PCI Test
-
Product
ZIF PCI Test Connector
-
Meritec's ZIF PCI Test Connector offers the user an accurate and reliable way in which to test their PCI cards. With over 20,000 reliable cycles, it eliminates the need to constantly replace your PCI Connectors. Meritec's Test Connector assembly plugs directly into the PCI Connector in the test bed and is actuated by a lever for easy loading and unloading of cards. Meritec's solution eliminates the uncertainty associated with intermitancy between the PC Board and Test Connector during the test cycle.
-
Product
32-bit PCI Test Backplane
SKU-014-01
-
The 32-bit PCI Test Backplane was designed to support production testing/debugging of PCI-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into four 32-bit PCI slots via 7 ft CAT6 cable. The PCI backplane is a versatile platform that allows you to test up to 4 PCI boards at the same time, facilitates easy access to logic signals, provides hot-swap compatibility, and per-slot overcurrent protection.
-
Product
PCI Express® Electrical Performance Validation and Compliance Software
D9040PCIC
-
D9040PCIC PCI Express Transmitter Test Compliance Software for PCI Express 4.0 (PCIe 3.x, 2.x and 1.x also supported).
-
Product
PCI Express Gen 1 Test Backplane
SKU-015-01
-
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
Product
PCI Express, PCI, Multi-Interface Test Backplanes
-
Amfeltec PCI Express, PCI, Multi-Interface Test Backplanes
-
Product
PCI Express 4.0 Test Platform
Test Platform
The PCI Express 4.0 Test Platform provides a convenient means for testing PCIe 4.0 add-in cards with an internal interposer and power supplies. The Summit Z416 Test Platform provides the platform for the Summit Z416 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen4, Gen3, Gen2 or Gen1 hosts and devices. It supports SMBus and other sideband signals.
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
Product
Socket Saver
4690
-
The Technobox PMC Socket-Saver permits cost effective volume testing of PMC modules when used with Technobox P/N 3390 ?PMC to PCI adapter for Test.? It may also be used to reduce wear and tear on Technobox P/N 1518/1523 (?Extender/Preprocessor?).
-
Product
PCIe 3.0 and 4.0 Compliance Testing
-
Teledyne LeCroy offers an integrated and automated compliance testing system, approved by the PCI-SIG as a standard tool for Link and Transaction Layer Compliance testing for developers working with the PCIe 3.0 and PCIe 4.0 specification. This solution combines a Summit Z416 Exerciser and a PCI Express Test Platform (for testing End-Point devices) This system has been selected by the PCI-SIG as a standard test tool for PCI Express 3.0 and PCI Express 4.0 Link and Transaction Layer Compliance Testing.
-
Product
PCI Express PLL Test Application
N1081PLCA
-
Keysight N1081PLCA PCI Express PLL Test Application designed to measure transmitter PLL bandwidth and peaking based on the PCI Express 5.0 TX PLL Specifications. Use N1081PLCA PCIe PLL test software to test, debug and characterize your PCIe designs.
-
Product
PCIe Compliance Testing
-
Teledyne LeCroy offers an integrated and automated compliance testing system, approved by the PCI-SIG as a standard tool for Link and Transaction Layer Compliance testing for developers working with the PCIe 4.0 and PCIe 5.0 specification. This solution combines a Summit Z58 or Summit Z516 Exerciser and a PCI Express Test Platform (for testing End-Point devices) This system has been selected by the PCI-SIG as a standard test tool for PCI Express 4.0 and PCI Express 5.0 Link and Transaction Layer Compliance Testing.
-
Product
PCI Express 5.0 Test Platform
Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
Product
250 KS/s, 16-Bit, 8-Ch Simultaneous Sampling, Multifunction PCI Card
PCI-1706U
PCI Card
8 differential analog inputs8 A/D converters simultaneously sampling16-bit A/D converter, with up to 250kHz sampling rate for each channelProgrammable gainMultiple A/D triggering modesOnboard FIFO memory up to 8K SampleProgrammable pacer/counterBoardID™ switchUniversal PCI Bus (supports 3.3V or 5V PCI bus signals)
-
Product
Full DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285
PCI Card
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer (10K points) for trajectory planning which is designed in DSPSupports E-Gear, and helical interpolationSupports E-CAM providing 256 points to describe the CAM profiles which buffers located in DSPHardware emergency inputWatchdog timerPosition latchPosition compare triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPProgrammable interruptSupports gantry mode by semi-closed loop pulse train controlRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.
-
Product
1 MS/s, 12-Bit, 16-Ch Multifunction PCI Card
PCI-1712
PCI Card
16 single-ended or 8 differential or a combination of analog inputs12-bit A/D converter, with up to 1 MHz sampling rateTwo 12-bit analog output channels with continuous waveform output function16-ch digital input and 16-ch digital outputThree 16-bit programmable multifunction counter/timers on 10 MHzProgrammable gainAutomatic channel/gain scanningOnboard FIFO memory (AI: 1,024 samples AO: 32,768 samples)Auto-calibration (AI/AO)PCI-Bus for data transferPre-, post-, about- and delay-trigger data acquisition modes for analog input channelsFlexible triggering and clocking capabilities
-
Product
Full DSP-Based 4-Axis Motion Control Universal PCI Card
PCI-1245
PCI Card
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer (10K points) for trajectory planning which is designed in DSPSupports E-Gear, and helical interpolationSupports E-CAM providing 256 points to describe the CAM profiles which buffers located in DSPHardware emergency inputWatchdog timerPosition latch via ORG & index signalPosition compare triggering up to 100 KHz, and memory buffer is up to 100K points in DSPProgrammable interruptSupports gantry mode by semi-closed loop pulse train controlRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
ARINC429 PCI Express Mini Card
AMEE429-x
PCI Express Mini Card
The AMEE429-x is AIM’s new PCI Express Mini Card module targeted for embedded ARINC429 applications in an ultra-compact form factor.
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
250kS/s, 16-Bit, 16-Ch Multi-Function PCI Card
PCI-1716
PCI Card
16 single-ended or 8 differential or a combination of analog inputs16-bit A/D converter, with up to 250 kHz sampling rateFIFO memory (8,192 samples)2 analog output channels16-ch digital input and 16-ch digital outputAuto-calibrationBoardID™ switch
-
Product
In-Circuit Test
TestStation LH
Test System
The TestStation LH in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne's popular, award winning TestStation product family.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
SoC Test Systems
Test System
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
Product
Single Site Test Handler
3210
Test Handler
Chroma Single Site Test Handler 3210 supports various package types such as BGA series, QFP series, QFN, TSOP, and more. The handler is primarily designed for early device design and engineering validation.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
ESS Performance Test System
Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Die Test Handler
3112
Test Handler
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
EBIRST 200-pin LFH To 104-pin D-type Adapter
93-002-422
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
