Logic
-
Product
Fire, Gas & Intruder Controllers & Alarms
MultiSafe-MX
-
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
Product
RFSoC Board
VP430
-
RFSoC on 3U VPX: the VP430 direct RF system features an RFSoC with integrated ADCs, DACs, programmable FPGA logic, and Zynq ARM Cortex processor.
-
Product
16-Ch Sink-Type Digital Output EtherCAT Slice IO Module
AMAX-5057
Digital I/O Module
Channels:16 (Sink Type)Voltage Rating:10~30VDCRated Current Output:0.3A per channel atsignal "1"Leakage Current:25 μA per channel atsignal "0"Output Delay:From logic level 0 to 1:10μs;From logic level 1 to 0: 100μs
-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
785045-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V,based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
Diagnosis Device
CANtouch
-
The CANtouch is a battery operated handheld diagnosis device for physical and logical CAN bus analysis. With its modern touch control it allows an intuitive and efficient handling without an additional computer.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
KX-155A Display Assembly Extender Card
KX155-EXT
-
The KX-155A Display Assembly Extender card will give the technician access to troubleshoot a display problem on this Bendix/King Nav/Comm. The card breaks out all pin connections with their functions silk-screened on the board. This board will allow the technician to make a more logical decision on what the problem may be. We have seen in our shop that the glass display is not always the failed componet.
-
Product
Microprocessor Development System
DS-48
-
# Real-Time and Transparent In-Circuit Emulator# Supports Philips Telecom Derivatives# Adaptable to 8051 Derivatives# Emulates 1.5V to 6V Microcontrollers# Maximum Frequency of 40MHz# 8K of Internal Memory# DOS and MS-Windows Debuggers# 32K Trace Memory and Logic Analyzer "on the Fly"# 8K Hardware and Conditional Breakpoints
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
8-Ch Isolated Digital Input Module
ADAM-5052
Digital Input Module
Digital input level: Logic level 0: +1 V max.Isolation voltage: 5000 VRMSPower consumption: 0.27 W (max)Channels: 8
-
Product
Time Controller
ID900
-
IDQ’s Time Controller is an all-in-one device designed for flexibility and it efficiently solves a large number of problems encountered in the laboratory. Its core consists of 4 high-speed (<20 ps precision, 100Mcps rate) inputs and 4 high-speed outputs, interconnected by reconfigurable logic. The Time Controller performs the functions of a number of devices: time-to-digital converter, coincidence counter, delay generator, pattern generator, counter and discriminator. This is complemented by a 10Gbps link to the host computer for fast data transfers, by auxiliary analogue and digital I/O for interfacing with external devices.
-
Product
Protocol Control Control
PC2
-
The PC2 software from SCSI Toolbox, LLC brings a new level of parallel SCSI protocol control to your test environment. Designed in cooperation with LSI Logic to work with their Fusion-MPT Message Passing Interface technology, PC2 allows all negotiated parameters to be displayed or set for all devices connected to any SCSI Host Bus Adapter based on the LSI53C1030 chip set. PC2 also provides the means to generate hardware SCSI bus resets.
-
Product
PXI Digital I/O Modules
-
Pickering's PXI Digital I/O Modules are suitable for operating external devices or for interfacing with external logic. Two choices of output drivers are available:*TTL for interacting with external logic*Output channels for operating external devices with voltages to 60VDC and current to 2A
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
783907-01
Digital Module
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, … features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
Rad-Hard Logic ICs
-
ST offers a large selection of rad-hard logic ICs for space applications, including:
-
Product
Internet Of Things
IoT
-
In a world of smart, connected everything, Altair empowers you to harness the power of the Internet of Things (IoT) to accelerate innovation and unlock business value. Leveraging our dynamic toolset you can deploy edge compute clusters, train and execute machine learning models, implement complex application business logic, perform data transforms, visualize real-time data, and much more. We give you the building blocks for your digital transformation to get moving fast, scale quickly, and continue to improve over time.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
PXI I/O Board
MZ-TrigIO
Digital I/O Module
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
Product
PXIe-6544, 100 MHz, 32-Channel, 3.3 V PXI Digital Waveform Instrument
780992-02
Digital Waveform
PXIe, 100 MHz, 32-Channel, 3.3 V PXI Digital Waveform Instrument—The PXIe‑6544 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The PXIe‑6544 can sample digital waveforms at up to 100 MHz and interface with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6544 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
PXI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module
779313-01
Digital I/O Module
16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module—The PXI‑6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety, the PXI‑6521 requires a keyed connector. If a computer or application fault occurs, the PXI‑6521 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
-
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Osprey ISA Q-Bus Adapter board
9476-Q-B
-
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
Product
PXI 16 to 1 Mux 1GHz 50Ohm SMB
40-747-511
Multiplexer Module
The 40-747 is a single 16 to 1 RF MUX available in 50 Ohmhm or 75 Ohmhm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohmhm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-747 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals
-
Product
16DI IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6251
Digital Input Module
16ch digital input(counter)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
-
Product
Complete Data Acquisition System
ScopeLogicDAQ
-
ScopeLogic - complete data acquisition system - consists of Digital Oscilloscope and Logic Analyser. This small instrument is making the accurate analysis of complex analog-digital signals possible - thanks to simultaneous sampling finding relationship between these signals is easy. The user is able to simultaneous use 16 digital channels and 2 analog channels with standard scope probes.
-
Product
16-Ch Digital Output Modules
ADAM-5056D
Digital Output Module
Operating voltage: 30 VmaxDigital output: Open collector to 30 V, 100 mA max. loadOutput status hold functionPower consumption: 0.5 W (typical); 0.84 W (max.)Power dissipation:300 mW for each channelLED indicator: On: Output logic level "1"Channels: 16
-
Product
Multiprotocol Transceivers
-
Analog Devices’ RS-232/RS-485 multiprotocol transceivers are the only parts in the market that allow protocol switching and allow for switching between half-/full-duplex operation and switching on/off termination resistors, both of which minimize physical user intervention when reconfiguring networks. Features include 3.3 V to 5 V operation, up to ±26 kV ESD, a logic supply pin, and small LFCSP packages. As large-scale computing applications typically require more protocols than the RS-232 and RS-485 protocols found in everyday applications, we support legacy protocols. These include V.28 (RS-232), V.35, RS-449, RS-530, RS-530-A, V.36, or X.21. Software-selectable protocol, cable termination, and data terminal equipment (DTE) or data communications equipment (DCE) configurations all provide convenient flexibility.
-
Product
PXIe Vector Signal Analyzer: 6 GHz
M9391A
Vector Signal Generator
RF requirements keep growing while timelines keep shrinking. To help ease the technical and business pressures, the right test solution provides continuity in measurements and longevity in capability. In the evolution of modular RF test solutions, the Keysight PXI VSA is the next logical step in signal analysis. With raw hardware speed and X-Series measurement applications, it delivers proven results faster. From fully modular hardware to software leverage to worldwide support, the PXI VSA is the low-risk way to manage change and be ready for tomorrow today
-
Product
Oscilloscope, 100 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2104HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
16DO IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6256
Ethernet I/O Module
16ch digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
