-
Product
Manual Fixture Kit
230356 – CMK-07
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Miniature Probes with Cords
Stat MP-1234
-
This optional probe is used with the Ohm-Stat RT-1000 Standard Resistivity Tester. It accurately measures surface resistivity and conforms to the EOS/ESD 11.11 specifications.
-
Product
DMM Test Probe Kit With Multi-Stacking Banana Plug
5325A
-
DMM test probe kit with multi-stacking banana plug
-
Product
Temperature and Humidity Regulator
H3431-4
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 230gf
K100-C150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Two Inputs Thermocouple Thermometer
HD2328.0
-
Thermocouple thermometer for probes type K, J, T, E. It measures temperature by means of immersion, penetration, contact or aria probes. Two inputs for miniature thermocouple connectors. Storage of maximum, minimum, average value. Functions: REL, HOLD and auto power off which can be disabled, IP 67 protection degree.
-
Product
Measuring Arms
-
Among the highly ergonomic and portable scanning and probing solutions that QFP offers are the KREON arms , a range of tools capable of operating on different working volumes (approximately from 2 meters with the ACE 6-20 model to 4.5 meters with the ACE 6-45 model) applicable in different sectors.
-
Product
Chemitec Sensors And Analyzers To Monitor Oxidants In Water
-
Chemitec's S494 series of amperometric probes provide continuous, accurate monitoring of chlorine and other oxidants in clean water applications. A range of sensors assures accurate measurement of oxidation, with sensors optimized for Chlorine (total, organic or inorganic), Chlorine Dioxide, Ozone, Peracetic Acid, Hydrogen Peroxide, Bromine, or Chlorites.
-
Product
Pyramid, 3-Sided Chisel 30°, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0T
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
Product
ITA, I1, With Protective Cover
410128101
ITA
The i1 ITA's small width and inboard handle increase the side to side stackability. The U-shaped cable clamp allows modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.07 in. The removable cover allows easy access to wiring for maintenance and probing. Protective Cover included.
-
Product
Standard 1.00 (28.30) - 5.40 (153.00) Battery Probe
BIP-10
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Resistance Remark: Probe Resistance Steel: 30 mOhms, Gold plated: 100 mOhmsTest Center (mil): 260Test Center (mm): 6.60Full Travel (mil): 157Full Travel (mm): 4.00Recommended Travel (mil): 126Recommended Travel (mm): 3.20Overall Length (mil): 591Overall Length (mm): 15.00
-
Product
Mixed Domain Oscilloscope
3 Series MDO
-
With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the 3 Series MDO sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the 3 Series has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.
-
Product
Wide-Range Temperature Probe
Go Direct™
-
Vernier Software & Technology, LLC
Designed to be used as you would use a thermometer for experiments such as the recrystallization of benzoic acid, simple and fractional distillations, determination of boiling points, the synthesis and analysis of aspirin and other organic compounds, and more. Range of –20 to 330°C allows for investigations such as determining the melting point of caffeine or the boiling point of different vegetable oils. RTD (Resistance Temperature Detector) technology establishes a ±0.5°C accuracy.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1L-4
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
UV Light Meter
Model 308T
-
Built for high intensity applications the NEW OAI Model 308T UV Light Meter is a dependable, direct-reading instrument designed for measuring UV light intensity for UV curing. The Model 308T features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port. Accuracy of the meter is within ±3%and measurement repeatability is within ±3 LSB (least significant bit). Like all OAI precision instruments, the Model 308T provides NIST traceable measurements. This easy-to-use meter is auto-ranging from 0.1 to 1999.9 milliwatts/cm2 full scale when used with the 2000 milliwatts/ cm2 probe. The linearity of the meter in this range is at least ±(.002% + 6 LSB).
-
Product
Time Domain Sensors
TDS
-
Schmid & Partner Engineering AG
Time Domain Sensor (TDS) probes are miniaturized fully isolated active optical magnetic or electric field sensors operating in the frequency range from 10MHz to 6GHz. TDS offers unparalleled sensitivity for EM measurements resolved in the time and frequency domains while maintaining all amplitude and phase information.
-
Product
LCR-Reader-MPA: Ultimate All-in-One Digital Multimeter
-
LCR-Reader-MPA combines tweezer probes with a powerful LCR/ESR-meter that is able to determine the type of component and best test parameters before measuring with a 0.1% basic accuracy. The device will display the main impedance value, any secondary values such as ESR, Q or D, component type and test parameters used instantly on a bright backlit LCD display. The 1 oz. device is very portable and ideal for fieldwork.
-
Product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe
LFRE-1B-7
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
K-type Thermocouple to Digital Converter
THERMO K click
-
THERMO K click carries the MCP9600 IC from Microchip. Depending on the type of probe it uses the click can measure temperatures from −200 °C to +1372 °C.
-
Product
Extreme Temperature Passive Probe
N7007A
Oscilloscope Probe
Many environmental test engineers today are using standard-temperature probes in extreme temperature condition, which causes physical damage to the probe. Another common practice among environmental test engineers is to simply attach long wires at the end of their probes, which significantly degrades measurement performance due to excessive inductance and reduced bandwidth. Keysight addresses this issue with the N7007A single-end passive probe.
-
Product
Coordinate Measuring Machines
-
Coordinate Measuring Machines (CMMs) measure the geometry of physical objects by sensing points on the surface of the object with a touch probe. They are commonly used in manufacturing processes to inspect a physical part or assembly against the design specification.
-
Product
Standard 1.50 (43.00) - 3.00 (85.00) General Purpose Probe
P2665G-1R1S
General Purpose Probe
Current Rating (Amps): 15Average DC Resistance lower than (mOhm): 10Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 230Full Travel (mm): 5.84Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,290Overall Length (mm): 32.77Overall Length Remark: Tip 2W: 1270 mil (32.26 mm)
-
Product
Cryogenic Applications
-
Over the last 20 years the Celadon Engineering team has developed an expertise in cryogenic materials which has resulted in a solid reputation in the industry for producing extremely stable cryogenic on-wafer probe card as well as DUT probing solutions. These custom cryogenic probe card solutions are widely used to test Space, Military, Medical and Quantum Computing products. Celadon’s cryogenic solutions vary from standard VersaTile™ footprints which interface to positioners to innovative custom PCB based designs to allow for flexibility when testing at these very cold temperatures. Lakeshore cryogenic wire is used in standard DC solutions for high density cableout designs to support high pin count applications. During the development process, Celadon works closely with the cryogenic prober vendor to ensure the integrated solution is optimized for current and future testing needs.
-
Product
Compact Monitoring Probe
ISDB-T/Tb
-
Network operators:automate the tests of new transmittertemporary monitoring/investigation toolrebroadcasting receiver: RF to ASI or IPBroadcasters: off-air monitoring probe to validate the on-air contentTV/STB producers: automated tests against a professional receiverLabs: easy & simple access to live DTV sources via RF
-
Product
High 1.50 (43.00) - 9.60 (272.00) Long Travel Bead Probe
BPLT-1HF-9.6
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,450Overall Length (mm): 36.83Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, High Spring: 350 mil / 8,89 mm
-
Product
Transversal-Hall-Probe
-
For the Gaussmeters are several transverse Probes with different dimensionsand sensitivity available.
-
Product
Elevated 1.68 (4.00) - 7.00 (198.00) Bead Probe
BTP-1HC-7
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Temperature and humidity duct probe
T3113
-
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Infiniium V-Series Oscilloscope: 20 GHz, 4 Analog Channels
DSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Changeable Cassette
230373/1 – CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
