GPIB Interfaces
-
Product
Network Interface
-
VadaTech offers AMC Network Interface Cards (NICs), FMC networking modules and ATCA rear transition modules (RTMs) with a wide range of connector interfaces to make it easier for you to integrate an embedded computing system into your solution.
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
Product
USB-C Thunderbolt™ 3 Appliance with Two Independent, Dual Redundant 1553 Busses, Eight ARINC-429/717 Channels, 4 RX/TX & 4 RX
TBOLT-MA4
USB Interface
Full Featured and Native 1553 and ARINC Thunderbolt interface! Full PCI Express interface – same advanced interface as PCIe backplane cards in a small, portable, rugged appliance.
-
Product
Isolated Serial Interface Card
PCI-ICM-2S
-
The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
Interface
EPMC-1553-8
Interface
Abaco Systems EPMC-1553-8 is the first PMC (PCI Mezzanine Card) module to offer 8 dual redundant MIL-STD-1553B Notice II channels. Available in commercial, ruggedized and conductively cooled versions with eight dual-redundant channels, the EPMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
ECU Interfaces
-
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
Product
Interface Between the Operator and the Sensor
Controller
-
The high-resolution touch screen provides best technical comfort and a virtual keyboard, including Latin, Asian and Cyrillic characters. A real time chart shows the trends and provides quick and clear information about the current process cycle, while the menu and display functions are clearly laid out. The user interface is intuitive and simple to use. Password-protected user administration and a stable, comprehensive data memory for all process values and events ensure the traceability, reliability and safety of the system.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
Serial Interface
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
Analog and Digital Interface
421
-
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
Switch Module
Industrial Programmers Interface up to 8 targetsRelay BarrierDemultiplexer module up to 32 devicesCommunication Interfaces I2C and SPI
-
Product
TTENetwork Interface Cards
-
The TTENetwork Interface Cards are pluggable mezzanine cards for network communication combining regular Ethernet with the safety-critical time-triggered technology from TTTech. They enable real-time Gbit/s Ethernet communication between a computer and TTESwitches for redundant channels in a safety-critical way.
-
Product
Interface Cards, Cables, and Modules
-
Keysight Technologies Interface Cards, Cables, and Modules
-
Product
Verifier Computer Interface Report
VCIR
-
The Verifier Computer Interface Report (VCIR) is a Windows software package that allows for transferring inspection report from your Inspector series bar code verifier to a computer. Once transferred you can review the ISO/ANSI inspection results or view the scan reflectance profile for detailed troubleshooting. The inspection results can be saved by job for later retrieval or to append new inspection results to the existing job. As each job is saved an Excel spreadsheet (CSV file) is generated. You can customize which parameters should be saved in the spreadsheet. The spreadsheet provides a simple report that will have a line for each bar code inspected.
-
Product
PXI-8512, 1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-01
CAN Interface
1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Interfaces & I / Os
-
USBTucan is a USB-connected I / O box with digital inputs / outputs, analog inputs and a galvanically isolated CAN interface.
-
Product
3U cPCI Sensor Interface Unit
SIU33
Sensor Interface Unit
NAI's SIU33 is a highly configurable rugged COTS system or subsystem ideally suited for rugged military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU33 uses up three NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
Product
GPIB to Relay Minibox™
Model 4864
-
* Model 4864-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Optional terminal board and terminal strip for easy connections without soldering. See the GPIB Accessory page. * Model 4864-12 provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as listed for the 4864-11. * Model 4864-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as listed for the 4864-11.
-
Product
Test Interface Solutions
-
As the leading independent provider of pick-and-place handler change kits, we provide the best quality and affordable kit using only the most robust materials.
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
PCIe X8 Interface
96VG-NG730F16-3A
Interface
NVIDIA GT730 Kepler GPU Architecture. Integrated with 1GB DDR3 64-bit memory. Supports up-to 4 Monitors with HDMI. 1 Slot Compact design for industrial chassis PCIe x8 interface.
-
-
Product
CAN interfaces and Analysers
-
CAN interfaces and analyzers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
Product
GPIB To Ethernet Instrument Interface
-
*ICS's 4865B GPIB to Ethernet Instrument Interface adapts instruments with Ethernet interfaces to GPIB test systems.*ICS's 4865B provides a VXI-11 compliant interface for instruments that support the VXI-11 protocol and a smart, user-configurable, raw socket protocol that accommodates most instruments that use raw sockets. The 4865B replaces our earlier Model 4865 and is 2x to 5x faster than the original Model 4865. Click here for the original 4865 webpage.
-
Product
FRP-25T Test System Interface Probe
FRP-25T
ICT/FCT Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 120Recommended Travel (mm): 3.05Overall Length (mil): 1,210Overall Length (mm): 30.73
-
Product
USB 3.0 Interface Module
-
SuperSpeed "USB 3.0 modules" for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 3.0 link untouched.
-
Product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
-
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
Product
Pulsar 4 Channel Interface
Pulsar-4 7Z01201
-
Ophir’s 4 channel Pulsar interface turns your PC or laptop into a full fledged Ophir multi-channel laser power/energy meter. Just install the software, plug the laser measurement sensor into the Pulsar and the USB cable from the Pulsar to the PC USB port. With the Pulsar-4, you can connect up to 4 laser measurement sensors to each module, monitor each pulse at up to 25 kHz and utilize external trigger.
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
Controller
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
Data Interfaces, Sensors And Actuators
-
Dewesoft also develops and manufactures data interfaces such as CAN USB devices, GNSS and INS positioning devices, and Inertial Measurement Units (IMU), and high-speed cameras. All devices are completely compatible and synchronized with all of our Data Acquisition (DAQ) systems and offer the same highest possible built quality. To complete the measurement chain we also provide high accuracy current and vibration sensors.
