Wire
See Also: Contacts, Harness, Connectors
-
Product
Impulse Spark Tester
IT-25B
-
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
-
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Non-Linear Junction Detector
ORION® 2.4 HX
-
The ORION 2.4 HX Non-Linear Junction Detector (NLJD) detects electronic semi-conductor components in walls, floors, ceilings, fixtures, furniture, containers, or other surfaces. The ORION 2.4 HX NLJD is made to detect and locate hidden cameras, microphones, and other electronic devices regardless of whether the surveillance device is radiating, hard wired, or turned off.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Cut Ends, 1m
A015DF4-C-0A100
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m
A015DM5-C-0A050
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Tinned Ends, 1m
A015DF4-T-0A100
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Ferrules, Screwlocks, 0.5m
A096SFR-F-6A050
-
The 96-Pin 1.27mm Pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
Ultrasonic Generators
-
F&K Physiktechnik develops and manufactures fully digital ultrasonic generators. Ultrasonic power levels are available for fine wire bonding as well as for heavy wire and die bonding applications. All generators could be used with our ultrasonic transducers, but also with third party transducers.
-
Product
Electronic Dmm Test Lead Kit For Hand-Held Meters
5543B
-
Electronic DMM test lead kit for hand-held meters. Test leads with a right angle banana plug are ideal for use with hand held digital multimeter. Flexible test leads feature high strand count silicone wire for extreme flexibility and high temperature resistance.
-
Product
Cable Assembly, 9-Pin D-Type, Male To Unterminated With Ferrules, 2m, HV
40-972-009-2m-MU-HV
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a.Clear line. b.Busy line. c.Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
Ultra-Compact Testers
-
adaptronic wiring testers of the ultra-compact class are available as low voltage testers and also as high voltage testers, as KT version with display and keyboard and as NT version with the grafical user interface NT Control.
-
Product
Wire Damaged Tester
WDT-1
-
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
-
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
6-24V Circuit Tester
1789
-
Peaceful Thriving Enterprise Co Ltd
*Check on 6 and 24V.*For use on automotive fuse blocks, marine fuse blocks, light sockets and trailer wiring.
-
Product
Cable Assy 68-Pin SCSI Micro-D F/F 0.5m
40-970A-068-0.5m-FF
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
MS-M Style 26-Pin RF Cable, Female To SMB, 1m, RG316 Cable
40-979-526-3-1m-SMB
-
This 1m long MS-M style RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz. Screwlocks are provided to secure the MS-M style connector to the associated product.
-
Product
Stellar 4000 Bondtester
-
STELLAR 4000 is the platform of choice for all manually operated pull and shear production bond testing. Configure as a simple bond wire pull tester, or upgrade for ball shear, die shear, bump pull, and tweezer pull testing.
-
Product
Superconductors and Metal Composite Materials
-
Bruker is a leading manufacturer and developer of advanced materials for applications in energy, health care, industry and research. Our advanced materials product portfolio covers wire products and components based on
-
Product
Rotatable Directional HF Antennas
-
Kratos Defense & Security Solutions, Inc.
Kratos’ horizontally polarized rotatable log-periodic antennas are constructed with wire radiators supported by a strong and unusually lightweight support structure.
-
Product
80-Channel Reconfigurable Digital PMC
2979
-
The 80-channel Reconfigurable Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring high speed single-ended operation. 64 of the 80 signals are available out the PN4 connector, while all 80 signals are wired to the front panel connector.
-
Product
230V AC Socket Tester With RCD Test (For UK)
1944
-
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*RCD Test.*30mA leakage current measurement.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon idnicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1.5W*Frequency: 50Hz
-
Product
Thermometer, -20°C to +400°C, 7.9 ", 2.7 ", 1.2 "
72-6700
-
Infrared Thermometer*Three thermometers in one...Infrared, Pt100 ohm and Thermocouple*Accommodates 4 wire Pt-100 ohm probes and thermocouple types K, J, R, T, and E.*Selectable readings °C or °F*Data Hold function*Min./Max memory function*Laser guide for IR function*RS 232 output*Auto power off
-
Product
MS-M 26-Pin RF Cable Assembly, Female to Unterminated, 0.5m, RG316 Cable
40-979A-526-3-0.5m-FU
-
This 0.5m long MS-M RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the mating connector.
-
Product
Cable Assy 9-Pin D-Type, F/F, 2m
40-970-009-2m-FF
-
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 1m, 45º
A1604F5-T-0A100
-
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
PCI-6516, 32-Channel, ±30 V, Source Outputs, Bank-Isolated Digital I/O Device
779082-01
-
The PCI-6516 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6516 module is an industrial digital I/O interface, with all channels on an isolated bank. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6516 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 1.8m, Economy
A025CFR-C-ZA180
-
This economy 1.8m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 7/36 (28 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 0.5m, 90º
A1604FT-1604FT-0A050
-
For applications where a 90 degree down cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 0.5m
40-972-068-0.5m-MU
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
