Time Delay Relays
Time difference between two events. (thefreedictionary.com)
-
Product
Microwave Relays (SP3T to SP12T)
CXM/3x1 to CXM/12x1
-
CXM/3x1 to 12x1-NO-SMA Microwave Relays are Normally Open (NO) in the OFF state. Only one port can be on at a time. Larger configurations can be built by connecting the common port of multiple relays to another relay in series.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
Time Domain Reflectometers
HL1100 Series
-
HYPERLABS HL1100 Series TDR instruments provide high-performance test and measurement capabilities for use in the field or in the lab. These instruments are used for applications such as fault detection in cables and interconnects, impedance characterization, time of flight analysis, water level measurement, and more.
-
Product
Modular Real Time Video and Audio Processing
Synapse
-
Synapse is the industry’s most powerful and comprehensive audio and video processing system. Synapse modules make it possible to process, distribute, convert or analyse any type of uncompressed video and audio signal. Some examples: frame synchronization, video up & down conversion, audio (de)embedding, Dolby processing, integrity checking, logo insertion, multiviewing, etc.
-
Product
Time To Stop CO
-
Focuses on the dangers of Carbon Monoxide (CO) and the importance of detecting it using Kane analysers to prevent poisoning.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Remote Mount, Failsafe
42-780B-752-E
Relay
The 40-780B-752-E (PXI) and 42-780B-752-E (PXIe) are dual failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
4DI/4 Relay Output Modbus RTU Remote I/O
ND-6160
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
General Purpose PXI Relay Switch Modules
Switch Module
PXI relay switch modules offer reliable switching in a variety of configurations. They consist of multiple independent single-pole single-throw (SPST), single-pole double throw (SPDT), double-pole single-throw (DPST) and double-pole double-throw (DPDT) relays. Our PXI relay switch modules come in a variety of relay types including reed relays, electromechanical relays (EMR) and solid state relays—offering you the optimum switching performance for your application.
-
Product
USB-6525, 16-Channel, 60 V, 8 Solid-State Relays, 8 Inputs, Ch-to-Ch Isolated Digital I/O Device
779640-01
Digital I/O Module
The USB-6525 is an industrial, bus-powered USB I/O device that can automate even the most demanding applications. The solid-state relay outputs are ideal for controlling pumps, valves, motors, and various other industrial actuators. The USB-6525 features channel-to-channel isolated digital inputs that you can use to read from industrial digital sensors, and eight solid-state relay outputs featuring 60 VDC/30 Vrms switching voltage and 500 mA per channel maximum switching current. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators.
-
Product
Ultra High Density 4mm Reed Relays
122-1-A-5/2
Reed Relay
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A5 V Coil
-
Product
Real Time Spectrum Analyzers
RSA500 Series
-
Find signals of interest and take the necessary actions to resolve issues with industries best ruggedized, portable USB Real-time Spectrum Analyzer, packed with features for your most common tasks out in the field.
-
Product
32 Form C High Power Relay Module
DP-cPCI-4035
-
DP-cPCI-4035 is a cPCI-based 32-channel high power relay. It is designed as general-purpose module. Applications of this module include power routing, relay outputs for soft PLCs, automatic test equipment, hardware simulation and high current measurement routing.
-
Product
Auxiliary Voltage Relays
AVR
-
Type AVR volta acquisition systemscontrol/datage acuated relays are designed for indication alarm of annunciation in elextric utility application. the relays are used for data inputs to supervisory and sequential event recorders
-
Product
Almanac Time Switch
IM1754
-
Almanac Tme Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc. as per time of the day. The timer has built in Almanac timings fixed in Nonvolatile RAM so that the user does not have to programme the unit from time to time. This Almanac time switch has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contactors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
Product
Relay Test Set Type SP-I
-
Supreme Instrument Laboratories
Supreme make relay testing set is designed for site testing of protective relays which simulate in common fault conditions under which a protective relay will be called into positive function. Periodic field testing is the best way of ensuring the integrity of the protective relays. We offer our relay testing set with specific testing capacity to suit different group of protective relays. The testing set operates on single phase 230 V, A.C. 50Hz. Supply.
-
Product
Modular Relay Board
-
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
Product
PCI Reed Relay Card, 32xSPDT
50-110B-021
Reed Relay
The 50-110B-021 is a 32xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
Protective Relay Testing
-
Choose from Doble’s F6300e and F6350e External Amplifiers for your specific protection testing needs and requirements. These amplifiers are useful in high power protection testing applications when you need additional current and/or voltage sources, for critical high burden relay testing, as well as system modeling.
-
Product
Countermeasures Sequential Timing & Amplitude Tester
C-STAT
-
C-STAT, or Countermeasures Sequential Timing and Amplitude Tester, is a Firing Pulse Interval Test Set, a suite of test components designed to analyze firing pulse timing and amplitudes from a CMDS system such as ALE-47.
-
Product
Chassis - Control up to 16 Modules with as Many as 32 Two Pole Relays Per Module Allowing 1xN Multiplexers up to 1020x1, 2 Pole Muxes up to 512x1 or 2xN Matrix Configurations up to 256x2
JX/256-MF
Chassis
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
Product
Adaptive Relay Board, Virtex-6 FPGA - PCIe
Model 78624
-
Model 78624 is a member of the Cobalt® family of high-performance PCI Express boards based on the Xilinx Virtex-6 FPGA. As an IF relay, it accepts two IF analog input channels, modifies up to 34 signals, and thendelivers them to two analog IF outputs. Any signal within each IF band can be independently enabled or disabled, and changed in both frequency and amplitude as it passes through the module. The 78624 supports many useful functions for both commercial and military communications systems including signal drop/add/replace, frequency shifting and hopping, amplitude equalization, and bandwidth consolidation. Applications include countermeasures, active tracking and monitoring, channel security, interception, adaptive spectral management, jamming, and encryption.
-
Product
Resilient Positioning, Navigation, and Timing
-
Resilient PNT is the convergence of positioning, navigation and timing technology with non-traditional and emerging technology to improve the reliability, performance and safety of mission-critical applications in the air, on land, in the sea, and in space. Resilient PNT solutions are used where even the smallest discrepancy in data accuracy, availability and stability can result in a mission failure, loss of life, battlefield disadvantages, and significant economic loss.From essential timing & synchronization, to all-in-one PNT. Modular solutions based on open standards; Products made to be secure and rugged. Providing resiliency, high performance, and continuous operation in the field. M-Code available and shipping today.
-
Product
Time Domain/Fault Location Analysis For E5061B
E5006A
-
The E5006A Time Domain/ Fault Location Analysis option allows you to locate the discontinuities and mismatches of devices such as cables. By employing the gating function in the time domain and transforming the data back to the frequency domain, you can remove unwanted responses of connector mismatch in your fixture. In addition, the cable SRL (Structural Return Loss) analysis capability is provided with the E5006A.
-
Product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
-
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
-
Product
High Impedance Busbar Differential Relay
MIB
-
The MIB, a member of the M II family of economical and highly functional digital protection relays, is a microprocessor based relay that provides three phase high impedance differential protection for Substation Bus-bars of any voltage level. Use the MIB also to protect electrical machines like transformers, generators or motors against restricted earth faults.
-
Product
CASS Instrument Real Time Controller
-
External control of the Navy CASS ATE via Ethernet. Standardized graphical user interface (GUI) for individual control of each instrument independent of CASS software. Allows TPS developer or ATE maintainer to change/control instrument settings for TPS debug and instrument troubleshooting.
-
Product
Airborne Video Delay Board
MS 2006
-
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
Product
Mini-SIL Reed Relays
Series 107
-
SIL relays - Dry and Mercury wetted 0.2 inch wide packages
-
Product
Safety Relay
-
Leuze electronic GmbH + Co. KG
With the MSI safety relays, individual safety sensors can be integrated quickly and easily into the safety circuit of machines and systems. The MSI contact extensions are used both as an output extension for OSSDs and for contact multiplication for evaluation units and safety controls.
