Product

Heavy Duty Digital Multimeter

DMM 8007

-

Tecpel Co., Ltd.

DMM 8007 - Tecpel Co., Ltd.

1.999 count LCD display. Resistance to 2000 M£[. Frequency to 20MHz. Capacitance measurement. Inductance measurement. Logic Test. Transistor hFE test. Audible continuity test 

Product

PAT and Installation Verification Unit

PowerCheck 1557

-

Seaward Electronic Ltd

PowerCheck 1557 - Seaward Electronic Ltd

The PowerCheck 1557 is a comprehensive PAT and installation verification checkbox. It carries out ongoing performance checks to ensure accurate measurement between calibration intervals. Fully tests Earth Continuity, Insulation Resistance, RCD Trip Time, RCD Trip Current, Loop, PE Conductor Current, Touch Current and Flash tests.

Product

Thermitest

THW-L2

-

Thermtest Instruments

THW-L2 - Thermtest Instruments

Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.

Product

Ultra sensitive heat flux plate

HFP03

-

Hukseflux Thermal Sensors B.V.

HFP03 - Hukseflux Thermal Sensors B.V.

HFP03 is an ultra sensitive sensor for heatflux measurement of small heat fluxes through soil, walls and building envelopes. By using a ceramics-plastic composite body the total thermal resistance is kept small.

Product

Electric Shock Protection Analysis

-

ETAP

ETAP

60364-4-41 StandardBS 7671 StandardEN 50122 StandardTN-C, TN-S, TN-C-S, TT & IT Earthing TypesElectric shock requirementsLoop impedance and current calculationTouch voltage calculation and evaluationCalculation considers resistance to ground / earthGround Fault Current Interrupter (GFCI) or Residual Current Circuit Breaker (RCCB) or Residual Current Detector (RCD) protectionReports in Crystal Reports and MS Excel

Product

Piezo-resistive Accelerometer

-

IMV Corporation

IMV Corporation

A Piezo-resistive Accelerometer has a stable structure composed on a silicon chip created by the micromachining and semiconductor production technology. A mass and a beam on which a set of the Piezo-resisters are created on the silicon chip. A set of electrical bridged is formed by such Piezo-resistive resisters to generate signals proportional to the applied acceleration.

Product

Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit

72-7770 CAL DU

-

Tenma

72-7770 CAL DU - Tenma

The 72-7770 CAL DU from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.

Product

Femto / Picoammeter And Electrometer Meters

B2980 Series

-

Keysight Technologies

B2980 Series - Keysight Technologies

The Keysight Femto / Picoammeters and Electrometers / High Resistance Meters offer best-in-class measurement performance and unprecedented features to maximize your measurement confidence. The Femto / Picoammeters and Electrometers both offer 0.01 fA (0.01 x 10-15 A) minimum current resolution, which meets virtually all existing and future low-level current measurement needs. The Electrometers feature a 1,000 V voltage sourcing capability that supports up to 10 PΩ (10 x 1015 Ω) resistance measurements. Both of the Femto / Picoammeter and Electrometer have battery powered versions to eliminate AC power line noise, providing unmatched level of noise reduction, enabling low-level measurements that were previously impossible.

Product

Handheld Water Quality Meters

LAQUA DO220

-

HORIBA, Ltd.

LAQUA DO220 - HORIBA, Ltd.

Measures dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation0.01 mg/L or 0.1% DO resolutionCompensates salinity, temperature, and atmospheric pressure Allows up to 2 calibration points using galvanic DO electrode°C & °F temperature readingsWith real-time clock and date/time stamp for GLP complianceAuto log data; built-in memory can store up to 1000 dataAuto stable, auto hold, and real-time measurement modesAuto shut-off (programmable: up to 30 minutes)Built-in electrode holder allows 2 electrodes to be attached Monochrome LCD with white LED backlight: 50 x 50 mmPhono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slipPowered by 2 x AA batteriesPackaged with galvanic electrode in carrying case3 years meter warranty

Product

Industrial Gas Detector

OLCT 60

-

Teledyne Gas & Flame Detection

OLCT 60 - Teledyne Gas & Flame Detection

The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.

Product

Surface Carbon Analyzer

SurfaceC‑800

-

ELTRA GmbH

SurfaceC‑800 - ELTRA GmbH

Determination of surface carbon is a special requirement for quality control in the metal producing and metal working industry. ELTRA’s SurfaceC-800 analyzer is designed for the precise determination of surface carbon in numerous kinds of solid samples from trace level up to 1000 µg/cm2. The SurfaceC-800 is equipped with a resistance furnace with quartz tube for sample oxidation and can provide temperatures up to 1000 °C. The temperature of the SurfaceC-800 can be set up in steps of 1 °C. As common carrier gas in the SurfaceC-800 oxygen is used.

Product

Cathodic Protection Digital Voltmeter

CPV-4

-

Tinker & Rasor

CPV-4 - Tinker & Rasor

The CPV-4 is a DC digital voltmeter with a input resistance of 20 meg ohm and two voltage ranges

Product

Martindale Abrasion Tester

UI-FT19

-

Unuo Instruments

UI-FT19 - Unuo Instruments

Martindale Abrasion Tester is used to test pilling & abrasion resistance of textile fabric, leather and other materials by rub sample in all directions (a Lissajous figure) in wet or dry conditions.

Product

Armature Tester

-

Qingdao AIP Intelligent Instruments Co., Ltd

Qingdao AIP Intelligent Instruments Co., Ltd

This tester is suitable for online or offline detection of various armature electrical properties, such as power tool motors, garden tools, vacuum cleaner motors, small household appliance motors, automobile motors, fitness equipment motors, permanent magnet micro-motors, etc. The tooling of the tester meets the requirements of arbitrary placement of the armature, and can automatically and accurately sort/track faulty solder joints; the equipment startup methods include buttons, remote control, and sliding cover; it meets the armature test of special processes such as double insulation, and automatically identifies solder joints, winding short circuit/open circuit , winding errors, poor welding and other problems; the tester can also automatically count the number of tests, the number of defectives and other data, which is convenient for quality management analysis.The tester test items mainly include:bar-to-bar resistance, diagonal resistance, welding resistance, insulation resistance, ac hi-pot, surge.

Product

POWER PROBE 4

PP401

-

Matco Tools

PP401 - Matco Tools

*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)