Navigation Aid Panel Tester

Ground Support Equipments

Meltronics Systemtech Ground Support Equipments

Company Catalog Share Add To List

ARINC429 Data Bus Analyzer is portable equipment used for Avionics technicians and line maintenance personal with convenient, easy to use tools for stepping and troubleshooting ARINC429 Avionics System. This Equipment has dual channels for transmitting, receiving and displays the ARINC429 data.

Company Catalog Share Add To List

Accelerometer & Platform Test Bench

mS 1115 - Meltronics Systemtech

Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.

Company Catalog Share Add To List

Break In Break Out Box

MS 3648I - Meltronics Systemtech

Break in Break Out Box is standard portable 19” rack mountable with 128 Input and 128 Outputs.

Company Catalog Share Add To List

Combined Map Display Unit & Interface Unit Tester (COMED)

MS 1117 - Meltronics Systemtech

This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.

Company Catalog Share Add To List

Data Retrival and Analyzer Unit

MS 1200 - Meltronics Systemtech

*Retrieves the Data from Magnetic / Solid State Recorders (Supports JAGUAR, AN32, IJT, ALH Platforms)*RS232/RS422/Bi-Phase/USB interface with PC AT*Presents Error Messages and Test Reports*Replay, Analysis and printout of selected parameters*Calibration facility for ADR and DAU*Portable System for Snag Analysis of Aircraft*Reports in Tabular/Graphical formats*Used to check serviceability of ADR, DAU without removing from aircraft

Company Catalog Share Add To List

EMU & Mission Data Programmer

MS 1603 - Meltronics Systemtech

The EMU – MIP programming station is used to program, read and erase mission data of Mirage 2000 Aircraft and it has additional feature of programming the Extended Memory Unit. It has 3 EMU Slots (1 Read only) and 5 Slots (1 Read only).

Company Catalog Share Add To List

Engine Simulator

MS 1118 - Meltronics Systemtech

Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.

Company Catalog Share Add To List

Engine Speed Control and Measurement (Test Set A)

MS 1100 - Meltronics Systemtech

*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states

Company Catalog Share Add To List

Engine Vibration Measurement Unit

MS 1101 - Meltronics Systemtech

*Used to check engine vibration level*The seismic transducer mounted on both engines*Used for the measurement of vibration levels for various engine rpm*Used for the measurement of amplitude on each frequency component

Company Catalog Share Add To List

Gyro Evaluation & Test Equipment

MS 1113 - Meltronics Systemtech

The automatic test bench for gyros (ATP) is used to carry out the final acceptance test for the gyros in the stand-alone mode. It is a PC based test set up incorporating standard and custom built test and measuring instruments interfaced by GPIB bus. The gyros are installed on the platform, which is used to provide information pertaining to the angle at which aircraft is flying.

Company Catalog Share Add To List

Interface And Load Box

MS 3646I - Meltronics Systemtech

Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.

Company Catalog Share Add To List

Mission Data Programmer

MS 1602 - Meltronics Systemtech

The MIP programmer is used to program, read and erase mission data of Mirage 2000 Aircraft. This system is micro controller based design. This system facilitates to program the four EPROM devices at a time. This system contains four read write slots and one read only slot. Read only slot used to read the device data safely. System also has capability to program the one slot device data to another slot device.

Company Catalog Share Add To List

Multi Output Buffer Unit

MS 1632 - Meltronics Systemtech

The Multi Output Buffer Unit is used for driving singe input to 32 outputs. This unit drives an analog input to two different 16 set of outputs through two 50 Pin standard D Type connector. The unit works on standard 230V AC.

Company Catalog Share Add To List

Power Bus

MS 1606 - Meltronics Systemtech

The PowerBus is used to service printed circuit boards, instruments and systems, which has Micro controller / Microprocessor. The PowerBus has RS232 Communication for PC interface. The PowerBus connects to the UUT through the microprocessor / micro controller socket. The UUTs microprocessor / micro controller is removed from the UUT and it is replaced by the PowerBus. The Power Bus adapts microprocessor specific function as pin layouts, status / control function, interrupt handling, timing and memory and I / O addressability.

Company Catalog Share Add To List

SCT IFCC Self Test Box

MS 3647I - Meltronics Systemtech

SCT-IFCC Self-Test Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has testing facility of all Inputs and outputs of Single channel tester of IFCC.

Company Catalog Share Add To List

Single Channel Tester

MS 3600I - Meltronics Systemtech

The Integrated Flight Control Computer (IFCC) is the central control computer for the RPFA. IFCC consists of flight control computer, Air Data Computer, Aircraft Encoder Decoder unit. The Single Channel Tester is the automatic test equipment to test the IFCC. SCT shall be used to perform the hardware ATP of IFCC.

Company Catalog Share Add To List

Surface And Subsurface EW System Tester

MS 1119 - Meltronics Systemtech

CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.

Company Catalog Share Add To List

UAV Ground Test Equipment (LTS)

MS 1103 - Meltronics Systemtech

*Checks integrated functionality of UAV*During integration checks it performs the functions of the Ground Control Station*Interface with Target Group Set (TGS)*Information is decoded and displayed in the display panel

Company Catalog Share Add To List

UNA Programmer

MS 1604 - Meltronics Systemtech

The UNA programmer is used to program the UNA board. The UNA Programmer is a processor-based system. The UNA Programmer performs the Blank checking, Programming, Reading and Verification

Company Catalog Share Add To List

WCS Simulator

MS 1601 - Meltronics Systemtech

The WEAPON CONTROL SYSTEM SIMULATOR (WCSS) is used to simulate Aircraft Bomb and Rocket release commands for the LAB testing of WCSTS. The WCSS system simulates the High current and Low current signals according to the mode of operation (Series).

Company Catalog Share Add To List

9U ATE Rack

MSMI 1014 - Meltronics Systemtech

- Capable of handling up to 2688 IO signals- Capable of handling up to 1344 Power signals- Portable and Rack mountable- Suitable for more depth PCBs (up to 410mm)- Fourteen PCBs can be accommodated with Fascia plate of 30 mm width

Company Catalog Share Add To List

Weapon Control System Test Set

MS 1102 - Meltronics Systemtech

- Provides serviceability checks on armament system- Portable instrument- Check the Bomb release sequence, practice bomb release sequence, rocket release sequence, fuzing, and jettison of aircraft stores- Helps to identify faults of conventional armament- Microprocessor based design

Company Catalog Share Add To List

SSFDR Software Integration Rig

MS 1112 - Meltronics Systemtech

Software Integration Rig (SIR) is an Industrial PC based system is used to test the SSFDR (Solid State Flight Data Recorder) of SU30 Aircraft. SIR is a PXI based test platform and it is used to test independent and integrated software tests of the SSFDR.

Company Catalog Share Add To List

Centralized Warning Panel

MS 1116 - Meltronics Systemtech

The Centralized Warning Panel Test Rig is used for conducting Pre Installation Test of Airborne Centralized Warning display unit of Advanced Light Helicopter.

Company Catalog Share Add To List