Shielding Effectiveness
the ability to block an electromagnetic field.
See Also: Shielding, RF Enclosures
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Arduino CAN Shield
IFB-10003-AWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Hall Effect Proximity Switches/Sensors
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
Original VXI Module Shield Kits
11399x Series
-
* Clamshell design fits C-size modules with 96-pin connectors.* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Component side shield has an address switch opening and non-rectangular mounting hole pattern.* Complimentary layout support includes PCB design template and CAD layout files.* RECOMMENDED FOR LEGCY APPLICATIONS ONLY due to its non-rectangular hole pattern.
-
Product
Hall Effect Measurement system
HMS-5000
-
Constant current source + Van der Pauw method terminal conversion system
-
-
Product
Hall Effect Magnet Kit
-
Permanent magnet - Neodium materials - +/- 0.03Tesla deviation can be made in a process of assembling magnet. - However, we indicates correct tesla strength measured by gaussmeter, before shipping magnet kit.
-
Product
Shielded and Unshielded Cable
-
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
Product
Rotary Hall Effect Sensor
-
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
Product
MIMO Antenna Assembly for Shield Box
HDRF-MIMOST2570
-
MIMO Antenna setup assembly customized for HDRF-series shield boxes
-
Product
Hall Effect Sensor
-
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
Product
Shielding Cube
CMQ200
-
The R&S®CMQ200 is a compact and fully integrated solution to cover most 5G devices in various applications. The drawer concept enables fully automated handling in manufacturing environments. The robust mechanical design ensures millions of test cycles for reliable mass production environments. The flexible cube design covers applications for smart devices, CPEs, RFIC and prototypes. R&S®CMQ200 is ready for 5G and other technologies in the frequency range from 20 GHz to 77 GHz.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
RF Shield Box
-
A small versatile manual shielding box that is designed for small scale device testing such as wireless network cards and wireless communication equipment.
-
Product
Arduino CAN Shield
IFB-10003-ANP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Hall Effect Thickness Gage
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
Dual RF Shielded Test Enclosure
JRE 0814-2R
-
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R is ideal for testing devices with a tall form factor. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
Shield Level / Pathloss Equipment
PAMS & PAMS-C
-
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
Product
CAN-BUS Shield
-
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output it to a screen to make an in-dash project.
-
Product
Icon Series Audio Effects Plug-Ins
-
Out of The Box Thinking for In-The-Box Producers. Delay, Reverb, Compressor and EQ Plug-Ins with Dedicated Hardware Controllers.
-
Product
Standard Round 2m Cables, Shielded, for Higher Current
ST010-S
-
Connection to digital boards, intended for higher currents. to be used with CPCI-1500, APCI-1500, APCI-1564, APCI-2032.
-
Product
SCSI-68 Shielded Cable
PCL-10168
-
Weight :240gDouble-shielded cable with SCSI-II 68-pin male connectorInsulated half pitch 68pin copper alloy gold plated male connector with thumb screw34 twist pairs tinned and strand copper wire with drain wireAluminum/Mylar foil and braided copper double-shielded cableP.V.C. jacketUL 2919 approvedColor :Grey
-
Product
Arduino Shield Header Kit
INT-19002
-
Complete header set for Arduino Uno shields. Contains: 1 1x6, 2 1x8, 1 1x10, and 1 2x3 header. These headers have square pins and fit into standard 0.1" breadboards. Gold plated and RoHS compliant.
-
Product
Quadruple Function Tester with Shielded HF Test Chambers
UTP 9011 RF
-
Circuit boards are the heart of all electronic devices. To ensure the reliable function of these boards, detailed tests are essential.Our board-level tester UTP 9011 RF works safely, quickly and cost-optimized at circuit board level. Our interchangeable adapters are particularly efficient in this system, with which you can even test different test items at the same time. The shielded NOFFZ HF test chamber always ensures consistently good results.
-
Product
Super high temperature hall effect measurement system
-
Super high temperature hall effect measurement system that is useful to flow gas into chamber with sample. - Newly developed furnace that makes it possible to increase over 800 and use for measuring hall effect. - Gas flow control system in order to flow various gas. - Sample holder for high temperature. (keep the good contact on 800) - High Temperature control system (DC power) On condition of specific temperature with gas flow , new semiconductor materials have been developed to see electrical property's change.
-
Product
Hall Effect Sensors
-
A new range of sensors based on closed loop hall effect technology, for measuring and monitoring of e.g. secondary transformer overload or shortcircuit detection, DC link from ground fault and overload, motor overload.
-
Product
RF Shielded Test Enclosure, for Laptop Testing
JRE 2218
-
Breeze through laptop RFI and wireless tests with the 'bigger than-a-breadbox' 2218! Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan.
-
Product
RF Shield Box
LTL R21001
-
Liveon Technolabs LTL R12001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL R12001 RF shielded test enclosure can comfortably house the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.
-
Product
SCB-100A Noise Rejecting, Shielded I/O Connector Block
785024-01
-
100-Pin Female SCSI to 100-Pin Female Screw Terminal, DIN Rail, Wall, Pane Terminal. Block The SCB-100A is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with shielded cables, the SCB-100A provides rugged and protected signal connectivity. It has a mechanical enclosure that features a magnetic removable lid and pinout diagrams. It also includes pane, wall, and DIN Rail mount options.
