Event
stream or process action.
-
Product
Pulsed IV-Curve Solutions
-
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
I2C Adapter
RS485
-
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782253-01
Multifunction I/O
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Signal Analysis
STA/LTA Detector
-
The STA/LTA Detector program is a representation of a detector of various events in triaxial or single-component time signals. The software is based on one of the STA/LTA detector types.
-
Product
Cavitation Sensors
-
Cavitation is often induced by an external acoustic field which typically has very high acoustic amplitudes but the acoustic emissions from these cavitation events are significantly smaller. The small acoustic emissions are characterised by well defined spectral peaks at integer harmonics and sub-harmonics relative to the fundamental bubble frequency.
-
Product
Compact OTDR
-
◇ 5.6-Inch outdoor-enhanced touchscreen, 7.4V/4.4Ah Lithium battery◇ Event Dead zone as lower as 1.5meter◇ Combined multi-dynamic range and wavelengths◇ Muti measurement mode, support Touching LCD and pressing keys◇ Warning function could prevent OTDR module from being damaged by optical signal in fiber.◇ Realtime measuring function, convenient to monitor the splicing process◇ Integrated 10mw Visual Fault Locator◇ Support English/ Chinese input, adopts friendly input interface, totally simulate the computer keyboard input ◇ Integrated with 8GB internal memory, more than 80,000 groups curve storage◇ PC remote access and control function is available, which support the printing work of the measurement report
-
Product
Dynamic Pressure Sensors
-
Columbia Research Laboratories
Dynamic Pressure Sensors contain low pressure measurements, high pressure transient measurements. Dynamic Pressure Sensors can measure a wide range of varying high intensity sound pressure and high level dynamic pressure events.
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782250-01
Multifunction I/O
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Power System Recorder
TESLA LITE
-
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
Product
Standalone Sporadic Event Recorder For Circuit Breakers
OTM-XB
-
The OTM-XB is the only standalone recorder to use the vibro-acoustic method that detects intermittent and sporadic operational faults on working circuit breakers.
-
Product
34-Channel Portable Logic Analyzer
16861A
Logic Analyzer
34 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
Product
Crash Simulation Systems
-
The crash simulators are capable of reproducing a wide range of standardized and user-defined crash tests including advanced applications such as side impact and vehicle pitch simulation. Instron’s acceleration sled systems are used for the development and approval of vehicle safety systems, vehicle parts and also for the investigation of solids and structures during crash events.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
Counters, Timers, And Ratemeters
-
ORTEC offers the broadest range of nuclear counters, timers, rate meters and multichannel scalers. Counters simply count the number of input pulses received during the counting period. Timers count pulses generated by an internal or external clock and are used to measure elapsed time, or to establish the length of the counting period. Rate meters provide a readout of the pulse count rate. Multichannel scalers count the number of events that occur during a specified time interval, referred to as the dwell time, resulting in a time-histogram of counts. “Standalone” and programmable computer controlled versions are available.
-
Product
Coaxlink Duo
-
Two CoaXPress CXP-6 connections: 1,250 MB/s camera bandwidthPCIe 2.0 (Gen 2) x4 bus: 1,700 MB/s delivery bandwidthFeature-rich set of 20 digital I/O linesExtensive camera control functionsMemento Event Logging Tool
-
Product
Event Detectors
STD Series
-
The STD Series Event Detectors offer test specifications associated with solder joint reliability testing but can also be used for testing other types of interconnects accordingly. Like other Event Detectors, the STD series provides continuous transient resistance detection referenced to a selected threshold resistance with a high degree of electrical noise immunity.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Longwave Infrared Thermal Camera
FLIR A6780 SLS
-
The FLIR A6780 SLS LWIR camera system makes it easy to measure temperatures of rapid thermal events and high-speed targets, making it an ideal choice for industrial, military, and manufacturing R&D applications. Thanks to its cooled, longwave Strained Layer Superlattice (SLS) detector, the A6780 provides faster snapshot speeds than other detectors for crisp images without motion blurring. Manual and remote-focus lens options provide flexibility to maximize the number of measurement pixels on the object of interest. Simple, single cable connectivity using Gigabit Ethernet provides complete camera control, plus data capturing in FLIR Research Studio software – so users can analyze and understand data faster than ever before.
-
Product
Spectroscopic Personal Radiation Detector
identiFINDER® R200
-
identiFINDER® R200 instruments are rugged, pager-sized Spectroscopic Personal Radiation Detectors (SPRD). They provide full ANSI N42.32 Personal Radiation Detector (PRD) compliance and feature next-generation solid state detector read-out technology that delivers ANSI N42.48 SPRD compliance with nuclide identification. The R200-G detects and identifies gamma radiation and the R200-GN additionally provides neutron detection capability. Law enforcement agencies and first responders use the R200 during routine traffic stops or high visibility events and in mass transit or critical infrastructure entry control points. The OneTouch Reachback™ feature uses the latest advancements in Bluetooth® and web server technologies to provide large-scale situational awareness by alerting others before arriving on-scene.
-
Product
Digital Recorder
HiRES
-
HIGHVOLT Prüftechnik Dresden GmbH
The digital recorders HiRES are used to measure, store, and evaluate signals from up to 64 sources synchronously. Depending on the sensors used voltages, currents, temperatures, mechanical movements and various other signals can be measured. This measurement system features the ability to capture fast transient processes such as those occurring in impulse current tests on electrical devices or during switchgear testing. The system is also capable of measuring semistationary and periodic events such as DC voltage and AC voltage as well as superimposed semistationary, periodic and transient processes.
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
MDS Audio Oscilloscope / Spectrum Analyser
-
Sampling frequency: 8 000 - 192 000 HzVertical resolution: 16 bitSound card selection: YESChannels count: 2Channels modes: independent, I master - II slave, II master - I slaveMath: Ch1=Ch1+Ch2; Ch1=Ch1-Ch2; Ch2=Ch2+Ch1; Ch2=Ch2-Ch1Signal reconstruction: YESPretrigger: YESTrigger events: above, below, free runInternal trigger: YESExternal trigger: two channel mode - NO, single channel mode - YESData visualisation modes: single, continuous displayFFT points count: 8 - 2 097 152FFT Window functions: Rectangular, Gauss, Hamming, Hann, Bartlett, Triangular, Bartlett-Hann, Blackman, Nutall, Blackman-Harris, Blackman-Nutall, Flat TopOscilloscope amplitude axis units of measurement: Volts (nV...kV), Sample Value (smp)
-
Product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
-
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Pulse Generators
-
Pulse generators provide electronic pulses which mimic events from radiation detectors and are useful in set-up, diagnostics, and noise measurement in spectroscopy systems.
-
Product
PCIe-6353 , PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
81049-01
Multifunction I/O
PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6353 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality … leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6353 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Building Vibration Software Module
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
*Measurement and evaluation of vibrations in buildings to DIN 4150-3 for the determination of their effects on structures*Convenient user guidance requires only short training*Comparison with limiting values to DIN 4150-3*Simple generation of reports*Detection of the main frequency*Recording of vibration events and real-time signals*External Messengers*Offline measurement*Available as kit: VM-STRUC Kit with accelerometer KS823B
-
Product
GPS Jamming & Spoofing Detection
-
Patented GPS jamming and spoofing sensor technology, available in multiple configurations to fit your application. Tested and proven for more than a decade, our unique algorithms detect live threats and take action in seconds, while outputting data for post event analysis.
