Product

MIMO Antenna Assembly for Shield Box

HDRF-MIMOST2570

-

RF Electronics

HDRF-MIMOST2570 - RF Electronics

MIMO Antenna setup assembly customized for HDRF-series shield boxes

Product

VXI Rev 4.0 Module Shield Kits

-

ICS Electronics

ICS Electronics

*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.

Product

Hall Effect Measurement system

HMS-3000

-

ECOPIA

HMS-3000 - ECOPIA

Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.

Product

Aspirated Radiation Shield

-

Apogee Instruments, Inc.

Apogee Instruments, Inc.

The fan has an ingress protection (IP) rating of 55, virtually eliminating moisture and dust ingress. At full speed the power requirement is 1 W (80 mA at 12 V DC). To conserve power fan speed can be reduced, via pulse width modulation (PWM), to 0.3 W at night or when wind speed is greater than 3 m s-1 without loss of accuracy. If the fan is continuously operated at full speed lifetime is rated at 50,000 hours (5.7 years). The fan includes a tachometer, allowing RPM to be mounted to detect obstruction of the fan.

Product

RF Shield Box

-

Qosmotec Software Solutions GmbH

Qosmotec Software Solutions GmbH

Qosmotec RF Guard is a RF shield box that allows engineers to create an affordable automated end-to-end test environment with each UE shielded individually. It enables the user to perform wireless network tests without undesired RF interference by protecting mobile devices from outside network frequencies.

Product

RF Shielded Enclosure, 80dB Isolation Testing

QuietBox-80c/r

-

Raymond RF Measurements Corp.

QuietBox-80c/r - Raymond RF Measurements Corp.

The Raymond RF QuietBox-80c/r line of all-aluminum tabletop and rack mountable RF Shielded Cabinets offers effective RF isolation in a lightweight, fully-customizable package. Each QuietBox 80c/r is designed from the ground up to satisfy all the requirements of the client including enclosure dimensions, door swing and mounting style (tabletop or rack mount).

Product

RF Shield Box

Immunity

-

Laplace Instruments Ltd.

Immunity - Laplace Instruments Ltd.

A small versatile manual shielding box that is designed for small scale device testing such as wireless network cards and wireless communication equipment.

Product

Shielding Solutions

-

Aaronia AG

Aaronia AG

The highly transparent EMC shielding material Aaronia-Shield® and the high-tech EMC shielding fleece Aaronia X-Dream®, for example, offer very high EMC protection and are especially well equipped for all future high-frequency radiation sources in the high GHz range, which you can easily verify with our EMC Handheld Spectrum Analyzer. For magnetic field shielding, our MagnoShield® series offers unparalleled protection against alternating magnetic fields, such as cables, power distributors, high-voltage lines or transformers and generators.

Product

MAX31855 J-Type Thermocouple Arduino Shield

SEN-30004-J03

-

Playing With Fusion Inc

SEN-30004-J03 - Playing With Fusion Inc

Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega

Product

RF Shielded Test Enclosure, Low Profile

JRE 2214

-

JRE Test, LLC

JRE 2214 - JRE Test, LLC

Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. Tough 'honeycomb' vent maintains shielding effectiveness throughout the full frequency range. Optional fan is available for additional airflow.

Product

Dual RF Shielded Test Enclosure

JRE 0814-2R

-

JRE Test, LLC

JRE 0814-2R - JRE Test, LLC

Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R is ideal for testing devices with a tall form factor. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.

Product

RF Shielded Test Enclosure

JRE 0814

-

JRE Test, LLC

JRE 0814 - JRE Test, LLC

Testing tall devices? The 0814 stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure finds wide use in the WiFi test environment. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.

Product

Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces

-

Sifos Technologies, Inc.

Sifos Technologies, Inc.

Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions.  Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.