Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 2m, HV
A037DF4-T-HA200
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
3-Pin Power D-Type Cable, Female to Female, 2m
40-970-403-2m-FF
-
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 5' wires
GX96405-60
-
Mating coax connector and 20 coax pins crimped (both ends) to 5 ft wires
-
Product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
-
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m HV, Exit Towards Pin 1
A050DM5-F-HA050
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
PXIe-8431, 8-Port, RS485/RS422 PXI Serial Interface Module
781473-01
-
The PXIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Cable Assembly 44-Pin D-Type Male to Unterminated With Cut Ends, 2m
A044HM5-C-0A200
-
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Smoke Detection Sensor – 120VAC Wire-In with Battery Backup
ENVIROMUX-SDS-120V
-
For warning of smoke and invisible fire particles. Ionization smoke detector. Applications from 40°F to 100°F (4°C to 38°C). Front loading battery door. 9V battery backup (included) in case of power failure. One button design for easy testing and HUSH mode activation control. LED indicates four modes of operation: standby condition, alarm condition, alarm memory and hush mode. Hush mode: silences false alarms for 8 minutes, or low battery warning for 13 hours. Voltage supply: 120VAC. Pre-stripped wiring harness with tinned strands. Audio alarm: 85dB at 10ft. Dimensions: 5" diameter x 1.75" depth. Dust cover prevents false alarms. Tamper resist feature. Links with up to 24 devices. Max distance between first and last device: 1000ft (305m). Alarm memory indicates initiating alarm in interconnected systems. Use compatible relay (ENVIROMUX-RLY-SDS120V) for connection to the ENVIROMUX system or other auxiliary warning devices such as external sirens or stairwell lighting. ENVIROMUX-RLY-SDS120V includes normally open and normally closed contacts. Contact ratings: 10A at 120VAC, 5A at 30VDC. Regulatory approvals: UL.
-
Product
Saluki S2107 Series Optical Cable Identifier (up to 36dB)
-
S2107 Series Optical Cable Identifier is an intelligent instrument designed for the construction and maintenance of optical cable lines in optical communication system. In view of the complex wiring environment and the difficulty of locating faults during the construction and long-term use of optical cables, S2107 series can provide fast, effective and accurate fault solutions. When the target optical cable is bent or shaken, the optical cable census instrument can quickly capture the vibration signal and display it through waveform and sound, so as to locate the target optical cable quickly.
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
-
Product
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" Depth
410112702
-
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" DepthIncludes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar may be removed to allow installation or removal of cables without requiring wiring to be disconnected from the assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
CMP
-
CMPs remove unevenness on wafer surfaces that occur during the production process. Applications are growing due to the increase of layers in semiconductor devices and the growing variety of wiring materials.
-
Product
PXI 16 x SPDT Reed Relays
40-110-021
-
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
Signal, Module, ID, CASS, 210 Position, Discrete Wiring
510114106
-
Module, ID, Cass, Signal, 210 Positions, Discrete Wiring
-
Product
Switch Modules - 8 Single Pole, Form C, Discrete Power Relays which are Wired & Controlled Individually
JX8/KCP
-
This module has 8 single pole, Form C, discrete power relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. Screw Terminal Connectors and Armature power relay for switching up to 8 Amps of DC or AC current.
-
Product
SCSI-100 To 2*SCSI-50 Shielded Cable
PCL-10250
-
100-Pin to two 50-Pin SCSI-II CableHalf pitch 100 pin: Male gold flash contacts, black insulatorHalf pitch 50 pin: Male gold flash contacts, black insulator x 225 twist pairs tinned and strand copper wire with drain wireAluminum/Mylar foil and braided copper double-shielded cableP.V.C. jacketUL 20276 approvedColor : Black
-
Product
SWB-2816, 8x46, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-16
-
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, … individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF4-C-0A050
-
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 0.5m, Screwlocks
A068SFR-F-6B050
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Electrical Test Tool
-
Beijing GFUVE Electronics Co.,Ltd.
Electrical testers are useful to check for voltage, continuity, shorted or open circuits, and improper wiring.
-
Product
Wires and Pipe Locator
LKZ-720
-
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
Product
NIM and CAMAC Power Supplies
-
NIM and CAMAC crates require very clean and stable DC supplies with the standard voltages +24V / -24V, +12V / -12V and +6V / -6V. Consequently CERN defined compatible power supplies for both standards within their NIM and CAMAC specs., i.e. CERN spec. power supplies can be used on both types of crates. All "CE" version power supplies are outfitted wth separate AC wiring to comply with CE/UL safety standards.
-
Product
Modular Connectorized Distribution Unit
MCDU
-
The Modular Connectorized Distribution Unit (MCDU) is a modular family of factory-qualified subsea distribution units that provide oil-filled, pressure-balanced junctions for flexible underwater configurations.A new configuration has recently been introduced with a lighter, more cost-effective frame, highly visible ROV lifting handles, and wide openings to facilitate installation and removal of the housing. The compact frame design negates the need for lifting wires, making it easy for ROVs to install and retrieve the unit from the sea floor.
-
Product
Multi-Network Cable Tester
3PK-NT007N
-
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
Product
20-Pin GMCT Cable, Female to Female, 10A, 1m
A020GFR-020GFR-0B100
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Relay Test Jumper Kit II
60610
-
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
Product
Temperature Probes
-
Lake Shore offers a variety of temperature sensors in packages that enable mounting in very tight areas. But for some applications (especially if the sensors have to be immersed in liquid), you need to do more to protect the sensor circuitry. For these applications, a cryogenic temperature probe is the optimum choice. Encased in one of these stainless steel thermowell fixtures, the sensor can perform as designed, is unaffected by high pressure, and is sealed to keep electrical components and wiring protected from fluids and other elements.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
