Proton Exchange Membrane Fuel Cell
-
Product
Low Profile Universal Tension or Compression Load Cell
LPU SERIES
-
Our LPU Series are low profile, universal tension or compression "pancake" type load cells. They are available in 14 ranges from 100 lb through 50,000 lb Hold down bolt holes are provided through the outer diameter and a threaded hole provided through the center for pushing or pulling from either end. The ALB load buttons located in our accessories section, are ideal for compression applications. The LPU Series are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
MFP-570 Main Fuel Pump
-
The MFP-570 provides main engine burn flow as well as servo flow and engine actuator flow. This two-stage “cartridge type” fuel pump is designed to be inserted directly into the engine fuel metering unit.
-
Product
Load Cells
-
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
Product
Test Cell Vibration Monitoring System
-
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
-
Product
Standard Shackle Load Cell
SS-3.0
-
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
PTFE Spectroelectrochemical Cell For Photocatalysis
PTS-1
-
PTFE spectroelectrochemical cell with quartz window for photocatalysis, supporting 3-electrode setups and horizontal light source. Available in 5–100ml with 24mm or 32mm window.
-
Product
Load Cell Indicator
9840
-
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
Product
Double-Layer Electrolytic Cell | Five-Neck Water-Jacket Design
DLF-1
-
DLF-1 double-layer electrolytic cell designed for temperature-controlled electrochemical experiments, electrocatalysis, and laboratory three-electrode systems. Available in single-layer and water-jacket configurations from 50ml to 500ml with five-neck structure and multiple PTFE sealing accessories.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
Power Module Test Cells
-
SPEA’s Power Module Test Cells are the complete industrial equipment oriented to the production test requirements of IGBT semiconductor power modules for consumer, transportation, energy production, industrial applications.SPEA’s Power Module Test Cells provide a turnkey solution for the automated handling, contacting and testing of these products, with the capability to force and measure the very high current (up to 1000 A) and voltage (up to 2500 V) values required for a complete, reliable test.
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
Product
Fuel Injection Pressure Tester w/2 Gages & Quick Couplers
53950
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
Product
On-Board Fuel Consumption Detector
MF-3200
-
- High accuracy within ±0.2 % of reading- Compact size and light weight- A fuel cooling function is provided as standard.- Simultaneous measurement of temperature and pressure together with the flow rate
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Fuel Injection Pressure Tester with 2 Gages
33950
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
GTEM cells
-
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
Product
H-Type Electrolytic Cell
HT-1
-
Modular dual-chamber electrochemical reactor with a replaceable ion-exchange membrane, available in sealed or non-sealed versions. Ideal for membrane-separated electrolysis, electrocatalysis, gas-involved studies, water splitting, CO₂/N₂ reduction, and mechanistic electrochemical research.
-
Product
High Precision Compression Type Load Cell
ZR
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
Stimulus Test Cell
HA7200
-
The HA7200 enables these improvements by providing high-speed, high-accuracy temperature and pressure test for automotive sensor R&D and production. Advantest’s proprietary temperature control technology delivers an optimized test solution for high-spec pressure sensors across a broad range of temperatures, in the automotive industry and beyond.
-
Product
Rod End Load Cells
-
Our rod-end load cells are designed for integration into tension measurement. They are versatile, durable, and fit easily into small spaces such as inline with vehicle tie rods.
-
Product
Acrylic Electrolytic Cell
CAE-1
-
Custom acrylic electrolytic cell for electrochemical testing, electrolysis, and electrodeposition. Transparent PMMA body with customizable ports and dimensions.
-
Product
Test Cells
-
Our test cells are built using a modular system. This means that the usable space size and shape can be specifically adapted to the required conditions.
-
Product
Single Point Aluminium Load Cell
EST-5
-
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
Product
Swagelok-Type Three-Electrode Battery Test Cell
STB1
-
A Swagelok-type three-electrode electrochemical test cell designed for battery research, electrochemical analysis, catalyst evaluation, and laboratory material testing.
-
Product
Through Hole/ Donut Load Cell (3.00 O.D.) Compression Only
THD SERIES
-
Our THD Series through hole donut load cells offer an outside diameter of 3.00 inches and up to nine different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
