Servo
feedback seving to control.
-
Product
Single-Axis Controller and Drive System
CDS-3310
-
Galil's CDS-3310 is a single-axis controller and drive system for precisely controlling a brush or brushless servo motor. It combines a high-performance, programmable motion controller with a 500W PWM drive in a compact, cost-effective package.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
Laser Board
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
Structural Durability Products
-
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
Product
Multi-Axis Motion Controllers
DMC-40x0
-
The DMC-40x0 motion controller is Galil's highest performance, stand-alone motion controller. It belongs to Galil's latest generation motion controller family, which accepts encoder inputs up to 22 MHz, provides servo update rates as high as 32 kHz, and processes commands as fast as 40 microseconds-10 times the speed of prior generation controllers. The DMC-40x0 is a full-featured motion controller packaged with optional multi-axis drives in a compact, metal enclosure. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100Base-T or RS232. The controller includes optically isolated I/O, high-power outputs capable of driving brakes or relays, and analog inputs for interfacing to analog sensors. The DMC-40x0 controller and drive unit accepts power from a single 20-80 VDC source.
-
Product
8/16-CH 16-Bit Analog Output Cards
PCI-6208/6216 Series
Analog Output Module
ADLINK PCI-6208/6216 series are 8 or 16-CH, 16-bit, analog output cards. The PCI-6208V-GL offers 8 voltage outputs with ±10 V range, featuring 15-bit monotonicity and 10 V/μs slew rate. The on-board analog switches minimize the power-on glitches. PCI-6216V expands the voltage output channels to a total of 16 for higher analog output density requirements. In addition to the voltage output functions, the PCI-6208A features 8 current outputs with ranges of 0-20 mA, 4-20 mA, and 5-25 mA. The daughter board EXP-8A provides high-quality voltage to current transducers. The PCI-6208A device is capable of delivering 14-bit monotonicity with 1.3 mA/μs slew rate. ADLINK PCI-6208 series devices provide high-resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
STPOWER SLLIMM Intelligent Modules
-
Nowadays, the market requires high-performance solutions able to satisfy the increasing energy-saving requirements, compactness, reliability and system costs in home appliances and in low-/medium-power motor drive applications as well as in HVAC, servo motors and other high-power industrial drives.
-
Product
Servopulser Fatigue And Endurance Testing Machine
EHF-E Series
-
This is the standard electrohydraulic servo fatigue testing machine, offering outstanding stable performance. It is capable of carrying out tests ranging from static tests to fatigue tests.
-
Product
Inspection System
Pixie
-
3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Resolvers
-
Resolvers are electromechanical devices that convert mechanical motion into an electronic signal. Being analog devices, resolvers have no onboard electronics making them ideal for high shock, vibration and other harsh environments. Harowe offers frameless resolvers also known as servo resolvers or pancake resolvers consisting of a rotor assembly that is shaft mounted and a stator assembly that is mounted to the customer's device or housing as well as shafted housed resolvers with flange, servo groves and c-face mounts.
-
Product
CNC Vision Measuring Machines
SVM DCC Standard / Classic Series
-
*Professional and international origin brand name*Designed by professional development team, with style and structure in line with engineering engineering principles*Three axis CNC control system (fully closed loop servo control system) ensures the accurate positioning.*Modular design enables easy & convenient installation and maintenance.
-
Product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
-
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
Product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
Terminal Board
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
-
Product
Testing of Power Steering Motors
-
Endurance test bench on which up to five drives can be tested at the same time. The drives / DUTs are electrically connected to resistors and driven by a servo drive according to a predefined driving profile. This exam can take up to several days. It detects currents, speeds and temperatures.
-
Product
4-axis Pulse Train Motion Control Modules
HSL-4XMO
Motion Controller
HSL-4XMO is an advanced 4-axis remote motion control module via HSL bus. Combined with HSL I/O and motion control modules, it can meet many requirements in machine automation (MA) field. HSL-4XMO offers two models - HSL-4XMO-CG-N/P and HSL-4XMO-CD-N/P. HSL-4XMO-CG-N/P is suitable for steppers and linear motors. HSL-4XMO-CD-N/P is suitable for servo motors with transfer cable. Except the advanced motion control library (refer to PCI-8164), ADLINK also provides two extra features for users. Motion Point Table Managements can let users assign the points into the module in advance. Then, users can issue command to continuously move the points without consuming CPU resource. Motion Script Download provides users a easy interface to program the application. With this script, the DSP inside HSL-4XMO can decode the file and execute itself.
-
Product
Stepper Motor,Linear Stage,Large Load
TSAXXX-B(F)
-
Model:TSAXXX-B(F) Stepper Motor,Linear Stage,Large Load Standard products has adopted ball screw,precision products has adopted grinding screw ;Slide has adopted linear bearing;Elastic couplings adopts high-quality imported products ,ensure the machine quality .The design of limited swtiches and zero switch,standard interface are convenient for signal’s output. The handwheel in the back of motors,can achieve manual adjustment. Standard hole is convenient for combined-dimensional ;Additionally , can reload servo- motor ,assemble grating,install un-dust cover ;Application for high load and high-stability fileds ,extensively used in industry.
-
Product
Automated Programmer Superpro Sb05
-
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
Product
PCI 1-Axis Motion Controller
DMC-1417
-
The DMC-1417 for the PCI bus is a member of the Econo Series, Galil's latest generation of single-axis motion controllers which are half the size and half the price of multi-axis controllers. The DMC-1417 can handle the most demanding applications with such features as an extra encoder input for electronic gearing, program memory with multitasking, uncommitted I/O and user-selectable stepper or servo motor control.
-
Product
Safety Rated Servo Motors And Drives
-
Advanced motion safety functions including SLS, SLP and SS2 allow to complete a risk reduction strategy, and reduction in machine downtime while improving maintenance and changeover efficiency.
-
Product
Servopulser Vibration Testing Machine
EHV Series
-
This machine performs vibration tests on structures, equipment, transport packages, etc. Vibration directions include horizontal and vertical. Large capacity and large stroke can be obtained with the electro-hydraulic servo system.
-
Product
Mach Airspeed Test Fixture
TA-6055A
-
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
Product
Computer Controlled Electro-hydraulic Servo Bending Testing Machine
SBT Series
-
Jinan Testing Equipment IE Corporation
SBT series computerized bending testing machines are mainly used for bending and pressing tests for metallic sheet & round bars as per standards of GB/T232-2010 & ISO 7438-2005 Metallic Materials-Bend Test. An axial oil cylinder for bending test is installed on the top cross-head. Two pressing oil cylinders are installed at both sides of the frame, which adopts the synchronous control, to realize the pushing and pressing force on the bending support to adjust the distance between pivots. The pressure meter indicates the pressure in bending or pressing. Various load display can be selected, such as display through the pressure meter, digital display, and computer screen display etc. The computer control type SBT bending testing machine can do the bending test automatically or manually. TThe applies bending force can be adjusted or controlling the oil feed valve.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
Synchro to BCD and Resolver to BCD Converters
TSBC TRBC
-
Computer Conversions Corporation
The TSB Series are miniature, high performance, continuous tracking, synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
Electric Servo Motor Type 4 Face 3 Axis Vibration Tester
-
The electric servomotor type 4-sided 3-axis vibration tester can control 4 vibration tables synchronously or independently by combining 4 independent 3-axis vibration testers.
-
Product
Motor Stator Tester
DZ900S
-
Shanghai Aoboor Electric Co., Ltd.
Test objects include stators for single-phase AC motors. three-phase AC motors, servo motors, stepper motors, brushless motors series excitaion motors, hub motors, shaded pole motors as well asspecial winding stators.
-
Product
Digital Display Auto Torsion Testing Machine
NJS Series
-
Jinan Testing Equipment IE Corporation
NJS Series Digital Display Auto Torsion tester is designed and built for torsion test on metal & non-metallic materials, as well as parts & components. NJS is loaded through the rotation of the active cartridge driven by the AC servo motor and cyclonical pinwheel reducer motor. The torque and torsion angle are measured respectively by the high-precision torque transducer and photoelectric encoder. The digital torsion testing machine is an essential instrument to inspect torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Software
-
Besides the primary WITE32 Test Environment package at the heart of our spinstand-based test systems, Guzik offers a variety of software options to provide additional measurement accuracy and analysis. Control and Automation software enhances various electro-mechanical capabilities of the test system (such as servo accuracy), and the available suite of Analysis software tools provides deep insight into the drive component under evaluation. Adjacent Track Interference, 3D Pulse Profile, Media Scanning and Bit Error Rate are examples of some of the optional additions. Some software tools require the WDM5000 Waveform Digitizer to be part of the overall test system.
-
Product
Synchro Control Transformer
SCT-RCT
-
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems.
