Servo
feedback seving to control.
-
product
Erichsen Metal Sheet Testing Machine for FLC, FLD
GBW-600
Jinan Testing Equipment IE Corporation
GBW series Erichsen Metal Sheet Testing Machine is designed on the basis of screw universal material testing machine, using the servo motor for highly accurate loading for punching, meanwhile, it is equipped with hydraulic servo control system for pre-tightening/clamping of metal sheet. It is ideal to evaluate the plastic deformation performance and ductility of metal sheet & strip materials. The cupping test for metal sheet thickness range is 0.1mm-5mm, Max. Punching capacity is 600KN, and the pre-tightening/clamping device is with hydraulic servo loading pump for 600kN capacity;
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Read-Write Analyzers
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
product
Synchro Control Transformer
SCT-RCT
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems.
-
product
Industrial Automation Components
Panasonic Industrial Devices Sales Company of America
Panasonic offers total automation solutions products that include PLCs, human machine interfaces, sensors, static control devices, laser markers, servo motors, temperature controllers, timers, hour-meters, counters, limit switches and other factory automation components.
-
product
Testing of Power Steering Motors
Endurance test bench on which up to five drives can be tested at the same time. The drives / DUTs are electrically connected to resistors and driven by a servo drive according to a predefined driving profile. This exam can take up to several days. It detects currents, speeds and temperatures.
-
product
Single-Axis Controller and Drive System
CDS-3310
Galil's CDS-3310 is a single-axis controller and drive system for precisely controlling a brush or brushless servo motor. It combines a high-performance, programmable motion controller with a 500W PWM drive in a compact, cost-effective package.
-
product
Electric Servo Motor Type 3-axis Vibration Tester
The Electric Servomotor Vibration Test System Is A New Vibration Test System Developed Based On The Control Technology Of AC Servomotors That We Have Cultivated Since Its Establishment.
-
product
Brakes
Power off, fail safe holding brakes. When voltage is applied, the friction disk is released allowing the motor shaft to rotate. Pittman power off brakes are best suited for parking brake applications used to hold a load in position, and are ideal for creating brake motor packages for small frame servo and stepper motors.
-
product
Motion Control Board, PCI
APCI-8001
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
product
Servo And VFD Filters
Operation of PWM-driven motors – servo motors and variable frequency drives (VFD) – causes several problems in equipment, including damage to the motor’s bearings due to leakage current causing electrical discharge machining (EDM) and damage to motor’s insulation. PWM motors also are a major source of EMI in equipment. These motor drive systems use pulsed power to drive the motors. As we are aware, the sharp edges of the pulses inevitably include high frequency components which can couple or radiate as noise to other parts of your system and cause unreliability, communication/control problems and EMC compliance issues.
-
product
Linear Amplifiers
LA Series
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
product
Motion Control Terminal Board for Yaskawa Sigma II Servo Amplifiers
DIN-814PA
This well-designed motion control terminal board is for the users who use Panasonic MINAS A super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
Synchro to BCD and Resolver to BCD Converters
TSBC TRBC
Computer Conversions Corporation
The TSB Series are miniature, high performance, continuous tracking, synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
product
Dual-Mode Charge Amplifiers
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Rack Mount Stage Controller
RM-2000
Applied Scientific Instrumentation
*2U 19" Rack Mount Control Unit: 22.8D x 48.3W x 8.1H cm (9" x 19" x 3.2").*100 MHz Microcontroller for Faster Command Processing and Servo Control.*Closed-Loop DC Servo Control of up to Four Motorized Axes.*0-10 Vdc DAC Output for Additional Analog Control.*Firmware Upgradeable via Serial Connection.*Remembers Last Position on Power Up.*LCD Display Shows Axes Coordinates and Status.*USB or RS-232 Serial Control with Rates to 115200 Baud.*"Zero", "@", and "Home" Buttons on Joystick.*Left- or Right-Hand Joystick Unit.
-
product
8/16-CH 16-Bit Analog Output Cards
PCI-6208/6216 Series
ADLINK PCI-6208/6216 series are 8 or 16-CH, 16-bit, analog output cards. The PCI-6208V-GL offers 8 voltage outputs with ±10 V range, featuring 15-bit monotonicity and 10 V/μs slew rate. The on-board analog switches minimize the power-on glitches. PCI-6216V expands the voltage output channels to a total of 16 for higher analog output density requirements. In addition to the voltage output functions, the PCI-6208A features 8 current outputs with ranges of 0-20 mA, 4-20 mA, and 5-25 mA. The daughter board EXP-8A provides high-quality voltage to current transducers. The PCI-6208A device is capable of delivering 14-bit monotonicity with 1.3 mA/μs slew rate. ADLINK PCI-6208 series devices provide high-resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
product
Linear Servo Motors And Drive Solutions
Linear drives and motors for high-speed and high-cycle operations, delivering unparalleled accuracy and performance benefits.
-
product
Advanced 4-Axis Servo & Stepper Motion Controller with Modular Design
PCIe-8154
The PCIe-8154 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8154 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8154 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
product
Passive Hydrogen Maser
VCH-1008
The VCH-1008 Passive Hydrogen Maser is a compact hydrogen maser with excellent frequency stability and utilises state-of-the-art technology. Full digital processing of the modulation and servo loop signals makes it ideal for high accuracy applications. An internal GPS/GLONASS option is available and provides automatic output signal frequency calibration.Key applications:- National Time Keeping Service- Space tracking and navigation- Verification of frequency signals - Scientific research
-
product
Synchro Differential Control Transmitter and Resolver Differential Control
SCDX-RCDX Series
Computer Conversions Corporation
The SCDX Series are low cost, miniature, solid state control differential transmitters and resolver transmitters designed for military and industrial control applications. They will directly replace electro-mechanical control differential transmitters (CDX) & thus provide digital control to existing analog servo systems.
-
product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
product
ISA Optima Motion Controllers, 1-8 axes
DMC-1700
The DMC-1700 for the ISA bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single ISA slot of a PC, the DMC-1700 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam.
-
product
Static Jack System
The servo actuator system applies static test force loads on structures at high precision to obtain their mechanical characteristics on an experimental basis.
-
product
EtherCAT Servo Drives And Motors
High-performance servo motor and driver systems designed for industrial automation applications.
-
product
PMAC Axes And Feedback Modules
PMAC's wide selection of axes and feedback modules are designed to work with most feedback devices and connect to different types of high precision servo drives.
-
product
Centralized Motion Controller
ADLINK‘s pulse train controllers provide comprehensive and application-oriented motion functions for servo and stepper motors through digital signal processing (DSP)-based and Application Specific Integrated Circuit (ASIC)-based two pulse train mode controllers to achieve excellent synchronous motion control and precise positioning suitable for laser engraving, marking and cutting applications in semiconductor, AOI, and conventional manufacturing industries.
-
product
Digital Display Auto Torsion Testing Machine
NJS Series
Jinan Testing Equipment IE Corporation
NJS Series Digital Display Auto Torsion tester is designed and built for torsion test on metal & non-metallic materials, as well as parts & components. NJS is loaded through the rotation of the active cartridge driven by the AC servo motor and cyclonical pinwheel reducer motor. The torque and torsion angle are measured respectively by the high-precision torque transducer and photoelectric encoder. The digital torsion testing machine is an essential instrument to inspect torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
