Proton Exchange Membrane Fuel Cell
-
Product
Load Cells
-
Honeywell Industrial Automation
Honeywell Sensotec manufactures a wide range of tension, compression, and universal measurement load cells. These load cells are manufactured as standard, modified standard, and custom sensors to provide fast delivery. Many units can ship from our extensive stocking program within 24 hours.
-
Product
Battery analyzer For Coin Cell 5V20mA
TOB-5V20mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Analyzer (0.1-20mA, up to 5V) Lithium Coin Cell Battery Research. TOB-5V20mA Battery analyzer is an eight-channel battery analyzer to analyze small coin cells with a range current 0-20mah, voltage 0-5v.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBO SERIES
-
The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.
-
Product
LC/MS/MS Method Package For Cell Culture Profiling Ver. 2
-
This Method Package enables the analysis of 125 compounds in under 20 minutes per sample. Performing analysis separately for each compound group such as amino acids and vitamins makes profiling of cell culture components very laborious, but with this method package a large number of culture medium components and secreted metabolites can be analyzed simultaneously.Compared to the previous version, several metabolites derived from amino acids, nucleic acids and the TCA cycle have been added, allowing even more comprehensive profiling information to be gathered.
-
Product
Single Point Aluminium Load Cell
EST-4
-
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
-
-
Product
Automated Pick And Collection Tool Of Cell Colonies
CELL PICKER
-
Pickup and Remove Cell Colonies with Complete Freedom
-
Product
Single Cell Hardware
-
A Fuel Cell Hardware Assembly consists of a pair of Poco Graphite Blocks with a precision, machined flow-pattern (pattern is serpentine unless otherwise specified by the customer), and a pair of gold plated connectors fastened with aluminum end plates. Gas inputs and outputs are through Swagelok fittings. A thermocouple well and two cartridge heaters are also provided. A single Anode Reference Electrode may be added for an additional cost. The FCT Cell Hardware does not include a Membrane Electrode Assembly (MEA).
-
Product
Cell Production Measuring Technology
-
More than 2000 halm systems are already installed in the field, all of which fully comply with the IEC60904-9 standard. In the latest standard (Edition 3.0), our current systems are even rated A+A+A+.
-
Product
Cell Testing
-
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
Product
Fuel Flow Info
-
Custom range and dial markings are available. Call UMA representative for details!
-
Product
Rod End Load Cells
-
Our rod-end load cells are designed for integration into tension measurement. They are versatile, durable, and fit easily into small spaces such as inline with vehicle tie rods.
-
Product
Thru Hole Donut Load Cell
-
Futek Advanced Sensor Technology, Inc.
The Thru Hole Donut Load Cell Series offers 5 models built for Off-Center Loading, Press, or Inline compression applications. These models have a very robust construction available in 17-4 Stainless Steel, with an I.D. range of 1/8" to 1 1/4".
-
Product
Pancake Load Cell
-
Futek Advanced Sensor Technology, Inc.
The Pancake Load Cell category offers 20 models built for Endurance, Off-Center Loading, or Inline applications. These models are available in a wide capacity
-
Product
High Speed Load Cell Test Interface
LCIC-4CH
-
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
-
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
Solar Cell Characterisation
-
The PVE300 permits the determination of device spectral responsivity (from which may be determined EQE), and, having performed measurements of sample reflectance (and transmittance where required) the determination of IQE.
-
Product
Medical Mask Gas Exchange Pressure Difference Tester
DRK371-II
-
Shandong Drick Instruments Co., Ltd.
It is used to measure the gas exchange pressure difference of medical surgical masks and other products.
-
Product
Fuel Cell Hardware
-
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
Product
SFC-FID System For Fuel Analysis (For ASTM D5186 And D6550)
SFC-4000 Series
-
The SFC-FID has been developed for a range of applications including measurement of hydrocarbons in fuels.
-
Product
Voltammetry Cell
SVC-2
-
SVC-2 Voltammetry cell can be used for 4 modes voltammetry cell setup. Each voltammetry cell has its specific feature. However, SVC-2 can be sed in 4 modes. Also can apply as an oxygen-free voltammetry cell.
-
Product
Spectro UV-Vis Double PC 8 Auto Cell Scanning Spectrophotometer
UVD-3200
-
Spectro UV-Vis Double PC 8 Auto Cell is a high performance UV-Vis double beam automatic scanning spectrophotometer. Spectro UV-Vis Double has a brand new optical system design, microcomputer controlled. It is capable of processing data, from analytical and spectrum testing. Precise with high accuracy of measurement and stability are also provided by the powerful built in software and large LCD screen, which can display the screen menu and other functions.
-
Product
Diffusion Cell Testing
-
Teledyne LABS Phoenix™ Dry‐Heat Systems make diffusion‐cell testing faster, easier, and more economical. The Phoenix Systemincludes an advanced diffusion cell design. Options include the compact Phoenix DB-6 six‐cell manual sampling system and the Phoenix RDS automated sampling system capable of handling up to 24 diffusion cells at once.An important advantage of the Phoenix System is the speed with which receptor cell contents are homogenized. Visual testing with red dye placed on the surface of the media at the top of the sampling arm shows complete dispersion occurs within a few seconds.Explore the pages in this section to learn more and to configure your own system.
-
Product
Test Cell Vibration Monitoring System
-
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
Product
Test Cells
Immunity
-
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They exceed the requirements of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing. The Cells are a modified form of GTEM cell, using a balanced dual septum design which maximises EUT volume for a given external size of cell, and dramatically improves field linearity. The EUT volume is fully lined in structural polycarbonate capable of supporting heavy products and access is via a large, full height door at the end of the cell. Adjacent to the door is the I/O filter compartment which can be customised to suit the users requirements. USB, RS232, Parallel, Ethernet, co-ax and other product specific filters can be added at time of ordering.
-
Product
Portable Engineered Test Cell
PET
-
PET is an innovative portable engine test cell. Most test cells are designed by an architect and built of conventional materials like bricks and mortar, making the cells immovable and inadaptable to changing requirements. Emprise has developed a practical alternative to this PET a portable and modular engine and component test cell.
-
Product
Suitable For Strain Gauge / Load Cell Sensors
SEM1600B -
-
Suitable For Strain Gauge / Load Cell Sensors
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
