Battery
energy store.
See Also: Lead Acid Battery, AAA Battery, AA Battery, 1.5V Battery, 9V Battery, Button Battery, C Battery, Coin Battery, D Battery, NIckel Cadmium Battery, Lithium ion Battery, SLA Battery, VRLA Battery, NICAD, Battery Test
-
Product
Electrical Power Transducers
-
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
Product
Full-Featured Life Cycle Test System
LCV
-
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Pro Model Automotive Meter W/PC Interface
595
-
The #595 is a premier automotive diagnostic tool. It is equipped with the latest testing capabilities, including Milliseconds Pulse Width, for measuring the on-time of fuel injectors. The #595 features a huge LCD display w/bargraph for easy viewing. This meter can even be interfaced to your PC or notebook computer for enhanced diagnostics and data presentation. The software and computer interface cable are included free! The #595 includes two sets of test leads, RPM pick-up, temperature probe, software CD, interface cable, protective holster, 9 volt battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
Product
Perforated Positive Coin Cell Case For In-Situ Testing
PCC1
-
Perforated CR2032 stainless steel coin cell case (4-piece set) with customizable hole diameters for in-situ electrochemical testing, gas diffusion studies, and battery material research.
-
Product
Handheld LCR Meter (100Hz to 100kHz)
ST2822
-
ST2822 series handheld LCR meter is a portable handheld measuring instrument used to measure the parameters of inductance, capacitance, resistance and other components. Small in size, powered by 8.4V rechargeable battery (ST2822A is 9V non-rechargeable battery) or external power adapter, it can be used not only in desktop applications, but also in mobile measurement and handheld measurement.ST2822 series apply the ultra-low power consumption design and high density SMD assembly techniques and can simultaneously display primary and secondary parameters on a LCD display with backlight. The dual-color shell is gorgeously once shaped; and functions are easy to operate. The test frequency is up to 100 kHz, the readings of primary parameter 40,000 counts and the resolution of dissipation factor 0.0001. Accurate and convenient measurements of passive-components can be achieved in different occasions for a long time.
-
Product
Autonomous Data Collector
DCX-25 PVDF
-
KELLER AG für Druckmesstechnik
The DCX-25 PVDF is an autonomous, battery powered instrument designed to record water depth (pressure) and temperature over long periods. The housing is made of polyvinylidene fluoride and the sensing diaphragm is available in either Hastelloy C-276 or titanium 6AL-4V. This combination of wetted materials ensures compatibility with even the most aggressive media.
-
Product
Digital Manometer
LEO Record (Ei)
-
KELLER AG für Druckmesstechnik
LEO Record is an autonomous battery powered instrument with digital display designed to record pressure and temperature over long periods. Both the piezoresistive LEO Record as well as the capacitive LEO Record (ideal for low pressure ranges) offer the following advantages:
-
Product
Coating Thickness Gauge
-
Dalian Taijia Technology Co.,Ltd
In built probe(s)● Operating principle: magnetic induction/eddy current (F/NF)● Measuring range:0-1250um/0-50mil● Resolution; 0.1/1● Accuracy: ±1-3%n or ±2.5um● Min. measuring area: 6mm● Min. sample thickness: 0.3mm● Battery indicator: low battery indicator● Metric/ imperial: convertible● Power supply: 4x1.5V AAA(UM-4)battery● Auto power off● Operating conditions:0-+45℃(32℉-104℉),≤90%RH● Dimensions: 126x65x27mm● Weight: 81g(not including battery)● Optional accessories:● other range 0-200um to 15000um● RS-232C cable & software: 1.USB adaptor for RS-232C 2.Bluetooth interface
-
Product
Power Management ICs
PMICs
-
Renesas' power management ICs (PMICs) are integrated circuits that perform various functions related to power requirements of a host system. A PMIC may have a combination of the following functions: DC to DC conversion, battery charging, linear regulation, power sequencing and other miscellaneous system power functions.
-
Product
Combustible Gas Leak Detector
Model - KM 5540EX
-
Kusam Electrical Industries Limited
• CNEX Ex ib IIB T4 GB approved.• High Quality Japanese sensor.• Anti-explosion 3.7V 1500mAH Li-ion battery equipped.• Instant sensor failure indication.• Easily check the status of alarm devices (buzzer, LEDs).• Built-in temperature compensation to provide excellent environment independency.• Audible ticker signal & visual leak size indicator.• Adjustable sensitivity, fast warm-up, low battery indicator.
-
Product
Explosion Proof Temperature Test Chamber for Power Battery
-
Komeg Technologies Explosion Proof Temperature Test Chamber for Power Battery
-
Product
Femto / Picoammeter and Electrometer / High Resistance Meter
B2980A Series
-
Both the picoammeters and electrometers provide a world-best performance of 0.01 fA (0.01 x 10-15 A) current measurement resolution. In addition, the electrometers can measure resistance up to 10 P (10 x 1015 ), which is also a best-in-class specification. Finally, since AC power line noise can be difficult to eliminate when making low-level measurements, both the picoammeters and electrometers are available in battery powered versions.
-
Product
Saluki SFS-2000 Fusion Splicer (4 motors)
-
SFS-2000 series is the new standard 4 motors fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, makes it very popular and hot.* 7s fast splicing, 14s highly efficient heating* 320/88 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 220 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
Product
Battery Analyzer
SI-9300R
-
Conventional cycler systems use PCs to transfer data from cycler channels to disk. SI-9300R instead uses advanced technology to write data direct to disk without PC intervention. For high channel count systems this dramatically reduces PC workload, increases system reliability and allows the PCs to concentrate on test control, channel monitoring and data analysis.
-
Product
Digital Multimeter
KU-2600
-
4000 count LCD 2 times / secAuto / Manual Ranging1.5V R6P or AA Batteries (x2)CATⅡ600V, CATⅢ 300V compliant155(H) x 75(W) x 29(D) mm,Approx. 180gHolster, 100-50 Test Leads, 1.5V R6P Batteries (x2 & spare),Spare Fuses F14 (0.5A/250V) (x1), Spare Fuses F17 (10A/250V) (x1),
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
Microwave Leakage Detector
-
*Microwave leakage detection:≥ 1mw/cm2*Meter points to show "SAFETY" or "DANGER" zone*No battery required*Dimension (LxWxD) mm : 53x36x23*Packaging: Sliding blister card
-
Product
Digital Milliohm Meter and Resistance Tester
4338 mO
-
Standard Electric Works Co., Ltd
● Protection class: IP65 (Lid closed)● 4-Wire method for mΩ.● It's about 100mA at 1100.0mΩ range.● It's about 10mA at 11000mΩ range.● Measures down to 100µΩ (0.1mΩ).● Maximum resolution of 100µΩ.● Large LCD (68×34mm).● Relative mode. ● Data hold function.● MAX/MIN function.● Power source: 1.5V "C" battery × 8● Long battery life and stable power. ● Low battery indication.
-
Product
Field Ttesters
-
Our product range comprises from small handheld, battery fed testers to full featured service performance assurance tools and distributed monitoring systems. We have several product lines including:QoS / SLA verification system Ethernet, IP, Critical Data, VoIP, IPTV .Hand-held testers: Gigabit Ethernet, Synchronous Ethernet, E1, PDH, SDH, Ethernet, IP, Jitter, Wander, Datacom, Frame Relay, etc.
-
Product
Digital Infrared Thermo Leak Detector
IR-711
-
Shenzhen Calibeur Industries Co., Ltd..
'-4 colors backlight to indicate thermo leak by diviation setting;'- Measurement Range: -40° to 716°F (-40° to 380°C); '- Accuracy : < 0°C： ±3% or ± 3°C ≥0°C： ±2% or ±2°C '- Distance Spot Ratio: 12:1; '- Emissive: fixed at 0.95;'- Response time: 0.5 seconds;'- ℃/℉ selectable;'- Three ranges of leak difference exchange: ±0.5℃, ±3.0℃, ±5.5℃ ±1℉, ±5℉, ±10℉'- Size: : 42*85*185mm'- Weight: 170g'- Power: 1pc 9V Battery .(not included)
-
Product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
-
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
-
Product
Digital Infrared Thermometer
IR-102
-
Shenzhen Calibeur Industries Co., Ltd..
'- Range:-20℃ ～ 330℃;'- Accuracy: < 0°C ±3°C or ±3% of showed value, ≥ 0°C ±2°C or ±2% of showed value '- Distance Spot Ratio: 8:1; '- ℃ / ℉ exchange;'- Laser Targeting Function'- Backlight,LCD Display;'- Weight: 137g'- Power: 1 * 6F22 9V Alkaline battery (not included)
-
Product
Handheld Portable XRF Spectrometer
QualiX-2000
-
Handheld Portable XRF Spectrometer - QualiX-2000 Series are widely applied in accurate and non-destructive detection on a variety of precious metal alloys, low alloy steel, stainless steel, tool steel, electronic components, batteries, toys, stationery, children's products, minerals, raw ore, etc. You can identify material composition and alloy grade.
-
Product
Optical Test And Measurement
-
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
-
Product
Ultrasonic Flaw Detector
MFD800C
-
MFD800C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed main product. Unique design, sophisticated manufacturing, convenient operation, powerful function, It takes many advantages in one unit. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it can select the operating interface style and the LCD brightness according to environment. With humanizing interface design, the waveform show delicately. It can find the defects clearly in full screen. Single hand capable for holding operation, the curve making, probe calibration and other conventional operation can be completed automatically. Core processor CPU with 400M main frequency, it can complete the complex run quickly and realize intelligent defect analysis. Low power design with large capacity and high performance lithium ion battery module，it can work more than 8 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating way in one body, customer with different habits can operate it freely. It supports many languages. Its waterproof, oil proof, dustproof function can achieve IP65 protection level. It is the necessary professional precision instrument for defect detection, quality control, on-line safety monitoring and life evaluation in fields of oil, chemical, metallurgy, shipbuilding, aviation, railways and so on.
-
Product
C/I Clamp Meters
CLAMPMETER,400A AC (CM-330)
-
*AC current measuring capability up to 400 amps*Compact size, fits easily into tool pouch*Data hold and Max hold to capture important readings*2000-Count LCD*Lifetime Limited Warranty*Accessories included: (1) 9V battery, carrying case*Lifetime Limited Warranty
-
Product
Small Objective Drop Tester
KD-208
-
King Design Industrial Co., Ltd.
Testing of Mobile phones, batteries, PDA, digital camera and other hand-held communications and IT product.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
