Response
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm With SPDT
50-293-112
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Impedance Analyser Frequency Response Analyser
C60
-
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
Product
- RS-422 and RS-485 Lightning/Surge Protector
Model 22NX
-
FEATURES: Triple Stage Protection; Fast Response Time For RS-422 / RS-485; Prevents Damage to Modems, Converters, and Terminals; Accommodates Data Rates to 10 MBPS; Supports 4 Circuits. The Model 22NX Lightning Sponge is designed to accommodate high-voltage transients, slow them down and redirect them to a low impedance path to earth ground.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Ocean and River Instruments
RINKO EC (ARO-EC)
-
Aquatic eddy covariance method is a powerful technique to measure benthic fluxes. The robust RINKO EC (model name: ARO-EC), as a new member of the RINKO series, is designed for aquatic eddy covariance measurements. The RINKO series is based on the optical (phosphorescence) principle which is now widely known as a remarkably fast response oxygen sensor with high accuracy. The response time of the RINKO EC oxygen sensing foil is less than 0.5 s (90%, from air to water at 25 °C). The foil life-time is more than 200 h, which enables at least 1 week of continuous measurements of dissolved oxygen. Moreover, the foil can be replaced easily by the user. Berg et al. (2016)*, after a detailed evaluation, concluded that RINKO EC is a reliable alternative for aquatic eddy covariance measurements of oxygen fluxes and its high data quality allows for new opportunities for eddy covariance flux studies, including long-term deployments in rivers, streams, and marine environments.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
*OEM Power Sensors
-
The OEM “standard” sensors are actually families of existing OEM sensors with typical specifications shown. They can be tailored as needed to fit your specific requirements. In addition to the products described, Ophir has developed hundreds of other OEM solutions. These compact laser power sensors have built-in amplifiers and are easy to install. They contain all the electronics needed including algorithms to increase the sensor's speed of response. Connections to the sensors are simple, with the host providing DC power and the sensor providing a voltage or digital output. Outputs Available: DB15 smart sensor output; Calibrated analog output; RS232; USB; Ehthernet. Simply fill out the Sensor Customization form so we can provide just the right solution for your needs.
-
Product
UV Photodiodes
-
Active area from 0.06 mm² to 36 mm² and quadrant photodiodes for position detections. Spectral response for broadband UV or filtered for UVA, UVB, UVC or UV-Index. Various entrance optics and housings options available (TO or SMD). Our own SiC photodiode chip production since 2009 also available with VUV sensitivity. PTB (German equivalent of NIST or NPL) measured high radiation hardness. 350°C high temperature stable photodiodes available. Photodiode application guide.
-
Product
Laser Doppler Surface Velocity Meter
LV-7000 series
-
The LV-7000 series detects speed, uneven speed, distance, length of moving object or rotating object without contact. By contacting with 2 sensors, it enables to calculate difference in velocity/length between the two points in real time and output with 3,000 ppm of accuracy. The frequency response can be expanded up to 20 kHz, which achieves to understand phenomena and evaluate mechanical systems at high speed, efficiently, and accurately. It is useful for evaluation of motor control and behavior measurement, improving parts quality, and reducing loss of material.
-
Product
Smart Inspection Station
SiS
-
Smart Inspection Systems LLC was born in 2010 in response to orthopedic manufacturers’ demands for faster inspection than their sister industries. Our signature product, the Smart Inspection Station™ (SiS™), is an automated turnkey inspection solution that yields comprehensive visual reports with complete geometric form and dimensional pass/fail in just minutes. The SiS™ is custom-configured per the client’s needs, yet versatile enough for simultaneous commissioning on multiple product lines. The product of years of refinement, the SiS™ gives comprehensive visual reports with complete geometric form and dimensional pass/fail in just minutes. Your SiS™ can be custom-configured according to your needs, but is still versatile enough for simultaneous use on multiple product lines. And best of all, every SiS™ purchase comes with ongoing support from L3I’s expert staff.
-
Product
Phase Angle Meter
-
Exceptionally fast response (up to 20 updates per second) and high accuracy for low frequencies, such as AC line frequency. A resolution of 1, 0.1 or 0.01 is user-selectable. Accuracy is 0.01% up to 100 Hz, 0.1% at 1 kHz, and 1% at 10 kHz.
-
Product
Single Channel Instrument for General Acoustic / Vibration Measurements
SVAN 979
-
SVAN 979 is the most advanced and powerful single channel instrument for general acoustic and vibration measurements ever made. The list of the instrument outstanding features and functionalities includes:- high accuracy sound and vibration measurements- most powerful frequency analysis package- time-domain (WAV) and Audio Events recording to Micro SD card- very high dynamic measurement range- extremely flat frequency response (digitally compensated)- extremely flexible set of interfaces (USB, Bluetooth, IrDA, RS232 and more)- USB Host port providing very flexible functional extensions capabilities- firmware ready for GPRS and WLAN communication (USB Host port)- GPS time synchronisation
-
Product
Power Rail Probe, 6 GHz
N7024A
Oscilloscope Probe
The N7024A power rail probe is for users making power integrity measurements that need mV sensitivity when measuring noise, ripple and transients on their DC power rails. The probe is designed for measuring periodic and random disturbances (PARD), static and dynamic load response, programmable power rail response, and similar power integrity measurements. Many of today’s products have tighter tolerances on their DC power rails than the previous generations of these products, and the N7024A power rail probe is designed to help users ensure their products meet these tighter tolerances.
-
Product
ELT STALKER Vector-finder
VF-121
-
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
Product
Photocouplers/Optocouplers IC Output
-
The PS8xxx/PS9xxx series, a range of IC output type photocouplers (optocouplers), feature a high-speed response from 1Mbps to 15Mbps and a wide variety of DIP and SOP packages that can be surface mounted (SMD).
-
Product
Squeak & Rattle Sub-System And Component Testing
-
At MB Dynamics, we’re proud to provide clients in a wide range of industries with quiet, custom turnkey component testing systems for combined squeak & rattle testing as well as durability testing of different components and subsystems (in 1 to 6 DOF). Test items can be excited in one or more axes to understand and characterize the physics and root causes of BSRs. Real-world, on-road vibration conditions are multi-axis simultaneous – vertical, fore-aft or longitudinal, lateral, roll, pitch, and yaw – 6 degrees of freedom or 6 DOF. Affordability drives decisions to find BSRs by exciting in one or two – fewer than 6 DOF. That has been a driving force for MB – be effective at finding BSRs with a lesser number of shakers (DOFs) and thus reduce the test equipment cost of finding BSRs. Vertical-only can be effective; sequential vertical then fore-aft then lateral is one step closer to real-world; creating vibration in four or five axes of response simultaneously is even closer; and full 6 DOF systems that are quiet come closest to duplicating in the lab the on-road conditions. MB offers all these possibilities to meet trade-offs of budget, test time, road replication, and BSR detection effectiveness.
-
Product
Performance Testing
-
We do performance testing of applications across domains and technologies, including web-based n-tier applications, client-server applications, SOA based solutions or COTS solutions. We have experience with all industry-leading performance testing and monitoring tools, along with expertise in end-to-end application performance including network, database, hardware, etc. We publish a detailed performance testing report for the application with response times, break-point, peak load, memory leaks, resource utilization, uptime, etc. We provide clear and actionable application tuning recommendations and help you implement those working closely with various IT teams in your enterprise.
-
Product
S2 Spectra USB Sensors
ULP S2 SPECTRA USB
LED Sensor
Universal LightProbe S2 Spectra USB Sensors test a wide range of LED intensities and any color in the visual spectrum, plus white, providing a linear response with a serial digital output via a PC. A standard USB Cable is provided to connect to a mini-type B five-pin USB connector, which is integrated into the S2 Spectra USB Sensor.Operating temperature range: 0oC to 70oCOutput Port: A standard mini-type B five-pin USB connector is integrated into the S2 Spectra USB Sensor,and a standard USB Cable is provided to connect to a USB portSensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: < 10mS for color and intensity as a serial bit- stream (19200 baud rate)Fiber-Optic Probes: Can be paired with any of a wide range Universal LightProbe Fiber-Optic Probes
-
Product
Smart Analog IC101
-
Flexibly change analog front end (AFE) settings in response to environmental changes
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
Photoelectric Sensors / Laser Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers some of the smallest Photoelectric Sensors in the world and include sensors with or without a built-in amplifier. With advanced features such as background/foreground suppression to protect against unwanted detection and the choice of built-in amplifiers that provide the same high-speed response and built-in features that can be found in high-end Fiber Optic Amplifiers, Panasonic can ensure the highest quality sensing available to meet any application requirement.
-
Product
Energy Probes
RjP-600 Series
-
The RjP-600 Series energy probes integrate the detector and preamplifier in the same enclosure, thereby maximizing signal integrity between the detector and preamplifier. This permits longer cable runs between the probe and instrument, as is often necessary in production environments. Probe specific information, like calibration date and wavelength response curves, is stored in the probe for access by the instrument. Other features include interchangeable filter holders and ¼-20 mounting hole.
-
Product
Compact Single-Point Anemometer
ComfortSense Mini
-
The ComfortSense Mini is a compact and robust single point anemometer that covers a wide range of applications. With an easy exchange of probes, the ComfortSense Mini covers both high velocity measurements in ventilation ducts as well as draught measurements in offices. The velocity probes are based on the well-proven technology of thermal anemometry which offers a wide velocity range, increasing sensitivity as velocity decreases, and fast response. This makes it particularly suitable for very low velocities, at which other methods either fail or become too inaccurate.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Coaxial Power Detector
-
RF Lambda’s coaxial power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
InfiniiMax Probe, 5 GHz
1132B
Oscilloscope Probe
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
Product
SGR Scintillation Gamma Radiameter
-
SGR scintillation gamma radiameter serves for fast and sensitive indication of gamma-ray sources. SGR covers two basic ranges of measurements:quick and selective searching for radioactive sources with fast response, acoustic signalization and histogram of 64 measured values radiometric measurements (dose rate) with the support of point and continuous measurements.
-
Product
Scanning Probe Microscopy/Atomic Force Microscopy (SPM/AFM Analysis)
-
Rocky Mountain Laboratories, Inc.
Scanning probe microscopy (SPM) refers to a family of measurement techniques that utilize a scanning probe. The most common measurement is Atomic Force Microscopy (AFM Analysis), which measures surface topography. Imaged areas can be from the nm scale to as large as 100 µm X 100 µm. Heights and depths of features can be measuredand many surface roughness parameters, e.g Ra, can be calculated. 3-D images can also be produced for dramatic data presentation. Magnetic and electrical response can also be measured with SPM.
-
Product
High Resolution Frequency Response Analysis (FRA) System
TR-AS FRA
-
The Frequency Response Analysis (FRA) on power transformers is used for diagnosis at works, after putting into operation and for maintenance on site. The frequency dependent admittance is determined and recorded as fingerprint.
