Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 32xSPDT
42-148A-001
Relay
The 40-148A-001 (PXI) and 42-148A-001 (PXIe) 32xSPDT relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector With Backshell, Screwlocks
C096SFR-4SP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
USB 3.0 And RJ45 Cat6 To VTAC Interface
YAVAM852
Interface
USB and RJ45 sockets to VTAC VPC contactsHigh speed interface between connectors up to 1GbpsAvoids noise and interferences on signals thanks to VTAC contacts technology
-
Product
96-Pin SCSI Micro-D Female Ribbon
40-961-096-F
SCSI Female Connector
This connector is designed to allow users to terminate with IDC connections to the 96-Pin SCSI Style Micro-D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
-
Product
Low Pass and Bandpass SMA Coaxial Filters
-
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
Product
Fixed Attenuator (Coaxial)
-
RF Lambda’s fixed coaxial attenuators are used to adjust the signal level in any RF system. They are most commonly used to reduce high power signals in order to inject into test equipment or other parts of the RF system requiring lower signal levels. They are highly reliable and come in a variety of frequencies, powers, and connectors.
-
Product
Duplexers
-
Prices include interconnect cables and mounting rails or panels. Specify N or UHF connectors, or 7-16 DIN (extra cost). All duplexers are factory turned. Specify pass and reject frequencies. 30-50 MHz duplexers have a tuning range of approximately +/- 2.5 MHz from center frequency as built.
-
Product
68-Pin SCSI Micro-D Male Connector Block
92-965-068-M
Connector Block
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
Adapters
-
A variety of connector types for applications from DC up to 34 GHz!Low insertion lossExcellent return lossFlat responseRugged construction
-
Product
LXI Microwave Multiplexer, SP6T, 4-Bank, 50GHz, 50Ω, SMA-2.4
60-800-604
Microwave Multiplexer
Our 60-800-604 is a 4 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-310-001
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 12-Bank 40GHz SMA-2.9
60-802-412
Multiplexer Module
The 60-802-412 is a 4-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
160 Pin DIN 41612 Connector Blocks and Breakouts for Pickering Products
-
The connector blocks and breakouts below are suitable to use with Pickering cards and modules that utilize a 160-pin DIN 41612 connector.
-
Product
Bias T's
-
Centric RF offers Coaxial Bias T's so that a DC voltage can be applied to the rf signal path. These Bias Tee's (aka bias t) currently are offered with sma and 2.92mm connectors. Bias T's are implemented by attaching a broadband inductor to the circuit trace, with the power rating of the bias tee being determined by the size of the inductor.
-
Product
20 Pin GMCT Connectors For Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 20-pin GMCT connector.
-
Product
25 Pin Breakout Interface
VSI-Breakout-25
-
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
90 Degree Hybrid Couplers To 500 MHz
-
Hybrid couplers with bandwidths as broad as 125:1 are available for applications within 100 kHz to 500 MHz. Power handling is 1 watt maximum for a load VSWR of 1.2:1 or better. These hybrids have an isolation of 20 dB and phase balance of 3 degrees. Most models have a VSWR of 1.4:1 or better throughout their operating bandwidths.Pulsar Microwave currently offers these hybrid couplers packaged in three outlines, including an SMT version. Standard offering of connectorized packages 412 and 442 are with SMA female connectors. Outline 412 may be customized with any combination of BNC, TNC, F or N connectors. Outline E is the surface mount version and requires less than one square inch of board area, making it well-suited for portable applications.
-
Product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779373-01
Voltage Input Module
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
Product
FTTx Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.
-
Product
LXI Microwave Multiplexer, SP6T, 12-Bank, 67GHz, 50Ω, SMA-1.85
60-800-812
Microwave Multiplexer
Our 60-800-812 is a 12 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
Programmable Resistor Module
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
Passive XMC-to-PCI Express Adapter
6065
-
The Technobox, Inc. P/N 6065 is designed to adapt a single-wide XMC card to a 8X PCI Express slot. The 6065 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
Diagnostics & Testing Equipment
-
Parker offers an array of diagnostic and test solutions for measuring hydraulic and pneumatic data and for troubleshooting operational problems. These include analog and digital flow and pressure meters and viscometers as well as associated devices such as sensors, vacuum and pressure controllers, quick couplings, and test point connectors.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω SMB With Loop-thru
40-729A-001-L
Matrix Switch Module
The 40-729A-001-L (PXI) and 42-729A-001-L (PXIe) are 8x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
50-Pin SGMC Connector & Cable Accessories
-
Our 50-Pin SGMC connector is used on PXI power switching products to provide a high current user connector solution with high density.
-
Product
3U CompactPCI Serial 2-slot SSR w/ RTM w/ Ethernet
1CPCIS-302-R210
-
3U CompactPCI Serial Backplane with 2 CompactPCI S.0 slots, system slot right, with rear IO : 1x CompactPCI S.0 CPU slot, 1x CompactPCI S.0 peripheral slots, with connectors for RTMs in slot 1, full-mesh Ethernet routing.
-
Product
Power Supplies
CTI Series
-
With dual 80mm smart fan cooling your system, the CTI-series keeps running smoothly. It comes with an automatic setting to adjust the fan speed according to the level of heat. The hotter your system, the faster the fan spins, and the faster your system cool. With great ventilation, you no longer have to worry about your system overheating. It is dual PCI-E connector ready (700W only) for your graphic rendered fun.
-
Product
1000BASE-T1 MEDIACONVERTER
Art.-Nr.: TE-1401-1
-
The ideal physical layer conversion between Automotive Gigabit Ethernet and your PC system The 1000BASE-T1 MediaConverter establishes one direct point-to-point conversion between automotive ECU’s using 1000BASE-T1 and any standard Gigabit Ethernet device with RJ-45 connector.
