Filter Results:
Products
Manufacturers
Applications
Logic
-
product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
product
Social Engineering With Physical & Logical Attack
LGMS Security Team will approach the Social Engineering assessment as an intelligence operation. During the course of assessment, LGMS Security Team will base on clear objectives to breach the security controls using information that has been obtained through deception including phishing emails, sending of malicious parcels (CD or thumb-drives), and social engineering phone calls.
-
product
Logic Analyzer
FS2352B
The FS2352B is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR3 DIMMs. This logic analyzer probe has a CKE qualification circuit that allows for the use of older Keysight logic analysis modules when testing systems using power saving modes.
-
product
BusFinder Protocol and Logic Analyzer
Acute BF7264B+
*Two-in-One Analyzer (Protocol and Logic)*PC-based, 64 channels*USB 3.0 interface, 12V power adapter*32Gb total memory*NOW supporting MIPI D-PHY 1.2 (includes MIPI CSI)*NOW UFS2.1 supported with new BF7264B+
-
product
PCIe FPGA Carrier For FMC+, Kintex UltraScale™
PCI592
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
product
PC-based logic analyser
Annie-USB
A top-quality 8-channel PC-based logic analyser with probably the highest specifications in its class, this Janatek product is excellent value for money. It captures data at a maximum rate of 500MHz, has a buffer depth of up to 1 Meg samples per channel, and incorporates an 8-bit pattern generator to aid debugging.
-
product
Buffers/Drivers
ST's automotive logic IC portfolio includes quad and hexadecimal bus buffers from the 74LCX, M74HC and HCF families offering excellent latch-up performance, power-down protection on inputs and outputs, low power dissipation and high noise immunity.
-
product
Embedded Boards
UltraZed Family
Embedded boards are boards with processors, multiple integrated circuits, interfaces and other essential components assembled on it to serve a dedicated function. Embedded boards comprise multiple technologies, including processors, core logic, networking, connectivity, and multimedia components to provide functionality and performance for embedded system design applications. Embedded boards and solutions are normally employed to ensure a faster time to market for the developer. Applications of embedded systems vary from tiny portable devices, to large commercial and industrial installations, and even largely complex systems like medical or military or aviation purposes. Embedded boards can have single MCU chip or multiple MCUs depending on the complexity of application.
-
product
Programmable Current Preamplifier
99539
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
783734-01
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
product
PXI I/O Board
MZ-TrigIO
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
product
System Integration
The provision of a basket of services for Auditoriums such as audio-visual systems, stage lighting, stage rigging, building control systems, communication systems and information technology systems. A proper understanding of the various disciplines involved is the key to successfully integrating the diverse component parts. The final solution must perform as one unit with a high degree of simplicity to the end-user. The result will be a solution that, while extremely complex, appears simple, logical and easy to use. Sri Comm has successfully designed, installed and commissioned several projects of this nature.
-
product
Input-output Module
OLS
The OLS module is a specialized device for input-output of logical information, intended for the formation and registration of asymmetrical logical levels of signals on 64 channels. The OLS module is made in the VXI standard and is functionally close to the DI-Series modules from Teradyne.
-
product
DDR4 X4/x8 BGA Interposer For Logic Analyzer, Connects To 61-pin ZIF
W4643A
The W4643A DDR4 2-wing BGA interposer for DDR4 x4/x8 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A. The W4643A is the smallest BGA interposers for DDR4 x4/x8 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding 3.2 Gb/s. U4208A and U4209A probe/cables connect any W4640A Series DDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W4640A Series BGA interposer wings.
-
product
DC/DC Converter 150 W
CQB150W-110S3V3N
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 3.3 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke | negative control logic
-
product
8-Channel 250 MHz A/D with Virtex UltraScale+ HBM FPGA - SOSA Aligned 3U VPX
Model 5585
- Jade 5585 and 5586 FAQ- Complete radar and software radio interface- Wideband data acquisition- Multi-channel, multi-board synchronization for high channel count systems- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX processing powerhouse- Exceptional dynamic range and analog signal integrity- Features Xilinx Virtex UltraScale+ HBM FPGAs- Eight 250MHz 16-bit A/Ds- 10 GigE Interface- 40 GigE Interface- Dual 100 GigE UDP interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Navigation Design Suite for software and custom IP development
-
product
16 Bit Digital Card
DB1600
The DB1600 is an inexpensive digital card that provides basic digital control capability without some of the more sophisticated features available on the DRM1650. The DB1600 allows for the control of 16 bits of data. The logic levels may be programmed anywhere within the range of 12 V.
-
product
High Power Noise Sources
NS-7001
The NS-7001 is high-power noise source specifically designed to operate in the 2.11-2.17 GHz UMTS band. It features flat output power that is regulated over a wide temperature range with high rejection outside the operating band of interest. Logic control is provided to enable/disable the noise source and an internal BIT function continuously monitors the output power. Other frequency bands and power levels are available.
-
product
PFR96
2WE06
The digital controller PFR96 can manage up to 12 independent batteries, a communications port, and two current inputs in size from 96×96 framework. Particularly easy to program thanks to a basic configuration with two parameters and advanced that allows the advanced user the most complete of the power factor correction control.The onboard logic allows corregegre setup via an erroneous wiring of the picture as to or stage of TA.10ms sampling of the voltage allows the calculation of the RMS voltage continuously, identifying network holes and temporary interruptions and detach the active steps immediately to the protection of the contactors and benches.The PFR96 can handle numerous alarms associated to available relays.The means of intervention in the PFR96 adjustment are all customizable for a better quality of the intervention as well as the use of different banks can be equalized for less wear of the contactors.Sampling at variable frequency and RS485 communication for remote control (PFR96 Plus) complete a range of services offering maximum control and quality of the measurement
-
product
CPCI ARM LPC3250 Board
MS 1513
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
product
Bluehill® Universal Software
Bluehill Universal from Instron is a modern, touchscreen‐first software platform designed to make materials testing simpler, smarter, and safer. With intuitive, guided workflows, prebuilt method templates for ASTM, ISO, and EN standards, and dynamic features like barcode integration, pass/fail display, and conditional logic, it streamlines testing tasks and reduces user error. For more advanced users, modular options—such as TestProfiler for cyclic tests, Traceability for full audit trails and 21 CFR Part 11 compliance, and seamless API support—enable customization, data integrity, and lab‑wide connectivity. Whether deployed on new Instron systems or retrofitted into existing hardware, Bluehill Universal offers enhanced usability, robust security, and flexible data handling for next‑generation materials testing labs.
-
product
Kestrel /SX Co-Processor
0149-SX
Same speed Windows/NT Kestrel Co-Processor for equivalent system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.
-
product
Darlington Arrays
Darlington devices are high-voltage, high-current switch arrays containing multiple open-collector Darlington pairs or multiple Darlington transistors with common emitters, and integral suppression diodes for inductive loads. The nominal current rating of each output is 500 mA for the 7- and 8-output devices and up to 1.5 A for quad-output devices. The inputs are pinned opposite the outputs to simplify the application board layout. These devices interface standard logic families.
-
product
Software
HyperWare-II
HyperWare-II™ (HW-II) is a powerful multi-purpose software package for use with the Logic Beach Network Enabled IntelliLogger and the IL-Mini data logger data logging instrument families. HyperWare-II™ is the next generation icon-based data logging software built upon the original industry-preferred HyperWare program and contains all the functions required for configuration and use of the IntelliLogger.
-
product
Digital Storage Oscilloscope
Qingdao Hantek Electronic Co., Ltd.
Fluorescent oscilloscope is up to 400,000 FPS.It has 256 grade color and color temperature display.Standard equipped with up to 16 kinds of trigger functions, 5 kinds of serial decoding functions.It supplies 200 MHz, 100 MHz and 80 MHz bandwidth, its memory depth is up to 64M,16 channels logic analyzer plug and use, all standard equipped with 2 channels waveform generator, standard equipped with touch screen. it is a useful commissioning instrument for various fields such as communication, aerospace, defense, embedded systems, computers, research and education.
-
product
Digital System Controller
SC-20
The SC-20 system controller is capable of executing an entire coating run with the push of a single button. The backlit LCD display provides an easy way to monitor the coating and system status while running. The SC-20 can communicate not only with other Eddy process controllers, but with most OEM controllers as well. This makes it a perfect candidate for system upgrades as well as new builds. Noise protected circuitry coupled with continuous logic software ensures the process will be controlled and monitored throughout the whole process.
-
product
SP5T RF Pin Diode Switches To 12 GHz
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
product
BCD to Binary Converter
BCD250
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
product
Universal Plug-in Module With I/O And CAN FD Interface
PCAN MicroMod FD
The PCAN-MicroMod FD is a small breadboard with CAN and CAN FD connection on the one hand and various physical inputs and outputs on the other. Both sides are logically linked using the NXP LPC54618 microcontroller. Electronics developers can use the PCAN-MicroMod FD to easily integrate I/O functionality with a CAN connection into their project.
-
product
Multi-Function PXI Card
GX3788
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
