Battery
energy store.
See Also: Lead Acid Battery, AAA Battery, AA Battery, 1.5V Battery, 9V Battery, Button Battery, C Battery, Coin Battery, D Battery, NIckel Cadmium Battery, Lithium ion Battery, SLA Battery, VRLA Battery, NICAD, Battery Test
-
product
M-Code Mission Timing and Synchronization
SecureSync
The latest generation of modernized security architecture, modernized anti-spoofing and anti-jamming for GPS-degraded environments, operations in mixed P(Y)-code and M-Code constellations, accelerated Direct-Y and Direct-M code acquisitions, and Over-The-Air-Rekeying (OTAR). SecureSync M-code provides better than 41 dB J/S while tracking and better than 54 dB J/S while providing cryptographic key retention without battery backup.
-
product
Current Probes
PMI® introduces the convenience of flexible current probes (Flex CTs)! These 5,000A probes come in 12″, 24″, 36″, and 48″ lengths that allow you to easily surround multiple conductor bundles. They are available in sets of two, three, or four for use with different recorders. The Flex CTs are powered from recorder voltage and DO NOT require a battery pack for operation.
-
product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
product
Premise Toner Drop Cable Continuity Tester
RPT-AAA Series
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
product
Isolation Measurement System
DM-8000H
*The input block, control block and display block are isolated with optical fiber cables. (DM-900A/AL, DM-910A/AL)*Frequency bandwidth: DC to 500MHz.*Simultaneous multi-channel measurement of many channels of different reference potentials. (2 to 24 channels) (DM-900A/AL)*Long-life battery drive. (The system can be driven by three batteries for about 12 hours) (DM-900A/AL, DM-910A/AL)*Measurement using long memory. (DM-900A/AL, DM-910A/AL)*Simultaneous measurements of the inverter's switching waveform and ON-voltage. (DM-910A/AL)
-
product
Non-Contact H.V. Detector
380 HP
Standard Electric Works Co., Ltd
● Protection class : IP65.● 7 voltage settings : 120V, 4kV, 15kV, 25kV, 35kV, 46kV, 69kV● Bright LED visual indication● Vibration function● Frequency range: 40~70Hz● Audible indication● Easy-to-prove method● Power source : 9V rechargeable battery● Can be charged with the automotive● Non-contact detection by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Special ranges are available upon request● Flashlight function● Safety standard : EN 61326-1 CISPR 11● Operating temperature and humidity : 0°C ~ 40°C / 80% R.H. Max. ● Dimensions: 262(L) × 85(W) × 56(D)mm● Weight: Approx. 330g
-
product
Winding Resistance Meter 15Amps, 2 Channels
WR14
Raytech's Digital Winding Resistance meter WR14 is the battery powered version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy measurement of very low resistance of any inductive loads.
-
product
Signal Conditioner
DMA2
Din rail mountable with user selectable outputs of +/-10V, +/-5V or 4-20 mA. 10-28VDC powered suitable for battery or automotive use. Features 1000 Hz bandwidth and push-button shunt calibration.
-
product
Tone Generator with Cable Tracer
1RA470
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
product
Line Tester
LT51
The LT51 Line Tester is a portable handheld battery powered instrument for Data, DSL, Telephone, Voice Copper Line testing. It combines the features of several pieces of test equipment such as a Level Meter / Spectrum Analyser, Distortion Analyser, Oscillator, Handheld DMM and TDR in the one small lightweight package.
-
product
Battery Module
Each Gavia Battery Module contains several independent "smart" Li-Ion battery packs and battery chargers. Each battery pack is monitored for health and operational information, and the battery packs are protected against short-circuit and overcharge. The Battery Module also contains an intelligent power management processor.
-
product
Powerful AC/DC Power Supply For Testing Circuit Breakers
POB35AD
POB35AD is a power supply unit employing the latest power electronics technology. POB35AD generates ripple free DC-voltage and it is developed for regular maintenance tests of power circuit breakers. It eliminates use of stationary batteries during testing. Output voltage is selectable from 10 to 250V AC/300VDC. The test set is a powerful and versatile unit with possibility to generate up to 30A.
-
product
Hand-Held 12 Volt Combo Digital Load Tester
6028DL
• 60 Amp load to test smaller batteries: CCA and Amp hours• 125 Amp load to fully test larger batteries: CCA and Amp hours• 125 Amp clamps offer greater flexibility when attaching the hard to reach applications • Made in USA of US and Global Components
-
product
Switching Power Supply ATS (SMPS ATS)
8200
Chroma Power Supply Auto Test System model 8200 provides complete solution for PC ATX power supply, adapter and battery charger testing. The application oriented system structure makes it the most cost effective test equipment for initial test in power supply production line. To meet the power supply test requirements, Chroma Power Supply Auto Test System model 8200 has built in 20 ready-made test items. Users can simply enter the test conditions and test the power supply features while proceeding. With the report and management functions, Chroma Power Supply Auto Test System model 8200 is able to provide versatile tools to establish test documents and perform system administration.
-
product
The Field Logger
The Field Logger is a stand-alone data logger which is capable of recording potential vs. time and LPR vs. time data. The instrument is battery powered and records data onto an attached SD memory card. The instrument is entirely contained within a waterproof (IP67), tough polycarbonate enclosure (23x19x11cm), with probe connection via a single high quality watertight Lemo or Amphenol connector.
-
-
product
DC-DC Boost Converters
The ams step-up (boost) converter portfolio offers very high efficiencies of up to 96%, and the devices draw a very low quiescent current. High switching speeds enable the use of very small external inductors. These DC-DC boost converters can boost the input from a single battery cell to an output of up to 42V.
-
product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Battery Tester
BAT-200
Check the batteries! Battery failure is often the common cause for the sensor or instrument failure. Simple to use, portable universal battery tester for the standard and rechargeable batteries.
-
product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779014-01
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
product
StellarCASE Analyzers
StellarNet proudly announces new rugged and fully integrated portable Case Spectroscopy Systems for material identification, elemental and composition analysis using Raman, NIR & LIBS technologies. The StellarCASE Systems include interior mounting of spectrometer instrumentation pre-configured for “Open & Measure” application, with no additional setup required. With a simple press of the “Analyze” button instantaneous composition analysis or material/elemental match results are displayed on your screen. The StellarCASE systems feature an internal main power control system with ON, OFF, & Charge buttons and an 8 hour battery life for portable field applications. Also, includes AC power adapters for use in the laboratory and classroom.
-
product
True RMS Digital Multimeter
MM68
The MM68 is a True RMS digital multimeter which measures AC voltage up to 750V, DC voltage up to 1000V and both AC and DC current up to 10A.
It measures frequency, capacitance, resistance, and also has duty cycle, diode test and an audible continuity test which sounds at less than 100Ω. The 4½ digit LCD screen displays the results as values and on a 22 segment analogue bar graph. The MM68 also has an auto-power off feature and on screen low battery indication.
-
product
AC/DC Clamp Meter
3902 CL
Standard Electric Works Co., Ltd
● 2000 - count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ Capacitor measurement ◎ Frequency counter.● Range change function.● Data Hold function freezes the reading.● Continuity check.● Diode measurement.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
product
OTDR EXFO
AXS-110
Shanghai Tarluz Telecom Tech Co., LTD
Event dead zone: 0.8 m; Wavelengths: 850/1300/1310/1490/1550/1625 nm; Dynamic range: up to 37 dB; Battery autonomy: 8 hours
-
product
Regulated Transmitter
TIP One
The TIP One is purposely designed for shallow induced polarisation or Resistivity sounding investigations. The TIP One injects a regulated current or regulated voltage into the ground via a simple 12V battery.
-
product
Battery Pack Testing Equipment
Xiamen WinAck Battery Technology Co., Ltd.
The battery pack testing equipment is suitable for the testing of basic functions and protection functions of high-power finished battery packs. Such as lithium battery pack of power tools, garden tools, electric bicycles, backup power supplies, medical device and other products.
-
product
WiFiScope WS6: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XM-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
product
WiFiScope WS6+SureConnect: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XMS-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
product
Cell, Module & Pack Testing
Cell, Module and pack battery formats are crucial for electrification in transportation and energy. Arbin Instruments' test equipment is designed for performance-based tests, to meet the needs of these complex formats.
-
product
Portable Units
The basic version for mobile conductivity measurement. It is a robust and intuitive portable device for routine daily measurements in laboratories and processes. Over 1,000 operating hours with a single set of batteries (4x AA).
