Development Boards
See Also: Development, Software Development, Developers, Test Development
-
product
3U Hold-Up Board 200W
059-513
Hold-Up Board for 28VDC military power supplies which can provide hold up power for up to 200W for 50ms according to MIL-STD 704 / DO160.
-
product
Multi-Channel (Up to Four) MIL-STF-1760 Interface Board for Conduction Cooled PCI Mezzanine Card Compatible Computers
EXC-1553ccPMC/Px(S)-1760
The EXC-1553ccPMC/Px(S)-1760 is a multi-channel (up to four) MIL-STD-1760 interface board for conduction cooled PCI Mezzanine Card compatible computers. In addition, Checksum, SRQ bit and Header Words are supported on each channel. Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.Each dual redundant 1760 channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. The EXC-1553ccPMC/Px(S)-1760 is supplied with C drivers, including source code, and Merlin+ Windows software.
-
product
PCI/PCIe I/O & Comm Board
76C2
NAI’s 76C2 is a PCI/PCIe multifunction I/O and communication board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
PCI To CPCI Or PXI Extender Board
MS 1720
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
Combination Board Functional Test System
QT 4256 ATE
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
product
2MP HDR Jetson TX2/TX1 Camera Board
E-CAM20_CUTX2
e-CAM20_CUTX2 is a 2MP HDR camera board for NVIDIA® Jetson TX2 /TX1 developer kit. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). It enables an excellent low-light performance and can capture images even under 0.5 lux. e-CAM20_CUTX2 is based on 1/2.7" AR0230AT CMOS image sensor from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
product
RS422/RS485 Serial Boards
104-COM-8S
These are eight, four, or two-port, asynchronous, serial communication boards designed for use on the PC/104 bus. They support RS-485 and RS-422 communications. The boards may be installed in any standard PC/104 stack. Connections are made via a 50 pin IDC type right angle connector.Common applications include POS, gaming systems, machine monitoring, military and high-density networking.
-
product
RE Family Development Environment
Renesas offers integrated development environments, driver software, sample code, an evaluation kit, and flash programmers for accelerating your system development.
-
product
Mini-ITX Embedded Board with AMD® Ryzen™ APU
AmITX-RZ-G
- AMD® Ryzen™ Embedded V1000 processor family- Up to 32GB dual SODIMM socket DDR4- PCIe x16, PCIe x1, M.2 and Mini-PCIe expansion- 4x DisplayPort
-
product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
MicroComU Board
The MicroComU board is designed to facilitate the adoption and use of the microDXP. To this end, the MicroComU includes various features to support and extend the functionality of the MicroDXP board. The MicroComU is designed to mate to a MicroDXP and be used as a set.
-
product
6U VPX Board
VP62009
LinkedHope Intelligent Technologies Co.,Ltd.
VP62009 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year life cycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62009 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62009 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62009 provides 2x 10 Gigabit Ethernet for VPX Data Plane communication, 2 x8 PCIe for VPX Expansion Plane communication, 4 GbE for VPX Control Plane communication. Rich data exchange interfaces on VP62009 make it easy to build box-level or system-level solutions.
-
product
PICMG 1.0 Full-Size Single Board Computers
PICMG 1.0 Single Board Computers (SBC) features comprehensive backplane support. The Slot SBC are the most flexible and expansible solutions for industrial applications.
-
product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
TMR Switch Sensor Demo Board
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
product
IC-INT-VPX3d, 3U OpenVPX Intel Xeon Single Board Computer
IC-INT-VPX3d
The IC-INT-VPX3d is a powerful OpenVPX 3U Single Board Computer (SBC) based on Intel’s High Performance Low Power Spectrum processors for high performance embedded computing (HPEC).
-
product
I/O Wiring Terminal Boards
ADAM-3900 & PCLD Series
ADAM-3000 series consists of cost-effective, configurable, isolated signal conditioning modules. They are able to operate in harsh environments.
-
product
21 Slot VME64x 19" Rackmount Development Platform
12V21OPX98N5VCK0
Elma's System 12V family of enclosures for VITA bus architectures (VME, VME64X, VPX and VXS) provide an industrial rugged, versatile platform. Can be configured by selecting the backplane, PSU, device modules and number of slots.
-
product
Analog Input Expansion Board
MSXB 018
The MSXB 018 Analog Input Expansion Board expands 16 analog input lines to 64 analog input lines. The MSXB 018 provides 4 expansion ports that are compatible with MSTB 009 Analog Termination Boards.
-
product
Specialized 5G & LTE Development Tools
Building on our ASN.1 expertise and high-performance PER encoder/decoder, OSS offers new solutions that comply with 3GPP LTE Release 8 - 16* ASN.1 and NAS protocols.
-
product
PCI To PC104 Extender Board
MS 1717
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
product
PCI Express Serial Boards
Sealevel PCI Express serial boards utilize 120-byte FIFOs for maximum reliability in data-intensive applications. Software developed for standard PCI boards will also work with Sealevel PCI Express boards, simplifying your transition to this next-generation PCI bus. Sealevel PCIe serial boards are configurable for RS-232, RS-422, and RS-485 electrical interfaces. These PCIe serial boards are fully compatible with X2, X4, X8, X16, and X32 PCI Express slots.
-
product
A-Base Test Board Adapter
1182 and 1183
From time to time, you may find yourself needing to test A-Base meters. Or perhaps you will need to test them for the first time in years as part of a removal project. Well, TESCO can help with the A-Base Test Board Adapter!
-
product
Qseven Rev 2.1 Application Board With LVDS, HDMI, Dual LAN And Audio
Q7B301
The Q7B301 is an ultra-compact Qseven reference carrier board which measures only 100 x 72 mm - the size is slightly bigger than a credit card. The Q7B301 is perfect for small box applications such as those found in the latest digital signs, kiosks and traffic control system. This Qseven application board offers various I/O connectors and flexible expansion features to reduce the design effort to the minimum. The Q7B301 also has an extended industrial grade operating temperature range of -40ºC to +85ºC to withstand the rigors of harsh environments. Axiomtek’s new Qseven Rev. 2.1 application board, Q7B301, is compatible with Qseven module – Q7M311 which is powered by the Intel® Pentium® Processor N4200 and Celeron® Processor N3350. Customers can emulate required functions on Q7M301 as a reference design board or integrate the Q7M301 directly into their product as the application board. Its minimum footprint also enables the maximum potential. The Q7M301 is especially suited for industrial IoT applications such as industrial control, medical imaging, digital signage, gaming machines, military, and networking. The Q7B301 comes with two PCI Express Mini Card slots and one SIM card slot for wireless communication (3G/4G, GPS, Wi-Fi and Bluetooth). For enhanced or high-definition audiovisual devices, the Qseven reference carrier board supports one HDMI and LVDS interfaces as well as HD audio and 4-channel digital I/O. More I/O interfaces include two Gigabit LANs with Intel® i211AT Ethernet controller, two RS-232/422/485, one USB 2.0, two USB 3.0, one SMBus, and one I2C. Furthermore, it has one SATA-600 interface for storage requirements.
-
product
MORA Ready Development Platform: CompacFrame Integrated With SOSA Aligned PICs And Sciens Innovations Helux Core RF Tools
SE9M3PS9YIBXNLY
The MORA-Ready Development Platform (MRDP) simplifies the process of creating RF signal processing capabilities and accelerates integration of existing applications. Featuring Sciens Innovations helux™ Core powerful software tools to accelerate RF signal generation and system development.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 6 MiniPCI Express Modules
SKU-085-31
PCI Express Carrier board for 6 MiniPCI Express modules was designed to expand modern motherboards with PCI Express interface. It is the first carrier board in the Squid family with MiniPCI Express 2.1 and PCI Express Gen 3 Specifications support.
-
product
16-bit, 200KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3016-4
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
product
FPGA DSP Board
Renice has developed part of the FPGA evaluation board, which can be used as high-speed signal processing board, wireless communication board and image processing board. By default, it’s equipped with Altera FPGA (StratixIV), high-speed ADC/DAC, USB Controller and SODIMM Connector.
