Showing results: 901 - 915 of 2823 items found.
-
A025CFR-025DMR-5A180 -
Pickering Interfaces Ltd.
This 1.8m long female 25-Pin Micro-D to male 25-Pin D-type cable assembly is constructed from 18/0.1 (26 AWG) copper wiringwith PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products.
-
4616-1, 160-PIN VME64x -
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 160-pin DIN connectors. Pad per hole pattern both sides. Voltage and Ground bus both sides. Pad and bus surfaces solder-coated for user convenience. Row and column legends provided.
-
FOD 1204 -
Fiber Optic Devices Ltd.
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
FOD1204H -
Fiber Optic Devices Ltd.
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
AX92907 -
Axiomtek Co., Ltd.
*Two independent SATA channels*Fully compatible with SATA revision 2.0 and 3.0 hard drives (HDD) and Solid State Drives (SSD)*Supports RAID 0,1*Two SATA power connectors with +5V*51 x 30 mm
-
4617 -
VECTOR Electronics and Technology, Inc.
98 contacts (49 each side) on 0.100" centers.3-Hole Solder Pads for interconnecting multiple component leads. I/O mounting area for up to 70-pin D-sub and ribboncable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
COMM-connect
The COMM-connect range of Narrow Band Low Noise Amplifiers can be used to amplify signals in a very wide range of bands. The amplifiers comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
064-758 -
ELMA Electronic, Inc.
Set of Shelf manager mezzanine board installed on the pluggable carrier board. The pluggable carrier board provides all interfaces on the rear connectors. This type of board can be used together with the Elma adapter board or directly with your customer backplane design.
-
StellarNet Inc
The StellarNet portable Light Sources facilitate measurements in the UV, VIS, and NIR for various samples and application types using standard SMA-905 optical connectors. These low cost modular components are robust, reliable, and designed to last in portable and industrial environments.
-
ONR-8636 -
Hangzhou Huatai Optic Tech. Co., Ltd.
ONR-8636 with standard configuration is a type of high index and universal in-door forward optical receiver. It adopts Philip optical receiving module. End-grade adopts power-doubling module. Optical connectors and RF connector can be installed at the front panel or back panel.
-
HR8636 -
Hangzhou Huatai Optic Tech. Co., Ltd.
HR8636 with standard configuration is a type of high index and universal in-door forward optical receiver. It adopts Philip optical receiving module. End-grade adopts power-doubling module. Optical connectors and RF connector can be installed at the front panel or back panel.
-
CAEN S.p.A.
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
PCI-7853 -
ADLINK Technology Inc.
PCI-7853 provides a Single independent HSL network and one Network port with 2 separate connectors. For more application, the Max. HSL system connecting distance using PCI-7853 can be 2400 m at the speed of 3 Mbps with HSL repeater module.
-
11581A -
Keysight Technologies
The Keysight 11581A contains a set of four Keysight 8491A attenuators 3, 6, 10 and 20 dB with type-N connectors, furnished in a walnut accessory case. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
CA-EASYGET -
UC Instruments, Corp.
The CA-EASYGET fiber endface inspector is the masterpiece of our engineer which withexcellent performance and convenient operability, trust it is the best choice for fiber endface inspection. Taking use of 220k pixel of TFT sharp and finely LCD, which magnify about 200 times of object, it makes you easier to judge the status of fiber endface. And its compact size made it ideal tool of connector endface inspection before fiber network installation, varies of adapters meet different requirements on inspect male fiber connectors&female fiber connectors, such as FC SC ST E2000 LC MU and TOSA ROSA fiber endface.