements.
-
-
Product
Infotainment Platform & Boards
-
ADLINK offer ADi-SA1X/SA2X series, a true application-ready gaming platform, that is designed to meet the GLI-11 (Gaming Laboratories International) certification and major global gaming market compliance requirements. The comprehensive middleware as well as the security and extensive I/O solutions enable developers to easily bridge applications with peripheral devices, sensors, and surrounding solutions up to central monitoring and control systems that shorten customers TTM .
-
Product
Bi-Polar low voltage power supply board
LVPS
-
This is our standard power supply board used in many of our testers but also available separately. This board is capable of +/-15v, +10 and +5v outputs. Also contained on board is our standard meter drive circuitry for testing instrument meters, a two-pole relay and an option for a sine/cosine oscillator circuit.
-
Product
Express Multi Protocol Board
EXC-8000PCI
-
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
Product
Printed Circuit Board Inspection System
-
NIDEC-READ offers an array of testing equipment used to conduct open/leak tests on motherboards, as well as many other printed circuit boards. They can be flexibly configured according to applications in terms of size, type, and the number of test pins required.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
ISA Digital IO Board
MS 1804
-
*Discrete Input / Output 48 Channels*TTL Pulse measurement channels (Timers / Counters) 12 Channels*TTL Pulse Generation 12 Channels*Bi-directional Bus 16 Bit*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PCI Express A/d Board
AD14-500x4-8GB-K7US
-
The AD14-500x4-8GB-K7US is a high performance wideband 4-channel 14-bit data single PCIe Gen3 board, that can continuously digitize four wideband signals, with four high linearity A/Ds.Designed for demanding military, medical, scientific, industrial, communications, safety and electrical power utility applications, these boards have a wideband noise figure of 10dB and 1 dB peak-to-peak ripple over the DC to 250MHz frequency spectrum (2dB p-p over DC-500MHz).
-
Product
PCI Digital I/O Boards
PISO-P32A32U
-
The PISO-P32A32/P32A32-5V/P32A32U has 32 channels of optically isolated digital input and 32 channels of optically isolated digital output, arranged into four isolated banks. Each digital output offers a PNP transistor and integral suppression diode for the inductive load. Isolated input channels 0-15 are designed into group A, while channels 16-31 are group B. Isolated output channels are designed into group C and Group D. The photo-coupler input of the PISO-P32A32-5V can be powered by either an internal current source or an external power supply, while the input of the PISO-P32A32/P32A32U works with external power only.
-
Product
PCI Data Acquisition Boards
AD8-650X2DMA Series - 8 bit, 800MS/s
-
Model AD8-650X2DMA is similar to the AD8-1250DMA, but contains two simultaneous-sampling A/D channels, each capable of sampling at up to 800 MS/s.
-
Product
Fiber Optic Transmitter/Receiver & Repeater Board
-
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
Product
Single Board Computers
ITX-P-C444
-
The ITX-P-C444 is an industrial Pico-ITX single board computer (SBC) with NXP’s i.MX8M application processor and packed with dual Ethernet, industrial I/O, and expansion options. The processor supports industry-leading video processing along with an M4 microcontroller for real-time subsystems making it an ideal fit for industrial IoT applications requiring performance in harsh conditions such as digital signage, industrial automation, energy management, building automation, among others.
-
Product
Prototyping Adapters/Interposers
-
Prototyping adapters breakout from any package type to 2.54mm pitch pins or a larger pitch SMT footprint to solder to your development board. Our extensive design library means that many are available for fast delivery or next day from RS Components.
-
Product
PCI Daughter Boards
DB-8225/1/DIN (with DIN-Rail mounting kit)
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
PC/104 OneBank I/O Board
EMC²-KU40
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU40 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU40 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
VXI Register-based Interface Board
-
VXI Register Interface mates with user's PCB to form a B or C-size module.
-
Product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
Breakout Board
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Data Acquisition Processor Board
DAP 5000a
-
When your application needs Pentium-powered real-time processing under Windows, choose the DAP 5000a. Even at maximum sampling rates, the combination of a fast processor with low latency allows computation in real time between samples – and on-time response for control applications.
-
Product
PCI Analog Output Boards
PM-3114-100-CPS
-
4 Loops Single-phase Compact Smart Power Meter with 4 CTs (60 A), communicates over CANopen protocol. Supports Input types: Vrms, Irms, kW, kWh, kVA, kVAh, kVAR, kVARh, and PF. Supports operating temperatures between -10 ~ +70 °C (14F ~ 158F).
-
Product
PCI Analog Output Boards
PIO-DA16U
-
14-bit 16 Channel Analog Output Board auto detected by Windows. Includes CA-4002 D-Sub connector
-
Product
VME/VME64x Load Board
-
VECTOR Electronics and Technology, Inc.
The 6U VME and VME64x load board functions to test a system’s cooling capability by applying a variable load to the power supply for verification, then generating necessary heat to confirm the chassis’ cooling. This enables locating hot spots in the chassis so the airflow can be properly directed.
