Radio Test Sets
See Also: TPS
-
Product
Digital and Mixed-Signal Test Solutions
-
A digital device processes electronic signals that represent either a one (on) or a zero (off). The ‘ones’ and ‘zeros’ represent data. Each one or zero is referred to as a bit and a group of 8 bits equals a byte
-
Product
RF Near Field Probe Set DC to 9GHz
-
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
Product
Cell, Module & Pack Testing
-
Cell, Module and pack battery formats are crucial for electrification in transportation and energy. Arbin Instruments' test equipment is designed for performance-based tests, to meet the needs of these complex formats.
-
Product
Strategic Test Management
-
Large programmes and projects require a strong test management function to oversee the delivery of the testing phases. Where in-house systems and external vendor's elements of delivery meet, communication and a strong test approach are key. Our test management consultants are the best in the business. With our years of experience, we will drive your test process to succeed.
-
-
Product
High-Voltage Test Device
PGK 150 / 5 HB
-
Cable testing and diagnostics with the BAUR PGK H. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 150 kV output voltage with positive or negative polarity* AC voltage testing - up to 110 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
Testing and Validation
-
DA-Group offers accredited testing services for a wide range of electronic and mobile solutions and products. Testing and measuring are necessary during many phases of product development, manufacturing, verification and delivery. Timely and appropriate testing saves time, because this information is fed back to the development process.
-
Product
Piers and Jetties Testing Equipment
-
The BathyCorrometer is a diver-held unit which will measure the corrosion potential at specific contact points. Although the readings are visible to the diver, a Surface Display Unit can be supplied to verify readings on board a ship or diving platform. If Remotely Operated Vehicles (ROVs) are being used, the UCP1A contact probe or UCP1B proximity probe can be easily installed to carry out corrosion surveys. Simple surveys of marine structures can be carried out by the use of a Marine Survey Kit (see the case study on Dover Harbour Board).
-
Product
Color Wheel Test Kits
-
The color discs use a visual comparison method (color matching) to determine concentration. Simply add reagents to the sample and turn the wheel until the sample matches the reference color. The concentration is displayed in a window.
-
Product
MPO/MTP Polarity Testing Machine
-
Anfkom International Co.,Limited
12 Channel or 24 channel optional. One key button exchange, no need speical order and design 24 channel equipmentsSupport the 12/ 24 channel fan shape line detectionShort testing time.7″ color screen display, testing result are intutive and clear.Compatible with 9/125,50/125,62.5/125 fiberdetect unqualified have warning voice prompt, reduce misjudgement rateSupport custom 12 channels/24 channels fiber optic patch cable wire sequencethe data do not disappear when power supply drop.
-
Product
Camera Testing Equipment
Meridian®
-
From smartphones and webcams to drones and automotive safety systems, compact cameras are everywhere, and expectations for image quality have never been higher. The Meridian® product family from Optikos delivers powerful, space-efficient solutions for testing today’s small-format, wide-field cameras.
-
Product
Stator & Coil Testing
-
Electronic Systems of Wisconsin, Inc.
ESW Stator Test Systems come fully equipped with the latest industry features. The on-screen display in our testers allows the operator to visually see the part lead hook-up to the tooling connections. Our software makes it easier to read, track, and record your stator test information. While performing tests, you can watch the testing throughout the process in real time. You can view various wave-forms for surge or magnetic field, which can be displayed real-time and printed if desired. The software logs all test results, so that you do not have to worry about losing important information. ESW designs the tooling to be simple to connect the part. We work closely with you to define and implement your customized testing needs. The videos and slideshow below show some of our Stator Testers.
-
Product
EMC Test Equipment
TDEMI eXtreme series
-
Highest measurement speed. Highest accuracy. Incredible dynamic. New operation modes. The novel product line TDEMI eXtreme (TDEMI X) is the latest and most advanced level of full digital measurement equipment for emission testing on the fast lane. It is based on the unrivaled and patented TDEMI® real-time technology of GAUSS INSTRUMENTS. It is easy and efficient in upgrading its frequency range by a various number of extensions which can be integrated into the instrument step by step. The frequency ranges are 1 GHz, 3 GHz, 6 GHz, 18 GHz, 26.5 GHz or 40 GHz respectively. A large variety of configuration possibilities makes the TDEMI X to the customized solution perfect fitting into your lab and to your application according to civil standards (e. g. CISPR, EN, FCC Part 15, ANSI C63.2, ANSI C63.4), military standards (e. g. MIL-461G, but also its previous versions and revisions) as well as avionic standards (e. g. DO-160). The frequency range of the TDEMI X instruments starts at 9 kHz in its standard configuration and can be extended down to 10 Hz by the option MIL/DO-UG or even down to DC by the available option OSC-UG as well. Like all other TDEMI measurement systems, the TDEMI X measurement systems can be remotely controlled and fully automated via Ethernet (TCP/IP) very easily.
-
Product
Tri-Axial Vibration Test Tool
-
AMHS and conveyor manufacturers utilize the Tri-Axial Vibration Test Tool to quantify and qualify the vibration characteristics during development, installation and maintenance of their systems. This industry-standard tool is used by 200mm and 300mm FABs to measure the vibration induced to wafer lots by their material handling systems. By detecting the early signs of track misalignment, systems can be maintained to minimize the vibration induced on the wafer lots.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Strain Gauge Test
-
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
Product
Test Equipment
ST6300
-
Shenzhen Star Instrument Co., Ltd.
The ST6300 portable three-phase meter test equipment is suitable to conduct commissioning and testing for energy meter manufacturers and meter test departments. It adopts modular design and incorporates DSP and PWM switching amplifier technologies. Users are able to control the equipment via keypad or PC-based software. It simultaneously measures the errors of three energy meters. It connects to a meter rack via its COM port.
-
Product
Test Tables / System Solutions
-
WEETECH, as a manufacturer of test equipment, offers its customers also a "Ready To Use" test system solution. It consists of the test table, the customer-specific adaptation as well as the test device, and is very quickly ready for use at the customer's site. According to the customer's requirements, the set-up is designed as a system with permanently installed adaptations for the production of constant cable harnesses in large quantities or with interchangeable adapters for the flexible production of different cable harnesses. Depending on the application, a larger table version or a smaller desk version is available. Various interfaces are available for integrating these solutions into a complete production automation system.
-
Product
Multi-Stage In-Circuit Test Fixtures
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
Hazardous Locations Product Testing
HazLoc
-
F2 Labs can assist you with your hazardous location testing needs. We can perform the HazLoc product testing required to ensure that your product won’t cause a fire or explosion in an area where flammable or combustible materials (such as dusts, gases, fibers or vapors) are present. The product must be designed using various methods of protection.
-
Product
High-Speed Impact Testing Machines
HITS-X Series
-
With the increasing demand for safety and reliability, evaluation of the dynamic strength (impact properties) of materials and parts is becoming more and more important. This machine can obtain data, such as the maximum test force, energy, and displacement, up to a maximum velocity of 72 km/h (20 m/s). A tensile load type (HITS-TX) and a punching type (HITS-PX) are available.
-
Product
Efficiency Test
-
Type test stands for industrial electric motors*Testing of 1-phase and 3-phase asynchronous and synchronous motors up to 3 kW*Speeds up to 30000 1 / min
-
Product
USB Test Hardware
-
Test stations with USB hardwareHardware control of adapters with USB-I / OFlash and microprocessor programmer
-
Product
METES - Meter Test Systems
-
Dramatic advances in the field of measurement technology and the use of state-of-the-art micro-electronics have led to the development of a new generation of electricity meters which are far more accurate than their predecessors of just a few years ago. As well as measuring the exact amount of energy used, a high level of integration enables electronic meters to perform a number of additional functions. As a result, these meters are also more sensitive to network irregularities. This means that regular testing is the only way to ensure that a meter functions correctly, both during final factory tests and during the entire life span of a meter.
-
Product
Calibration and Test Equipment Management
-
Is every value precise? The comparability of measurement results has never been more important than in the present era of globalization. The ability to reduce variables to basic units is the fundamental prerequisite to objectively guarantee, increase, and optimize quality. Our calibration service guarantees full correlation to national standards for test equipment of all physical variables – either at our laboratory or on your premises (for measuring tools).
-
Product
In Situ Testing Machine
IST Series
-
Jinan Testing Equipment IE Corporation
*Load meets or exceeds the following standards: ASTM E4, ISO7500-1, EN 10002-2, BS1610, DIN 51221. *Strain measurement meets or exceeds the following standards: ASTM E83, ISO 9513, BS 3846, EN 10002-4. *Safety: This machine shall conform to all relevant European CE Health and Safety Directives EN 50081-1, 580081-1, 73/23/EEC, EN 61010-1.
-
Product
Thermal Cycling Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
Product
Dairy Antibiotics Testing
-
Our range of dairy antibiotic testing equipment can be used on farm as well as in processor environments to make sure that rigorous food standards are maintained and backed with accurate results.
-
-
Product
RF/Wireless Test Fixtures
-
Test‐Head Engineering develops and manufactures RF Test Fixtures which allow the testing of RF and Wireless modules and components.
