Showing results: 811 - 825 of 2823 items found.
-
106PIBM301-0000R -
ELMA Electronic, Inc.
the PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
106PIBM601-0000R -
ELMA Electronic, Inc.
the PIB 6U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Apevia Corp.
Power supply is a standard-size Flex-ATX unit that will fit in any ITX form-factor case. Has enough power output and connectors to run low-medium systems being used for versatile compact computing applications.
-
J90RJ45R -
6TL Engineering
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV module Up to three connectors per module For Cat 5 Fast Ethernet cable IEEE 802.3 standard 100 Base-T
-
AUTO DIAGNOSTECH LTD
The Sensor Imitator Probe is mainly used for the simulation of the signals generated by different types of sensors in the vehicle. It can be used in all automobiles (12V/24V), to distinguish faults that lie in the sensor itself or are related to the connectors or wires.
-
CONM50-D25-1 -
Abaco Systems Inc
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the ISA (PC/AT) carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
OPENVPX-CABLE -
ELMA Electronic, Inc.
Compliant to VITA 46 and 65, the cabling assemblies are ideal for development. They can be used for I/O to bulkhead connectors and slot-to-slot connections. Front-plug versions allow testing across the backplane or full interconnect path.
-
CX-G13 -
Shenzhen Chuangxin Instruments Co., Ltd.
Tumbling Barrel Tester The Tumbling Barrel Test simulates repeated falls which may occur to such devices as connectors or small remote control units which are normally attached to cables during use.
-
FMC424 -
Abaco Systems Inc
Electrically compliant with the VITA 57.1 standard, the FMC424 is compatible with Abaco Systems' FPGA carrier cards offering high pin count connectors. It also allows for the option to stack an additional FMC over it.
-
781131-03 -
NI
The TB-2650 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2650 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
N1420A -
Keysight Technologies
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
Pickering Interfaces Ltd.
The Standard Voltage 50-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Pickering Interfaces Ltd.
The Standard Voltage 9-Pin D-Type connector is used on PXI switching products to provide a low density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Comtel Electronics
Comtel Electronics offers the Serial Mesh Backplanes PICMG 2.20 High Speed mesh connections on ZD connectors (P4 area). Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.20 Spec.
-
COMM-connect
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.