Manual Fixtures
Connect a UUT's test nodes to test connections by hand.
See Also: Mechanical Fixtures
-
Product
Test Fixturing Solutions
-
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
-
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Stand-Alone Test Fixture
MA 2013/D/H/Pylon
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 24,00 kg
-
Product
Custom Fixtures
-
The shock and vibration fixture model BW-SV-3X3X3 is designed to accept up to 24 each of the TO-3 packages on each of the 6 axes and mount to the vibration shaker model BW-100C and Shock Tester model BW-E5000. The fixture is made of white derlin and measures 3”x3”x3”and weighs approximately 13 ounces. The fixture includes a white derlin cube with a 2 ¼” bolt circle and 4 10-32 x 3” cap screws.
-
Product
Standard & Custom Test Fixtures
-
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
MEE-B, Electrically Driven Fixtur
100845
-
MEE-B - electrically driven fixture for high actuating forces and high piece count production in the absence of a compressed air supply function and ICT test.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
-
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
Product
Headphone Test Fixture
AEC206
-
The Larson Davis Model AEC206 Binaural Test Fixture is the tool for testing supra-aural, circumaural, supra-concha, intraconcha, and insert-type headphones. Preassembled with IEC 60318-4 (711) occluded-ear simulators and TEDS compatible preamplifiers that provide electronic calibration information, the Model AEC206 is user-friendly and easy to learn. Additionally, calibration is a simple process—a custom adapter is included for the Model CAL250 acoustic calibrator or similar device.
-
Product
Test fixtures
-
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
Product
MMI-C, Mechanical Test Fixture
100640
-
Mechanical test fixture with optimised ergonomics for function test, final test and ICT applications. The MMI is prepared for both safety switches with guard locking and electrical interlocking. Our MMI-C test fixture is versatile.
-
Product
Test Fixtures & Test Sets
-
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
Product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
Product
Test Probes / Test Fixtures
-
INGUN has an unbeatable assortment of test probes and test fixtures for individual testing tasks.Thanks to many years of experience in the testing equipment field, INGUN offers the suitable test solution for every test requirement.
-
Product
MMIHF-B, Shielded Test Fixture
100223
-
Shielded test fixture for high frequency and radio application. Protection of the environment from the DUT or shielding of interfering influences on the test. With our high-frequency fixture MMIHF-B, you can test sensitive and transmitting assemblies - even those with a transmitter and receiver combination - in detail without risking consequences for your production.
-
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Manual Screw Flat Grips
-
Screw flat grips are general-purpose grips used for static tensile testing of a wide range of materials, most commonly, rubbers, plastics, textiles, and paper, and specimens such as plates and wires. Another advantage of these grips is they can be used to test thick specimens, up to 16 mm (0.63 in).
-
Product
MEE-C, Electrically Driven Fixture
100846
-
MEE- C - electrically driven fixture for high actuating forces and high piece count production in the absence of a compressed air supply function and ICT test.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
Edge Connector Fixture
220EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
Manual Test Solution
Titan
-
Titan is an easy to use, low cost Human Body Model (HBM) or Machine Model (MM) manual test solution. It can be used for design, engineering, and characterization of your devices. Ranging from 50 V to 16,000 V the Titan will have the largest voltage range of any HBM tester.
-
Product
Fixtures FMMA11
-
The FMMA11 fixture series is designed for high-performance mechanical applications, integrating advanced technical capabilities with user-friendly features. Built with a standard chassis to ensure reliability and ease of use, the FMMA11 model takes full advantage of customizable testing systems with manually generated contact interfaces capable of handling up to 850 signals. This model is particularly suitable for mechanical exchangeable cassettes, providing precise measurements and a maximum contact force of 600 N over a linear stroke of 20 mm, making it ideal for various testing environments.
-
Product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
-
LampChek indicates the lamp and fixture continuity.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Manual Oscillators
MOS-01, -01A
-
The MOS-01 manual oscillator module is used as a quality, general-purpose sinewave oscillator and digital readout monitoring system in the MAC-01, -02, or -03 AC Power Sources/Frequency Converters. The unit has guaranteed operating range of 20 HZ to 20 KHZ which is covered in three one-decade scales. The LCD digital metering system is switch-selectable to readout either frequency, voltage or current. A toggle switch selects the input for the attached AC Power Source/Frequency Converter to originate from the manual oscillator itself or from an external laboratory or programmable oscillator source. With oscillator mode switch in Internal position, the BNC connector delivers the signal to drive additional slave units or for oscilloscope sync or monitoring. BNC input/output is completely isolated with 1500 VAC breakdown and excellent common mode rejection. The oscillator modules must be factory installed and calibrated.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Manual Test Adapters
-
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
Product
Test Stand, Fixture Design and Manufacture
-
As your partner, Trialon’s commitment to providing our customers with custom test stands, test and vibration fixtures that optimizes the sample test. Our experienced staff can design and manufacture a test stand or fixture for almost any product.
