Wire
See Also: Contacts, Harness, Connectors
-
product
Cable Assy 9-Pin D-Type, F/F, 1m, HV
40-970-009-1m-FF-HV
A 9-Pin D-Type Cable Assemby for general use constructed from PTFE Type C insulated wire. The connector assembly can be secured to the product by screwlocks.
-
product
Back Plane Tester
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
product
MANIA TEST PROBE
SERIES 76
ElectricalMAXIMUM CURRENT: 3 amps continuousat working travel, non - inductiveRESISTANCE: At 35 mA test current,50 mOHMS meanMaterial and FinishesPLUNGER: Heat treated berylliumcopper, FINISH: -2E / -2P Hard nickel plated-2D / -2E138 24 Kt gold plated,BARREL: Phosphor bronze, nickel platedSPRING: Stainless steel, silver platedPIN: Music wire, hard nickel plated
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 1m, Screwlocks
A068SMR-C-6A100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Video Distribution Systems
VDU-100 Series
Systems Engineering & Management Company
SEMCO'S tactical military products have been developed in response to the requirement for near real-time, high-quality, encrypted video and sensor data capture, transmission and distribution in support of covert and overt military operations. These products provide for unprecedented audio-video and data communications from warrior-to-warrior as well as from warrior-to-command. Transmission modes include tactical and handheld radios, wireless and wired LAN, SATCOM, wireless Mesh, and Cellular, with full motion video capability in as low as 125 Kbps bandwidth. Video resolution, bandwidth and frame rates are adjustable, with high quality video frames capable of being transmitted in bandwidths as low as 9 Kbps. These products include video recording, with both local and remote download capability, as well as remote video enhancement, pan, tilt and zoom control, and multiple NTSC/PAL camera and imaging device interfaces. With administrative and password control, these products provide for unlimited remote viewing on PCs, Androids, iPhones and iPads anywhere in the world.
-
product
Insulation Type K Thermocouple
CX-K01
Shenzhen Chuangxin Instruments Co., Ltd.
K Type Thermocouple for Glow Wire Tester Insulation type high temperature resistant armored thermocouples
-
-
product
Electrodes Sensor
6013
When selecting electrode sensors an important factor is to consider the specific characteristics of the liquid involved, the lengths required to obtain the desired control of levels, and the physical nature of the container.B/W Controls' line of electrodes has been developed to provide a practical, economical solution to almost every conceivable application and installation problem.Our electrode sensors are available in several varieties: solid rod (rigid), wire suspension, and standard gland plugs for high vibration applications. In addition, we offer custom options made per customer’s requirements.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
100 Pin Micro-D Cable, Male to Male, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9A200
This 2m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
product
3-Pin Power D-Type Cable, Female to Unterminated, Ferrules, 1m
A003PF4-F-5A100
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Test Equipment
ST9020
Shenzhen Star Instrument Co., Ltd.
The ST9020 single-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.1 and 0.05. As divided by structure there are combined type, integrated type and auto wiring type. The meter test equipment is controlled via PC-based software. Choices of meter position are 6, 12, 24, 30, 48 and 60.
-
product
PreEqualization Analyzer
Quickly locate upstream impairments. See micro-reflections and group delay. Find issues like microfractures, reverse splitters, corroded connectors and bad wiring. Display modems being impacted by a common impairment. Save time and money. Reduce truck rolls. Lower maintenance costs. Increase operational efficiency.Improve customer satisfaction Benefit from pre-equalization without masking problems Find and fix problems before they impact customers
-
product
PXIe-4113, 2-Channel, 10 V, 6 A PXI Programmable Power Supply
782857-02
The PXIe‑4113 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
product
CO2 Concentration and Temperature Transmitter
T8148
CO2 concentration and temperature transmitter with two 4-20mA outputs is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 239Ω
40-253-113
The 40-253-113 is a programmable resistor module with 1 channel which can be set between 1Ω and 239Ω with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
20-Pin GMCT Cable, Male To Unterminated, Tinned Ends, 16A, 2m
A020GMR-T-1B200
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product.
-
product
Function Test Systems
These specialist Automeg models test the function and integrity of wiring harnesses combined with active components such as relays, switches, contactors, diodes, LEDS, actuators and other active components.Our software takes the complex and traditionally long task of creating functional tests away from the test engineer and allows these to be created automatically, from existing ECAD data and our component library and automated software routines. All the different routes and subtests are automatically calculated in seconds.
-
product
Cable Assembly, 50-Pin D-Type, Male to Male, 1m, Exit Towards Pin 1
A050DM5-050DM5-0A100
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Midi Logger
GL240
Its compact size contains an isolated input system which ensures that signals are not corrupted by inputs to other channels, thus eliminating wiring concerns. The GL240s multi-type inputs are suitable for voltage, temperature, humidity, pulse, and logic signals, enabling combined measurements of different phenomena like temperature/humidity and voltage. power ground allowing off-ground measurements using shunts, as well as powered or grounded thermocouples.
-
product
SPL-03C-114 Step Probe
SPL-03C-114
Current Rating (Amps): 6Average DC Resistance lower than (mOhm): 50Test Center (mil): 125Full Travel (mil): 170Full Travel (mm): 4.32Recommended Travel (mil): 127Recommended Travel (mm): 3.23Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
product
3-Pin Power D-Type Cable, Male to Unterminated, Ferrules, 1m
A003PM5-F-5A100
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Textile Tester
USTER TESTER 6-C800
The USTER TESTER 6-C800 is ready for the most demanding technical textiles applications. The amazing diversity of technical textiles applications is matched by the wide variety of quality characteristics needed in the raw material used so filament yarn producers know they must work to the most stringent specifications and standards. Quality failings, especially in the critical parameter of yarn evenness, can be expensive, but the USTER TESTER 6-C800 provides fast, accurate testing to the tightest tolerances, protecting filament producers against customer complaints and claims. Raw materials for technical textiles cover a wide range of end-uses and performance requirements. Viscose fibers, for instance, are found in lightweight blouses as well as in wire cording and high-speed car tires. Polyester, common in low-price clothing, is also transformed in special high-tech versions, for sophisticated sportswear and outdoor clothing. Countless other examples of technical applications for filament yarns span sectors such as medical, industrial, transport, engineering and protective clothing. Despite this variety of products, there is one fundamental requirement which is common to all: the absolute need for yarn evenness, measured to close tolerances, to ensure that the functional and aesthetic properties of the finished article achieve the high quality standards that customers demand.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Female, 1m
A025CFR-025CFR-5A100
This 1m long female to female 25-Pin Micro-D Cable Assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
Power Distributor
AV-P3040
"AV-P3040" can supply 40A (20A x 2). The power supply can be wired directly from the distribution board and equipped with two 20A breakers.
-
product
Lever Handle Bed of Nails Testers
Automator Manual Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
AC/DC Voltage Detector (CONTACT TYPE)
LVD-20
Standard Electric Works Co., Ltd
Contact type. LED indication and audible alarm sound when voltage is present. Designed for AC/DC voltage detection. Used for bare wires or conductors. Self-test function. For indoor use only. Low power consumption. Light weight and compact.
-
product
Cable Tester
LX-560A
Shenzhen Lian Xin Technology Co., Ltd.
Cable/Harness Tester (low-pressure type) features its capability of testing the components inside the wire, the test speed more than double faster than that of the traditional wire testers, and the provision of such functions as unilateral, turn-on resistance editing, and spot metering color editing.
-
product
Multitester Probe Set
Probes for multitesters - could wire for grounding, red connecting wire. Multitesters not included.
