-
Product
Probes
-
D-COAX offers four analytical probe models: HyPac model for package characterization, and two models, Omni and OmniJet, for board level characterization, and DP1.4mm diffenrential, single-ended probe.
-
Product
ICT Probes
Merica Series-MPAL50
-
Minimum Center: 1.27(50mil)Current Rating: 3amps, continuousCurrent Resistance: 60milliohmsFull Stroke: 6.35mmRated Stroke: 4.30mmSpring Force: 185/227gf(7/8oz)
-
Product
Fiber-Optic Probes
Fiber-optic Probe
Designed with an unparalleled optical quality finish, Optomistic Products has developed a wide array of Fiber-optic Probes to accommodate your specific LED test requirement and mechanical constraints.
-
Product
Thermocouple Probes
Type T
-
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
Product
IsoVu Isolated Probes
-
The IsoVu Measurement Systems can make nearly impossible measurements – like high-side Vgs- a reality, providing today’s power engineer with measurement insights not available in other power systems and instruments. When performing near-impossible measurements, especially in those involving Gallium Nitride (GaN) and Silicon Carbide (SiC), it can be extremely time consuming and cumbersome. IsoVu eliminates those concerns: IsoVu probes offer better common mode rejection and higher bandwidth for high EMI environments and on power FETs like SiC and GaN.
-
Product
Temperature Probes
-
Lake Shore offers a variety of temperature sensors in packages that enable mounting in very tight areas. But for some applications (especially if the sensors have to be immersed in liquid), you need to do more to protect the sensor circuitry. For these applications, a cryogenic temperature probe is the optimum choice. Encased in one of these stainless steel thermowell fixtures, the sensor can perform as designed, is unaffected by high pressure, and is sealed to keep electrical components and wiring protected from fluids and other elements.
-
-
Product
Power Probes
RkT Thermopile Series
-
The RkT Series thermopile power probes are ideal for measuring Nd:YAG, CO2, and other mid-power lasers. The probes are designed to withstand average power densities up to 20kW/cm2 (15MW/cm2 peak pulse power density). The flat UV to far-IR spectral response allows the probes to measure broadband sources as well. Measure the power of cw sources or the average power of sources pulsed at 5Hz or greater.
-
Product
ICT Test Probes
-
C.C.P. Contact Probes Co., LTD.
Our In-Circuit Test Probes are used for all kinds of PCB tests. We offer a standard portfolio as well as customized parts.
-
-
Product
Energy Probes
RjP-700 Series
-
The RjP-700 Series probes are designed to measure lower pulse repetition rate, longer duration pulses - up to 1msec pulse width at a maximum rep rate of 40Hz. This allows for measurement of pulsed flashlamps and other sources not possible with other probes. The combination of large area detector surface and long pulse width allow for measurements up to several Joules total energy. Integrated preamplifiers allow for longer probe-to-instrument cable runs, useful for manufacturing environments.
-
Product
Hall probes
-
Axial, transverse, multi-axis, and tangential Hall probes for measuring magnetic flux density. Choose from a wide range of lengths and thicknesses—probes are also available for cryogenic applications.
-
Product
ICT Probes
-
ICT Probes - Test Center: 50 - 100 milsCurrent Rating: 3 - 5 ampsContact Resistance: 30 - 50 milliohmsSpring Force: 113 - 312 gf (4-11 oz)
-
Product
Raman Fiber Probes
-
For ultimate flexibility, fiber-coupled Raman probes offer a compact design and a rugged, robust construction for a wide range of applications. With an optional integrated camera, the user can locate a precise region of interest prior to analysis. Also available are immersion probes and non-contact optics.
-
Product
Interface Probes
-
Low resistance used in: *ICT Testers *Functional Testers *Special Purpose Machines
-
Product
Battery Probes
Battery Probe
*Charging *Connecting *Docking Station for *Medical- IOT - Communication
-
Product
Probes PH
-
Durable sensors designed for continuous, in-line measurement of acidity or alkalinity in industrial liquids.
-
Product
BTP-25 Bead Probes
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
BIP-3 Battery Probes
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 60Recommended Travel (mm): 1.52Mechanical Life (no of cyles): 250,000Overall Length (mil): 511Overall Length (mm): 12.98
-
Product
Differential Probes < 1.5GHz
-
Differential active probes are like two probes in one. Instead of measuring a test point in relation to a ground point (like single-ended active probes), differential probes measure the difference in voltage of a test point in relation to another test point
-
Product
Accessibility Test Probes
TF-24 Series
-
Accessibility Test Probes are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
Product
Gold Probes
4900 Series
-
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
Product
CP-2XX-12 Battery Probes
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 128Full Travel (mm): 3.25Recommended Travel (mil): 118.1Recommended Travel (mm): 3.00Overall Length (mil): 472Overall Length (mm): 12.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Probes
71 Series
-
American Probe & Technologies, Inc.
10 mil (0.010") shank sizesAvailable in straight and bent shapes
-
Product
Thermocouple Probes
-
sensor that measures temperature. It consists of two different types of metals, joined together at one end. When the junction of the two metals is heated or cooled, a voltage is created that can be correlated back to the temperature.
-
Product
Test Probes / Test Fixtures
-
INGUN has an unbeatable assortment of test probes and test fixtures for individual testing tasks.Thanks to many years of experience in the testing equipment field, INGUN offers the suitable test solution for every test requirement.
-
Product
Flexible Magnetic Field Probes
-
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
Product
CP-2XX-4 Battery Probes
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 39Full Travel (mm): 1.00Recommended Travel (mil): 30Recommended Travel (mm): 0.75Overall Length (mil): 158Overall Length (mm): 4.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Current Measurement Probes
-
Comprehensive line of clamp-on current probes covers the entire spectrum of applications, from electrical panels to substations. AEMC Current Probes measure current without interrupting the circuit under test and extend the measuring capabilities of DMMs, recorders, power meters, and loggers. The numerous jaw sizes are designed to accommodate a wide variety of conductor diameters and ranges. Available for AC or DC measurements.
-
Product
Probes
Hygro-i Series
-
The Tramex Hygro-i ® relative humidity probe is the most advanced, resilient and reusable RH probe on the market today. Used in conjuntion with Tramex CMEX II and MRH III moisture meters, the Hygro-i ® relative humidity probes allow the user to perform in situ and hood type RH testing to comply with ASTM F2170 and British Standards BS 8201, 8203, 5325 for the Flooring Industry, and is ideal for use by Flood & Water Damage Restoration and Indoor Air Quality professionals.
