Optic
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Optics Height Adjuster and Post
10785A
Accessory Kit
The Keysight 10785A Height Adjuster and Post is used to precisely position optics devices associated with the 5530 Laser Calibration System, such as the 10766A Linear Interferometer. The height adjuster and post also facilitate adjustments in measurements such as pitch and yaw.
-
Product
Automated Fibre Loss Test Set
LTS-1500
-
The LTS-1500 is a small, rugged automated fiber optic loss test set that characterises singlemode fiber links at wavelengths of 1310, 1490 and 1550 nm. It is comprised of a sensitive InGaAs based optical power meter calibrated at six wavelengths with better than -75 dBm noise level plus a stabilised laser light source with up to three selectable wavelengths.
-
Product
Transmissive Rotary Codewheel
HUBDISK-1
-
US Digital offers a wide variety of standard hub / disk assemblies (optical encoder disks attached to an aluminum hub) to aid with mounting on a shaft. Encoder disks may also be ordered as a stand alone item (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable.
-
Product
Optical Tables with Broadband Damping
5100 Series
-
The 5100 Series features 3/16″ thick ferromagnetic stainless steel top and bottom skins, precision honeycomb construction, our patented SPILLPRUF spill management system, and broadband damping for excellent vibration absorption.Table lengths up to 20′Widths to 6′Thicknesses to 36″We love custom tables! Choose welded splice plates for extra long, wide, and “L”, “T”, or “U” shaped tables. Let us know your unique requirements and we will make it happen!All our optical tables may be paired with Active-Air or Passive-Air vibration isolators, or modular rigid supports, sold separately.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, LC Connectors
42-852A-418-M62.5
Multiplexer Module
The 40/42-852A-418-M62.5 is a PXI/PXIe 8-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
Relay
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
Standard Bare Fiber Spools
-
*Custom lengths to 30km of optical fiber*Designed to fit spools in the most efficient manner*Portable for easy handling and protection*Organizes fiber while ensuring performance
-
Product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
-
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
-
Product
Laboratory And Analysis Systems
-
High performance UV-VIS-IR spectrophotometer with superb optical performance for the determination of spectral absorption coefficient and spectral effective scattering coefficients
-
Product
Spectroradiometer
-
Konica Minolta Sensing Americas, Inc
To measure light radiation’s spectral characteristics, Instrument Systems optical spectroradiometers are the instruments of choice. Instrument Systems has a variety of optical spectroradiometers to meet any user’s needs or budget.
-
Product
Ultra High Speed Pick & Place
MC889
-
The MC889 is specially designed for the fast and highly precise loading of large batch sizes. This pick and place machine is equipped with an optical centering, "Vision on the Fly" system that guarantees the best possible measurement of SMD components (such as 0201, SOIC, PLCC, BGA, µBGA, CSP & QFP, as well as odd-shaped components) while completing placement at rates of 20,000 CPH.
-
Product
Module Type Amplifiers
-
Optical amplifier Gain Blocks are compact in size and suitable for built-in use. FiberLabs provides a wide wavelength range of optical amplifier Gain-Blocks over the O-, S-, C- and L-bands. These Gain Blocks can be used for B-PON system using three wavelengths of 1.31 μm, 1.49 μm, and 1.55 μm (ITU-T [compliant with G.983.3]), DWDM system and 100 GbE (IEEE 802.3ba) using the 1.3 μm band.
-
Product
Industrial IP69K Stainless Steel Panel PCs With 11th Gen Intel® Core™ Processor
Titan2
Panel PC
- 11th Gen Intel® Core™ i5/i3 BGA type processor- 15.6”/21.5”/23.8” FHD with projected capacitive touchscreen- Full IP69K rating for dust and water ingress- Corrosion-resistant 304 stainless steel enclosure (316 for Option)- All M12 type connectors suite for harsh environments- Optional for optical bonding and high brightness (1000 nits)- Standard VESA, Yoke/Pipe mount (optional)
-
Product
Spectrometer
LSCM
-
This device performs high-speed measurement and sorting of LED electrical and optical characteristics while synched with control signals from the LED production line inspection and sorting system. The LSCM then provides that pass/fail information to the system. The LSCM is equipped with the function to test both electrical and optical characteristics by applied voltage and current to the LED. This test device was designed to integrate test functions required by the inspection and sorting system into one compact body.
-
Product
Fluorescence Spectrophotometry
-
Agilent’s fluorescence systems, built by a global leader in fluorescence technology and molecular spectroscopy, are used by labs all over the world. The unique Xenon flash lamp technology in our Cary Eclipse Spectrophotometer delivers superior flexibility and sensitivity, and is ideally suited for use with fiber optic technology and bio-sample analysis. The Cary Eclipse is a high-performance workhorse for your analytical needs, providing robust, consistent results in every application.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, SC/PC Connectors
42-852A-218-M50
Multiplexer Module
The 40/42-852A-218-M50 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
32Ch Isolated Input Card
SET-1310
-
This card provides 32 optically isolated digital inputs. SET-1310 combines high-density IO with high isolation voltages and a wide input voltage range. It allows to break ground loops and protect your system from high-voltage spikes, but also to connect high voltage signals to standard logic level acquisition devices. The channel-to-channel isolation allows to connect signals from different DUTs to a single acquisition system without compromises.
-
Product
Power over Ethernet
PoE Tester
-
Covering both commercial and industrial applications, PLANET Power over Ethernet (PoE) products offer highly-dependable power and data transmission. Featuring 802.3bt standards, intuitive touch LCD design, Long Reach PoE technology over fiber optic cabling, coaxial cabling or UTP cabling, and PLANET exclusive intelligent PoE Management functions, all the requirements can be met for such applications as IP surveillance, IP communications, POS systems, PoE lighting and more. Our full range of PoE product lines include 95W 802.3bt PoE++/ 30W 802.3at PoE+ Managed Switches, Industrial flat-type PoE+ Switches, PoE Injectors, Splitters, Extenders designed for both indoor and outdoor environments.
-
-
Product
Single Fiber Aligner
1100
-
The 1100 Single Fiber Aligner uses patented fiber alignment concepts to produce virtually instantaneous temporary couplings for OTDR, dispersion, or any other optical fiber or component test that requires a fiber-to-fiber connection. It delivers low loss, low reflectance couplings on the first try virtually every time, without the need for test instrument feedback. As a result, temporary coupling times are minimized and manufacturing costs are reduced without compromising product quality.
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 10m
778959-10
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Fused Wavelength Division Multiplexer（1310/1550nm）
-
Flyin Optronics’ Singlemode wavelength division multiplexer WDM 1310/1550 1X2 2X2 combine or separate light at different wavelengths. They offer very low insertion loss, low polarization dependence, high isolation and excellent environmental stability. These components have been extensively used in CATV, WDM networks, Fiber sensor and fiber optics instrumentation.
-
Product
50-Watt Rack Mount Transmitter
FLS-2
-
Fiber optic cables are a critical part of modern life due to the vast amount of data they carry to support businesses, internet users, and emergency services. The cost of losing these services, even temporarily, is immeasurable. The FLS-2 system is designed to assist in locating, monitoring and providing damage prevention to these cables. The FLS-2 high-performance, high-power rack-mounted transmitter is typically mounted in a re-gen staton, customer access point, or central office. The FLS-2 transmits a locate tone on the metallic sheath of the fiber cable over vast distances to ensure the cable can be located quickly and accurately, even in congested areas.
-
Product
Motor Vehicle Headlight Testers
-
Foshan Analytical Instrument Co, Ltd.
It can be used to promptly and accurately measure the luminous intensity and the illuminating position(or the optical axis deviation amount) of the high/low beam of vehicle headlight. With the lamp image alignment techique the single-machine high/low beam testing needs only 30-odd seconds.It is also used for the dual-lamp test at the testing station,the dual-machine test at the same time needs only 20-odd seconds.
-
Product
Timing Board #2
TIO-10 #2
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. This board is similar to the Fiber Optic Interface to National Instruments TIO-10 Timing Board #1 only it has more channels connected to fiber optic transmitters and receivers.
-
Product
Backlight Module Optical Measurement System
-
RayClouds Photoelectric Technology Co.,Ltd.
The DM series backlight module optical characteristic automatic measurement system is equipped with photometer, colorimeter and spectroradiometer to measure the luminance and chrominance, uniformity of the backlight module.
-
Product
Quantum Laser Systems
-
By combining the Optical Frequency Comb and multiple ultrastable frequency stabilized lasers in a transportable, rack based system Menlo Systems offers a complete laser system for most demanding applications like optical clocks, quantum computing, and quantum physics experiments based on cold atoms, molecules and ions. The customer can configure the system in terms of laser wavelengths, laser power and frequency accuracy so that it is optimally matched to the application.
-
-
Product
UV-VIS Spectrometers
HummingBird
-
spectrometer is built with the linear CCD/COMS array sensor and 32bits RISC controller in. By simplification of the optical engine, the miniaturized spectrometer is achieved. It has three type of Light entrance, the user can choice Lens Tube, SMA905, or no entrance depends on needs. External MB type of HB Series can be chosen to enhance heat dissipation. The compact size and various of screw holes is very flexible for system integration.
