Product

Socket Tester

ST120+

-

Fluke Corporation

ST120+ - Fluke Corporation

The Fluke ST120+ GFCI Socket Tester with Beeper checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120+ will give you confidence on your next job.

Product

Circbord

8019

-

VECTOR Electronics and Technology, Inc.

8019 - VECTOR Electronics and Technology, Inc.

2-sided board, circuit pattern on both sides, holes plated thruIdeal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. Solder coated pattern on both sides of board. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.

Product

AUTOMATED TEST STAND DESIGN

-

DMC, Inc.

DMC, Inc.

Automated test systems may be as simple as a laptop with a DAQ module or a stand-alone controller, but they typically require a mix of off-the-shelf and custom hardware. All that hardware is integrated and wired into a test stand. Portable or mobile test stands are ideal for in-the-field research and development and servicing of multiple laboratories or manufacturing lines. Test stand access to the front panels of hardware and subcomponents allows manual configuration of non-automated settings. Quick disconnects, cable harnesses, and easy access to probes provides efficient setup and tear-down. Expandable or modular rack mount and card base systems facilitate future needs. Ergonomic considerations include keyboard and display placement, along with number of monintors. Safety is always crucial with proper E-stop placement and keeping dangerous elements away from users.

Product

3 ft Coax Wire with a Coax Pin

GX96411

-

Marvin Test Solutions, Inc.

GX96411 - Marvin Test Solutions, Inc.

One 3 ft Coax Wire with a Coax Pin Crimped on One EndRequires the GX96409 connector housing.

Product

Solid State Active Synchro Control Differential Transmitter

-

Computer Conversions Corporation

Computer Conversions Corporation

The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.

Product

SafeBloc

-

Interpower Corp.

Interpower Corp.

A SafeBloc is an accessory device, which can be used with other test equipment, as an adapter, to connect and test power cords and wiring harnesses for production testing purposes, prior to installation into equipment. Such testing would include Hipot and continuity testing of the power cord or wiring harness. The SafeBloc allows the bare wires of a power cord or wiring harness to be connected to the test equipment via clips inside the enclosure. Power can only flow through the device once it is closed and the test sequence is then started, ensuring that the test operator will not get shocked during the testing procedure. Power cord manufacturers and CEMs manufacturing custom wiring harnesses would be typical users of such a device.

Product

Self-Contained Metering Site Training Bench

Model 8813

-

Powermetrix Systems

Model 8813 - Powermetrix Systems

The PowerMaster® 8813 is a true 3-phase training simulator for metering technicians to help improve their troubleshooting skills for applications encountered in the field. The Model 8813 provides a safe, controlled environment to help the trainee accelerate their education in meter testing and wiring verification. The training simulator also features the ability to simulate over 28 commonly found metering errors in the field. Paired with the Training Administrator Station (TAS), the bench can be controlled remotely over a closed WIFI network, and each trainee’s performance is recorded and time stamped for every session.

Product

Wired Hazard Monitoring

-

Electro-Sensors, Inc.

Electro-Sensors, Inc.

Grain dust is extremely volatile and can easily explode with the proper ignition source in confined spaces. OSHA has mandated that grain elevators in Class II, Division 1 environments must have the 3 monitoring sub-systems for elevator safety (1910.272(q)(4)(ii), 1910.272(q)(5), 1910.272(q)(5)).

Product

Saluki S2107 Series Optical Cable Identifier (up to 36dB)

-

Saluki Technology Inc.

Saluki Technology Inc.

S2107 Series Optical Cable Identifier is an intelligent instrument designed for the construction and maintenance of optical cable lines in optical communication system. In view of the complex wiring environment and the difficulty of locating faults during the construction and long-term use of optical cables, S2107 series can provide fast, effective and accurate fault solutions. When the target optical cable is bent or shaken, the optical cable census instrument can quickly capture the vibration signal and display it through waveform and sound, so as to locate the target optical cable quickly.

Product

Cryogenic Applications

-

Celadon

Celadon

Over the last 20 years the Celadon Engineering team has developed an expertise in cryogenic materials which has resulted in a solid reputation in the industry for producing extremely stable cryogenic on-wafer probe card as well as DUT probing solutions. These custom cryogenic probe card solutions are widely used to test Space, Military, Medical and Quantum Computing products. Celadon’s cryogenic solutions vary from standard VersaTile™ footprints which interface to positioners to innovative custom PCB based designs to allow for flexibility when testing at these very cold temperatures. Lakeshore cryogenic wire is used in standard DC solutions for high density cableout designs to support high pin count applications. During the development process, Celadon works closely with the cryogenic prober vendor to ensure the integrated solution is optimized for current and future testing needs.

Product

Digitizers

2745 Family

-

CAEN S.p.A.

2745 Family - CAEN S.p.A.

The 2745 Digitizer is a 64-channel digital signal processor for radiation detectors available in VME64 (V2745), VME64X (VX2745), and Desktop (DT2745) form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others. The 2745 can perform pulse height measurements (PHA), constant fraction timing (CFD), charge integration (QDC) and pulse shape discrimination (PSD) independently for each of the 64 channels.

Product

Control Wires Surge Suppressors

AS-8SP / AS-12SP / AS-16SP

-

Array Solutions

AS-8SP / AS-12SP / AS-16SP - Array Solutions

Array Solutions Control Wires Surge Suppressors

Product

Air Pressure Transducers

-

Van Leeuwen Test Systems BV

Van Leeuwen Test Systems BV

Air pressure transducers can measure the cylinder and system pressures of pnuematic braking systems. With these pressures extrapolation calculations can be performed in order to determin the efficiency of laden vehicles when measured empty or partially laden.VLT offers wired and wireless models.

Product

Bending Test Machines

-

Infinity Machine International Inc.

Infinity Machine International Inc.

Bending Test Machines by Infinity Machine International Inc. - for applications such as bending cycle test machine wire wing left and right tester, 90° 180° bending wire swing test left and right optical cable repeated bend testing machine, cable bending durability tester, cable flex bending test machine, high precision bending test machines, and more.