Ghost Detectors
Measure magnetic flux density/field strength.
-
product
Carbon Monoxide Detector Tester
Solo C3
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
product
Freezing Rain and Ice Detectors
Freezing-rain and ice detectors detect the presence of icing conditions so that appropriate actions can be taken to prevent damage to power and communication lines, to warn of road hazards, to keep ice off a plane’s wings, and to prevent ice from forming on turbine blades.
-
product
Fixed Gas Detectors
OLCT 10 - OLC 10
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
product
Electromagnetic Field Detector
LCD display3 Digits LCD With 1999 Counts Low Battery Display On LCD Overload"OL" Display On LCD Accuracy(3%+3dgt) at 50Hz./60Hz. Frequency Response30Hz~400Hz Sampling RateApprox. 2.5 times/sec. Max Hold / Data Hold Battery9V x 1 Specifications0.1~200mG (milli Gause)
-
product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
product
Refrigerant Leak Detector
755
0.1 oz per yr sensitivity. Powerful Diaphragm Pump. Soft Case with Shoulder Strap. Mute and Battery Check Buttons
-
product
Ultrasonic Flaw Detector
MFD350B
Based on ultrasonic principle, digital ultrasonic flaw detector MFD350B with 320*240 TFT LCD, it can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. It can be used in Laboratory as well as in engineering filed. With range of 0-6000mm, it can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium battery module, it can be long standby for months. High quality with low price, it is the first choice for the practical economic model for ultrasonic testing equipment.
-
product
Ditert-Butyl Peroxide Residue Detector
DRK-GC-7890
Shandong Drick Instruments Co., Ltd.
Melt-blown cloth has the characteristics of small pore size, high porosity and high filtration efficiency, and is the core material of mask production. This instrument refers to GB/T 30923-2014 plastic Polypropylene (PP) Melt-blown Special Material, suitable for polypropylene as the main raw material, with di-tert-butyl peroxide (DTBP) as the reducing agent, modified polypropylene melt-blown special material.
-
product
Analog Ionizing Radiation Detectors
A great general purpose analog radiation detector. Detects from 0-50 mR/hr.
-
product
Stealth Web / Textile Metal Detector
Stealth Web metal detectors are custom manufactured to inspect products typically sheeted or on a roll / web. Stealth web detectors are ruggedly built to ensure product integrity and provide machine protection against metal fragments. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants.
-
product
Fixed Gas Detectors
DG7 Series
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
product
Digital Ultrasonic Flaw Detector
Are modern age portable and processor-based flaw detectors. They are made up of parts including an ultrasonic transducer, hardware & software for capturing signals and analysing them, a data logging module, and a waveform display for viewing the images and graphs.
-
product
Partial Discharge Detector
PXDP-II
The PXDP-II partial discharge meter is a portable device that performs detection and measurement of partial discharges in electrical devices or components. It records partial discharge measurements for analysis and diagnosis through the optional PC software. The PXDP-II can be used in various applications and complies with IEC 60270.
-
product
SF6 Gas Purity Detector
JH4000CD-1
Xiamen Jiahua Electrical Technology Co.,Ltd
Purity of SF6 gas is not only a major item for gas quality acceptance and evaluation of equipment installation and maintenance process, but also a reliable accordance for internal troubleshooting. According to gas purity changes, it can be judged whether the equipment has any serious fault.
-
product
Silicon Detectors
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
-
product
Mini Carbon Monoxide Gas Detector
Model - KM CO-910
Kusam Electrical Industries Limited
KM-CO-910 Carbon Monoxide meter detects the presence of Carbon Monoxide (CO) & measures concentrations between 1-1000 parts per million(PPM). The meter indicates the presence of CO by a reading on the LCD & a beeper tone. The beeper function much like clicking of a geiger counter: above 200PPM, the beeper sounds continuously with the concentration of CO; from 35PPM to 200PPM, the beeper sounds discontinuously with the concentration of CO.
-
product
VUV Spectroscopy Detector
All gas phase molecules absorb strongly in the vacuum ultraviolet region (120 – 240 nm), yet application of VUV absorption technology to routine analytical detection and measurement has not been addressed…until now. The VGA-100 is the world’s first benchtop VUV spectrometer. It is a universal mass-sensitive gas chromatography detector that provides both qualitative and quantitative data. The strong absorption of gas phase molecules in the VUV spectrum provide excellent sensitivity, and the compound-specific absorption spectra provide unparalleled selectivity.
-
product
Light Meters, Detectors, UV-VIS-NIR Radiometers
Devices and systems for photometric, radiometric and colorimetric measurements of light and optical radiation. Light Meters and Radiometers for different applications like UV radiation, Laser measurements, LED measurements, photomedicine and much more.
-
product
MPI Flaw Detectors
A non-destructive testing method that can detect surface and subsurface flaws in ferromagnetic materials.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 LCC
A single-channel silicon-based thermopile in a LCC package for surface mount assembly in a small active area of 0.61mm x 0.61mm. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature chang
-
-
product
Pyroelectric Detectors
Pyroelectric detectors are thermal detectors; i.e. they create an electric signal due to temperature changes in the chip. This temperature change is caused by absorption of light. We do use LiTaO3 and DLaTGS as pyroelectric materials. Basically such detectors cover the whole spectra. However, they are mainly used for mid-wave and long-wave infrared detection (MWIR and LWIR). In addition, the usage in the THz region seems to become more popular these days.
-
product
Voltage Detectors & Others
Voltage Detectors, Circuit Breaker finder, Portable working lamp are Indispensable equipment which must always accompany the technician. Its essential characteristics are an extreme handiness, a very high protection degree and easiness of use.
-
product
Micro Capacity Type High-Speed Rotation Torque Detector
TH-3000/3000H Series
TH-3000 series is a torque detector designed for very low torque (less than 2 N· m) with high response and high accuracy. Two types are available depending on your applications.
-
product
Holiday Detector
266
The Elcometer 266 Holiday Detector revolutionises high voltage DC testing of coatings porosity detection making it safer, easier and more reliable than ever before.
-
product
Metal Detectors
In our ever-changing landscape, important assets are buried or paved over making finding for them both difficult and time consuming. Valve and manhole covers are often lost after ground work activities, re-surfacing or after heavy snow falls. Buried boundary markers can also be difficult to find. Most of these items are manufactured using magnetic or ferrous materials. These can be detected using the VM-880. As it detects only ferrous materials, aluminum cans, bottle caps, etc. are rejected. The simple audio and visual user interface has been designed to minimize training requirements while the latest technologies are employed to ensure maximum sensitivity and depth range. Particular attention has been made to ensuring the weight of the VM-880 is minimized, at just 1.54lbs (0.7kg), it is by far the lightest in its class. This has been achieved without compromise to strength. The submersible carbon fiber antenna tube is both lightweight and provides maximum protection to sensitive sensors.
-
-
product
H-Field Burst Detector
BD 11
The BD 11 is used to detect a burst or ESD current pulse on a cable, for example in a complex system. This makes it easier to investigate the causes of sporadic faults in the system. It is small and handy, its sensitivity is very high and continuously adjustable.
-
product
Low-Barrier Schottky Diode Detector, 0.01 to 18 GHz
33330B
The Keysight 33330B low-barrier schottky diode detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking.
-
product
Thin Film Based Thermopile Detector: 3 Channels, Compensated
T34 Compensated
A three-channel compensated (6 element) thin-film thermopile in a TO-8 package. Each active area is 3.16mm x 0.4mm. Offers thermal compensation to minimize effect of sudden ambient temperature change. Internal aperture minimizes channel-to-channel crosstalk while increasing sensitivity.
