Product

Probes, Clamp-On

EM-6980 | 20 Hz – 50 KHz

-

Electro-Metrics Corp.

EM-6980 | 20 Hz – 50 KHz - Electro-Metrics Corp.

Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.

Product

Optical Probes- High Bandwidth

DPO7OE

-

Tektronix, Inc.

DPO7OE - Tektronix, Inc.

The DPO7OE series optical probes with a DPO70000 real-time scope deliver the performance and advanced debug capabilities designers need to fully troubleshoot 400G PAM4 signals, up to 56 GBaud, and reduce time to market.

Product

Special Purpose Probes

6100 Series

-

Probe Master Inc.

6100 Series - Probe Master Inc.

Similar to a standard 10X scope probe except with BNC connections on both ends. With BNC connections on both ends, it provides a more stable connection when connecting to other equipment. This eliminates the use of a standard probe with a BNC adapter on the probe end that could come loose or break off the probe tip. The lead can be compensated to your scope with the trimmer tool included.

Product

High Impedance Active Probes

12C

-

Picoprobe

12C - Picoprobe

A high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf and the rise/fall times are 0.8 ns. This instrument has full dc capability and can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 and with a 50 Ohm input, signal attenuation is 20:1.

Product

Probes, Magnetic Field

EM-6882 | 20 MHz To 230 MHz

-

Electro-Metrics Corp.

EM-6882 | 20 MHz To 230 MHz - Electro-Metrics Corp.

The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.

Product

ProBus Probe Adapter for TekProbe-BNC Probes

TPA10

-

Teledyne LeCroy

TPA10 - Teledyne LeCroy

- Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope- Automatic probe detection- Provides all necessary power and offset control to the attached probe- Supports probes up to 4 GHz- Easy firmware updates- Wide variety of probes supported including: Preamplifiers, Current Probes, Single-Ended Active Probes and Differential Active Probes

Product

DDR4 MSO Probes

-

FuturePlus Systems

FuturePlus Systems

The DDR4 DIIM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR4 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR4 signals for convenient analog probing. The user can then easily observe both the digital and analog representation of the DDR4 Address, Command and Control bus. Solder down N5541A analog probes purchased separately from Keysight Technologies.

Product

Multi-Purpose Probes

-

Equip-Test Kft.

Equip-Test Kft.

*For All your Functional Test Needs *Machine Building *end of line test

Product

Probes With Integral Connectors

-

Omega Engineering, Inc

Omega Engineering, Inc

Used when quick and easy removal and installation are important requirements at the measuring device. Available in quick-connect, terminal block, m8, m12, and other popular connector styles.

Product

T3CP Series AC/DC Current Probes

T3CP Series

-

Teledyne LeCroy

T3CP Series - Teledyne LeCroy

Teledyne Test Tools AC/DC Current Probes are powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range of five current probes includes models with bandwidths up to 100 MHz, peak currents up to 500A and sensitivities to 1 mA/div.

Product

Other Passive Probes

-

Texas Co.

Texas Co.

Probes connect the input of the oscilloscope to test points on the device under test (DUT). There are many types, including: high impedance passive, low capacitance, single-ended active, differential active, high voltage, and current probes. This is the first in a series of three articles on probe selection and application, and will focus on passive probes. Part 2 and part 3 will address active probes and current probes, respectively.

Product

Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 197 x 114 mm (wxd)

CMK-05

-

Columbia Elektronik AB

CMK-05 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

Linear Polarization Resistance Probes

-

Metal Samples Company

Metal Samples Company

Linear polarization resistance (rosion probes are commonly used in the water treating industry and other environments where instantaneous, on-line corrosion rate readings are required. Linear polarization probes are ideally suited to monitor fluctuations that may occur within a system; for example, these probes can be used to monitor corrosion inhibitor effects on a regular basis.

Product

Waveguide Probes

-

Vidyut Yantra Udyog

Vidyut Yantra Udyog

We are a leading Manufacturer & Exporter of Waveguide Probes such as Tunable Probe and Waveguide Matched from India.

Product

Passive Probes

-

Teledyne LeCroy

Teledyne LeCroy

Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a /10 attenuation and feature a high input resistance of 10 MOhm. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400 V, some as high as 600 V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.

Product

Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 1000 Units, Max UUT 450x330MM (wxd)

CMK-07

-

Columbia Elektronik AB

CMK-07 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs. 10 mm ESD-proof top cover with aluminum reinforcement bars. Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

T3 Low & High Voltage Differential Probes

T3 Series

-

Teledyne LeCroy

T3 Series - Teledyne LeCroy

Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.

Product

Probe Kit for PPE Series, PP005 and PP065 Probes

PK106

-

Teledyne LeCroy

PK106 - Teledyne LeCroy

Probe Kit for PPE Series, PP005 and PP065 Probes.

Product

Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)

CMCSK-03-01

-

Columbia Elektronik AB

CMCSK-03-01 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

OEM Raman Miniature Probes

-

HORIBA, Ltd.

HORIBA, Ltd.

- Minimum Range: 210cm-1, up to 4000 cm-1 however limited by spectrometer range- Optical design: Bandpass and longpass filters in proprietary layout- Fiber coupling: FC connectors- Fibers: Typically 100µm single fiber for Laser Excitation, TBD for Signal Collection- Spot Size: 100-125µm on sample (**Other spot sizes on request)- Working Distance: 9 to 10mm- Dimensions: 106 x 21 x 33mm / 4.2 x 0.9 x 1.3mm

Product

Test Probes

E-Series

-

Equiptest Engineering Pte Ltd

E-Series - Equiptest Engineering Pte Ltd

Your product descriA full portfolio designed for general purpose test on bare boards, surface mount assemblies and other forms of test specially to meet any needs.ption goes here.