PCI Test
-
Product
PCI 24-Bit Digital I/O Cards
PCI-DIO-24D/H
-
These cards are 24-bit parallel, digital input/output cards designed for use in PCI-Bus computers. The difference between the models is that I/O connections to PCI-DIO24D are via a standard 37-pin D-sub connector while I/O connections to PCI-DIO24H are via a 50-pin connector. The cards are 4.80 inches long (122 mm) and may be installed in any 5V PCI-bus slot in IBM and compatible personal computers.
-
Product
Arbitrary Waveform Generator PCI Card
GC1300
Waveform Generator
The GC1300 is a single-channel PCI-based Arbitrary Waveform Generator. It is a high performance waveform generator that combines many powerful functions in one small package. Supplied free with the instrument is Arbconnection software, which is used for controlling the GC1300 and for generating, editing and downloading waveforms from a remote computer.
-
Product
PCI Daughter Boards
DB-24POR/D (with D-Sub cable)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
Color Tests
LED-Check
-
LEDs are the standard light source in car cockpits. It is not sufficient to find out if a LED shines, or not. The LED needs to have precisely the specified brightness and color to fulfil its function.The FiberVision LED-Check system tests up to 250 LEDs in less than one second.
-
Product
PCI To PC104 Extender Board
MS 1717
-
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
Product
Test Sets For Diagnostic Testing
-
Test Sets For Diagnostic Testing are designed to test Oil Resistivity, Tan Delta, High Voltage Surge Comparison, etc. These test sets are automated instruments used to measure electrical features to insulate transformer oil, liquids and varied other insulating materials. They are ideal for revealing different localized problems and varied weak spots in the insulation. These modern testing sets are designed to provide high accuracy in results. In addition to this, they are easy to maintain testing sets available to ensure accurate readings.
-
Product
PCI 2 Amp Multiplexer, Single 64-Channel, 1-Pole
50-635A-001
Multiplexer Module
The 50-635A-001 is a single 64-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Localization Testing
-
Localization testing is a method that ensures that an application can be used in a specific area or region. It involves testing the application to verify the accuracy, behavior, and suitability in a specific geographical area.
-
-
Product
FCC Testing & Certification
-
F2 Labs can provide you with Federal Communications Commission (FCC) Certification in our EMC Testing Lab, Supplier’s Declaration of Conformity (SDoC), formerly Verification and Declaration of Conformity, testing. Manufacturers who sell electrical and/or digital products in the United States must have their products tested by an accredited lab certified by the FCC. F2 Labs is accredited by the FCC as a Conformity Assessment Body (CAB). We partner with a Telecommunication Certification Body (TCB) in order to provide our clients with FCC Part 15 certification and compliance testing & approvals.
-
Product
ARINC PCI Express One Lane Interface Card
PCIE1L-A429
Interface Card
The ARINC PCIE1L-A429 Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture. The one lane card PCIe is the industry first low profile
-
Product
Avionics Test
-
VIAVI Solutions offers a wide range of avionics test solutions supporting engineering, factory, flightline, and return to service test requirements. Working closely with avionic OEM’s and users, we strive to develop a comprehensive and user friendly solution utilizing modern technology to meet the long term needs of the aviation industry.
-
Product
Magnet Testing
Helmholtz Coils
-
A coil arrangement consisting of two coils with the same radius or edge length is called a Helmholtz coil. At the correct distance, these coils are arranged in parallel on the same axis and current flows through them in the same direction. Their magnetic field is then characterized by a large homogeneous area in the center of the coil, which is freely accessible for experiments and measurement tasks. Helmholtz coils can have a circular or square geometric shape.
-
Product
Software for Testing Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
We offer extensive and powerful software packages for our systems. All of our testing systems are controlled with our Hillgus testing software and the test results are stored in our open file formats. With our evaluation software Oculus, the findings can be subsequently evaluated and documented. Both Hillgus and Oculus were developed in-house and are constantly being improved. Due to the modular structure, the software can be optimized for every requirement and expanded at any time.
-
Product
20-Port PCI Express
PEX 8680
-
The ExpressLane™ PEX 8680 device is the industry's first PCIe switch to offer 80 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 20 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 80-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
-
Product
Hardness Testing Devices
-
Institut Dr. Foerster GmbH & Co. KG
NewSonic’s hardness testing devices test hardness in a nondestructive way using the UCI method (ultrasonic contact impedance). The testing procedure enables quick and mobile measurements (1-second type) to supplement traditional hardness testing. The devices feature compact measurement probes which can also be used in difficult testing positions and component geometries. The areas of application include incoming goods inspection, mix-up checks, production controls, quality assurance, weld seam inspection, cut edge checks, maintenance of built-in components, as well as the replacement of dynamic hardness testing devices in the case of thin materials (below 50mm, e.g. boilers, pipes)
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 925Ω
50-297-121
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Testing Instruments
-
NDT testing instruments, other testing instruments, paper testing instruments, plastic testing instruments, rubber testing instruments, soil testing instruments
-
Product
Test Automation Framework
TEAF
-
Testing frameworks are an essential part of any successful automated testing process. They can reduce maintenance costs and testing efforts and will provide a higher return on investment (ROI) for QA teams looking to optimize their agile processes.
-
Product
PCI Express Digital I/O Boards
PEX-P8POR8i
-
PCI Express x1, 8-channel isolated digital input.8-channel PhotoMos Relay output. Includes one CA-4002 D-Sub connector.
-
Product
Test Contactor/Probe Head
Mercury
-
Mercury™ test probes and contactors are excellent spring probes for the laboratory though they were designed with the robust qualities needed for high-volume production test. Their unique design ensures excellent plating quality for low, consistent resistance, long life, and high-test yields.Mercury probes are available with minimum pitches of 0.3 mm, 0.4 mm, 0.5 mm, and 0.8 mm, to provide the best performance at any device pitch. Mercury probes have bandwidths of up to 22 GHz, and can carry over 3 Amps of current. The Mercury is an excellent choice for any test application.
-
Product
PCI Express System Timer (USB Interface)
SKU-032-01
-
The MiniPCI Express System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
Product
Relay Test Equipment
ME3000 Series
-
ME3000 is recently developed low-cost oriented relay test equipment, aimed to supply customer cheaper and cost-effective product.
-
Product
PCI Three-Axis Laser Board
N1231A
Laser Board
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
Test Automation Services
-
One of the effective approaches we are constantly using is keyword-driven testing (KDT). This approach covers hundreds of test cases in long-term projects with complex business logic.
-
Product
Haptic Testing System
-
The Air Ventilator Haptic Test System performs automatic functional tests on air ventilation components to measure the force necessary for the execution of movements in the different components of the part. The movements are performed by a 6-axis robot that forces the components of the part to follow the desired routes while storing data on the force expended. This particular machine tests movable fins and knurled wheels by performing four test motions on each fin and two on each wheel.
-
Product
Transformer Testing Equipment
-
Offering you a complete choice of products which include Automatic Transformer Turns Ratio Instruments (ATRI- 3), Automatic Transformer Turns Ratio Instrument (ATRI-201), VTRI-2000 ( Transformer turns ratio instrument ), Current Transformer Test Set (CTC-1), Potential Transformer Tester ( PT Tester ) and Current Transformer Tester ( CT Tester ).
-
Product
TWT Test Set
-
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process. Polarity designed and developed this Microwave Tube Test Set with the following specifications:
-
Product
Connector Test
-
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
Product
Optical Loss Testing
-
Is to inject a known level of light in one end and measure the level of light at the other end, using an OLTS. The difference between source and receive power levels is the loss.
