Microprocessor
an IC processing logic operations to fulfill an end. Also known as: CPU
See Also: Computer, Raspberry Pi, SBC, CPU
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB116
-
The FAB116 features a PICMG 1.3 CPU card slot, one PCIe x16 slot, three PCIe x4 slots, three PCI, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB116 is compatible with Axiomtek's AX60551 and AX60552 chassis.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Half-size Backplane
HAB208
-
The HAB208 has a PICMG 1.3 CPU card slot, a PCIe x 16 slot and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two onboard SATA ports (optional function). The HAB208 is perfect fit for AXIOMTEK's half-size CPU cards, the SHB210 and SHB211, which are built around the PICMG 1.3 form factor. We have enclosures, the AX60551 & AX60552, to house the backplane.
-
Product
RMClock Utility
-
RMClock (formerly known as AMD64CLK) is a simple GUI utility designed for realtime CPU frequency monitoring and realtime adjustment of the CPU multiplier (FID) and voltage level (VID) of the supported CPUs via processor's power management model specific registers (MSRs). In auto-management mode it continuously monitors the CPU usage level (reported by CPU itself) and adjusts the CPU frequency and/or voltage level as required
-
Product
Intelligent Pressure Display Controller
HR5310/HR5311
-
HighReach Measuring & Controlling System Co.,Ltd
HR5310 intelligent pressure display controller is an intelligent pressure measurement and control product that integrates pressure measurement, display, output and control, with RS485 digital interface; the product is a fully electronic structure, using international brand pressure sensors, high-precision A/D conversion, microprocessor operation processing, on-site display, and output of one analog quantity and five switch quantities.The intelligent digital pressure controller is flexible to use, simple to operate, easy to debug, safe and reliable, and is widely used in hydropower, tap water, petroleum, chemical, machinery, hydraulic and other industries to measure, display and control the pressure of fluid media.
-
Product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
CAN Interface
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
RE Family SOTB™ Process-Based Energy Harvesting Embedded Controllers
-
The RE Family based on Renesas' innovative SOTB™ process technology realizes ultra-low current consumption in both active and standby mode and fast operation at low operation voltage, which is impossible to achieve with a conventional bulk transistor. The energy harvesting controller and 32-bit CPU also enable the development of intelligent and battery maintenance-free energy harvesting IoT devices.
-
Product
Oxygen Bomb Calorimeters
-
Labodam oxygen bomb calorimeters are designed with high precision sensors and microprocessors to get reliable and accurate results. They are designed and made as per the International Standards ASTM D5865-13 Test Methods for Heat of Coal, ASTM D240-17 Test Methods for Calorific Value of Petroleum Products, and ASTM D4809-13 Oxygen Bomb Calorimeter.
-
Product
Compact PCI Processor Board
CP67002
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP67002 is a CompactPCI® processor board based on China local-manufactured Phytium FT1500A/4 4 cores ARM processor, with more than 10-year lifecycle. Designed with ARM V8 Architecture, 28nm process technology and fine-grained power optimization technologies, the CPU integrates 4 ARM cores with CPU clock speed up to 2.0 GHz. Combined with the maximum power consumption of 15w, CP67002 is highly applicable for making low-power-consumption solutions.
-
Product
Laser Microgage
PRO
-
The Microgage PRO is the next generation in laser measuring and alignment tools. Simplifying the inspection and alignment process, the microprocessor uses Smart data technology to equip its user with step by step instructions and easy to use data giving you the answers you need.
-
Product
Broadband Power Amplifier
PAS-00210-60
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 51.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
Product
3.5” Embedded SBC With AMD® RYZEN™ Embedded V1807B/V1605B APU, DisplayPort, 2 HDMI, LVDS And 4 GbE LAN
CAPA13R
-
The CAPA13R is powered by the onboard AMD RYZEN™ Embedded V1807B/V1605B processor with Radeon™ Vega graphics. The 4K embedded board is well-suited for graphics-intensive applications such as medical imaging, video surveillance, 3D simulators, optical quality control, digital signage, kiosks/POI, thin clients, and more. The integrated AMD RadeonTM RX Vega graphics with support of DirectX 12 and OpenGL 4.5 marks the cutting edge of embedded graphics. The CAPA13R can deliver truly impressive user experiences and outstanding 3D graphics quality through two HDMI, one DisplayPort and one LVDS interfaces. Its onboard CPU is attached on the rear side of the board, which can aid with heat dissipation and offers flexibility for easy system integration and minimum maintenance. Moreover, the CAPA13R offers multiple expansion interfaces with one M.2 Key E slot for wireless modules and one M.2 key B slot for storage cards. One 260-pin SO-DIMM socket on the CAPA13R supports up to 16GB of DDR4-2400 (V1605B) and DDR4-3200 (V1807B) memory. The system has a +12V DC power input.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
CPCI Integrated Communication Card
MS 3635I
-
CPCI Integrated Communication Card is high end Microprocessor based Mixed RS422 Communication and Differential Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have Synchronous RS422 Communication Interface, Asynchronous RS422 Communication Interface, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic storage and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
Product
Pressure Transducers with CAN Bus Interface
P66
-
The Validyne model P66 is a digital differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via CAN Bus provides remote zero and span adjustment as well as digital pressure readings in engineering units or pressure counts.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Electric Vehicle Battery Cell Tester
MCV
-
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
Product
Computer On Modules
ETX/XTX
Computer on Module
ETX / XTX CPU module eqiupped with Intel Atom has great I/O capacity and meets both ISA and PCI needs, while supporting the Computer On Module concept for plug-in CPU modules. Advantech is a founding member of the ETX Industrial Group (ETX-IG).
-
Product
Trusted Platform Module Compliant With TCG 1.2 / 2.0 Specification And TCG Software Stack 1.2 / 2.0 Via LPC Connector On CPU Card.
PCA-TPM
-
TCG 1.2 / 2.0 specification and TCG software stack 1.2 / 2.0 via LPC connector on CPU card.Hardware based data protection solution for storage device encryption and decryption.Dimension: 31.5 x 30.5 mm
-
Product
LTE-A Router
ICR-4233
-
ICR-4200, EMEA, 2× ETH, 2× RS232/RS485, USB, SD, Without Accessories. LTE-Advanced Cat.6 Cellular Connectivity. Quad-core CPU with 1 GB RAM.
-
Product
Portable Trace-Level O3 Calibrator
Model T753U
-
Teledyne Advanced Pollution Instrumentation
The Model T753U is a portable, microprocessor based precision Calibrator for Ozone gas instruments and sensors. Using a sophisticated Ozone generation system, combined with a sensitive photometer and pneumatic design, the T753U produces stable and reliable concentrations of Ozone in a convenient and rugged package based on our popular T750U Portable Multigas Calibrator platform. The T753U is housed in a high-density, molded travel case which includes an integral handle and wheels for durability and ease of use in the field for virtually any application. An internal zero air option extends the T753U's capabilities to also provide a clean and dry source of zero air, eliminating the need for a separate source of zero air. The internal zero air source module contains a software driven electronic inlet valve manifold allowing the calibrator to automatically switch between internal and external zero air sources depending on the application needs.
-
Product
Industrial PC/104-Plus AMD LX800 x86 Single Board Computer
PPM-LX800-G
-
The PPM-LX800-G is a highly integrated, industrial PC/104-Plus single board computer (SBC) designed for embedded, space-limited, low power applications. It is a full-featured SBC that includes an AMD LX800 x86-compatible CPU, CRT and flat panel video controller, 10/100 Ethernet, two USB 2.0, 16 lines of digital I/O, and four COM channels on a single 3.6 x 3.8 inches (90 x 96mm) module.
-
Product
1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 10 PCI™ Slots Backplane
EBP-13E2
Backplane
- Segment: 1- Slots: 1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 10 *PCI™- Support ATX power supplies- Dimension: 330 mm x 318 mm
-
Product
FireBird Camera Link Frame Grabber (2xCLM-2PE8)
AS-FBD-2XCLM-2PE8
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787880-01
Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Camera Link Adapter Module For FlexRIO
Module
The Camera Link Adapter Module for FlexRIO supports 80‐bit, 10‐tap base‐, medium‐, and full‐configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the Camera Link Adapter Module for FlexRIO with a PXI FPGA Module for FlexRIO for applications that require bit‐level processing and very low system latency. With the Camera Link Adapter Module for FlexRIO, you can use the FPGA to process images from the camera in-line before sending the images to the CPU, enabling more advanced preprocessing architectures.
-
Product
Digital ELCB Tester
KM 1812 EL
-
Kusam Electrical Industries Limited
2 Lines x 16 Characters L.C.D. Very Low Power Consumption. Microprocessor Controlled. Menu Driven. Accurate digital readout of disconnection Time.
-
Product
PICMG 1.3 Half-size SBC
-
Axiomtek's PICMG 1.3 half-size CPU cards (185 x 126 mm) offer high performance PCI Express slot as interface to the backplane, and improve I/O bandwidth and graphic performance from the original PICMG 1.0 specification. The PICMG 1.3 half-size SBC is specially designed for space concernd applications.
-
Product
2 PICMG® CPU, 10 PCI™, 4 ISA Slots Backplane
HPCI-15S10
Backplane
- Segment: 1- Slots: 2 PICMG® CPU, 10 PCI™, 4 ISA- Supports AT, ATX power supplies- Dimensions: 317 mm x 264.2 mm
-
Product
Ultrasonic Flaw Detector
MFD660C
-
MFD660C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed premium product, has a lot of advantages like unique design, sophisticated manufacturing, convenient operation, powerful function. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it can select the operating interface style and the LCD brightness according to environment. With humanizing interface design, the waveform show delicately. It can find the defects clearly in full screen. Single hand capable for holding operation, the curve making, probe calibration and other conventional operation can be completed automatically. Core processor CPU with 400M main frequency, it can complete the complex run quickly and realize intelligent defect analysis. Low power design with large capacity and high performance lithium ion battery module， it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways in one body, customers with different habits can operate it freely. It supports many languages. Its waterproof, oil proof, dustproof function can achieve IP65 protection level. It is the necessary professional precision instrument for defect detection, quality control, on-line safety monitoring and life evaluation in fields of oil, chemical, metallurgy, shipbuilding, aviation, railways and so on.
-
Product
LAN Router
ICR-3201W
-
ICR-3200, Global LAN, 2x Ethernet, 1x RS232, 1x RS485, Wi-Fi, Metal, Without Accessories. LAN VPN Gateway for Industrial IoT applications. Powerful CPU with 1.3 GB storage to host customer SW applications.
